ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Microstructure and Properties of Bionic TIG Welded Joints of AZ31B Magnesium Alloy

Literature Overview and Core Findings

This study by Shi Haifang and colleagues from Liaoning Technical University, published in Journal of Materials Heat Treatment in 2023, investigates the use of laser remelting to create a biomimetic "soft-hard" alternating structure on the surface of TIG welded AZ31B magnesium alloy joints. The work is inspired by the mechanical properties of biological structures, such as the shell of a mollusc or the exoskeleton of an insect, which combine hard and soft regions to achieve a combination of strength and toughness that is superior to a homogeneous material. The authors used laser remelting to create a pattern of hard, fine-grained regions on the surface of the weld, and they evaluated the microstructure and mechanical properties of the resulting joints.

The key findings are summarised below.

Parameter Conventional TIG Joint Bionic TIG Joint Practical Significance
Grain size in treated zone Coarse, dendritic Fine, equiaxed Improved strength and ductility
Microhardness in treated zone Lower Significantly increased Better wear resistance and fatigue resistance
Ultimate tensile strength Baseline Increased Stronger joint
Elongation Baseline Increased More ductile joint
Fracture behaviour Localised deformation Stress redistribution through soft-hard structure Delayed fracture, higher energy absorption

Interpretation of Technical Points

The biomimetic approach is based on the principle that a structure with alternating hard and soft regions can distribute stress more effectively than a homogeneous structure. When a load is applied, the hard regions carry more stress, while the soft regions deform and redistribute the load to adjacent hard regions. This prevents the concentration of stress at a single point and delays the initiation of fracture. In the context of a welded joint, the heat-affected zone and the fusion zone are often the weakest regions, and they are prone to premature fracture due to grain coarsening and the presence of brittle intermetallic phases.

The laser remelting process creates a fine-grained structure in the treated zone because of the rapid solidification that occurs when the laser beam passes over the surface. The cooling rate in laser remelting is much higher than in TIG welding, and this suppresses grain growth and promotes the formation of fine equiaxed grains. The fine grains increase the hardness and the strength of the treated zone, while the soft regions between the hard tracks provide the ductility and the ability to absorb energy.

The combination of strength and ductility is the key advantage of the biomimetic approach. In conventional welding, an increase in strength is often accompanied by a decrease in ductility, because the strengthening mechanisms, such as grain refinement and precipitation hardening, reduce the ability of the material to deform plastically. The biomimetic structure avoids this trade-off by creating a composite structure in which the hard regions provide strength and the soft regions provide ductility. The result is a joint that is both stronger and more ductile than a conventional joint.

Integration with Engineering Practice

The biomimetic approach is particularly relevant to magnesium alloy components in aerospace and automotive applications, where the weight savings from using magnesium must not be compromised by poor weld properties. Magnesium alloys have a low density and a high specific strength, but their weldability is poor, and the welded joints often have reduced strength and ductility. The biomimetic treatment could improve the mechanical properties of the welded joints and allow magnesium components to be used in more demanding applications.

In my experience with magnesium alloy components, the main challenge is not the welding itself but the post-weld properties. The heat-affected zone is often the weakest region, and it is prone to premature fracture under cyclic loading. The biomimetic treatment could be applied to the surface of the weld and the heat-affected zone to improve the fatigue resistance and the static strength. However, the treatment requires a laser system, which is an additional capital cost, and it adds a processing step to the production cycle.

The practical implications for production are significant. The laser remelting process can be automated, and it can be integrated into the welding cell. The laser beam can be scanned over the weld surface using a galvanometer scanner, and the pattern can be programmed to match the geometry of the weld. The process parameters, such as the laser power, the scanning speed and the track spacing, must be optimised for each alloy and each weld geometry. The treatment must be applied after welding and before any post-weld heat treatment, because the laser remelting changes the microstructure of the surface.

Key Questions and Reflections

The study raises an important question about the applicability of the biomimetic approach to different joint geometries. The authors used a butt joint, but the approach could also be applied to fillet welds, lap joints and corner joints. However, the laser remelting process requires access to the weld surface, and the beam must be positioned accurately relative to the weld. For complex joint geometries, the laser scanning pattern must be adapted, and the process may not be suitable for joints that are not accessible.

Another question is the effect of the biomimetic treatment on the corrosion resistance of the joint. Magnesium alloys are susceptible to corrosion, and the laser remelting process may change the corrosion behaviour of the surface. The rapid solidification may refine the microstructure and reduce the galvanic corrosion between the α-Mg matrix and the β-Mg17Al12 particles, but it may also introduce residual stresses that increase the corrosion rate. The corrosion behaviour of the biomimetic joints must be evaluated before the treatment can be used in applications where corrosion is a concern.

The economic case for the biomimetic treatment depends on the value of the component and the cost of the laser system. For high-value aerospace components, the additional cost of the laser treatment may be justified by the improvement in mechanical properties and the reduction in rejection rates. For low-value automotive components, the cost may not be justified, and conventional post-weld heat treatment may be more economical.

Study Insights and Implications

This paper is a valuable contribution to the field of post-weld treatment of magnesium alloys, and it demonstrates that the mechanical properties of welded joints can be improved by creating a biomimetic surface structure. The combination of strength and ductility is particularly noteworthy, because it avoids the trade-off that is common in conventional welding. The stress redistribution mechanism, which is confirmed by finite element analysis, provides a theoretical basis for the improvement in mechanical properties.

From a production standpoint, the key insight is that the biomimetic treatment can be applied to the surface of the weld and the heat-affected zone to improve the mechanical properties without changing the overall geometry of the joint. The treatment is a surface modification, so it does not affect the internal structure of the weld, and it can be applied to the surface of the joint after welding. The process is compatible with automated production, and it can be integrated into the welding cell.

The practical guidance for fellow engineers is to consider the biomimetic treatment for magnesium alloy components that require high strength and ductility in the welded joint. The treatment should be validated with a full mechanical testing programme, including tensile testing, hardness testing and fatigue testing, and the corrosion behaviour should be evaluated. The process parameters should be optimised for the specific alloy and joint geometry, and the treatment should be applied consistently to ensure uniform properties.

In summary, the biomimetic approach is a promising method for improving the mechanical properties of TIG welded AZ31B magnesium alloy joints. The laser remelting creates a fine-grained surface structure that increases the hardness and the strength, while the soft-hard alternating structure provides the ductility and the ability to absorb energy. The result is a joint that is both stronger and more ductile than a conventional joint. The approach has the potential to improve the performance of magnesium alloy components in aerospace and automotive applications, and it is a valuable addition to the toolbox of post-weld treatments. The paper is a useful reference for welding engineers and materials engineers who are working on magnesium alloy components, and it reinforces the principle that innovative solutions to material limitations can be inspired by nature.