Thermal Behaviour and Microstructure Evolution in TIG Additive Manufacturing of 316L Stainless Steel: A Shop-Floor Perspective
Overview and Context
This paper by Xiao Xiao and colleagues from Henan University of Science and Technology addresses a question I have wrestled with on more than one occasion: what actually happens to the microstructure of a 316L stainless steel deposit when you build it up layer by layer with a TIG torch? The authors used a φ1.0 mm 316L wire to produce single-pass, multi-layer straight-wall components, then examined the deposited layers with optical microscopy. Their central contribution is the distinction between two thermal accumulation regimes — non-equilibrium and equilibrium — and the resulting microstructural evolution in each.
For anyone who has run a wire-arc additive manufacturing (WAAM) cell, this is not an academic curiosity. The thermal history of each deposited layer is determined by the interpass temperature, the heat input, and the geometry of the part. Getting that wrong produces not just poor mechanical properties but, in the worst cases, unacceptable distortion, lack of fusion, or hot cracking. The paper gives us a systematic way to think about it.
Key Findings and Technical Interpretation
The authors describe two distinct thermal states. In the non-equilibrium state, heat accumulates rapidly and the cooling rate is high. In the equilibrium state, the interpass temperature stabilises and the cooling regime becomes more uniform. The microstructural observations are summarised below.
| Thermal state | Top of single layer | Bottom of single layer | Evolution mechanism |
|---|---|---|---|
| Non-equilibrium | Skeletal dendrites and equiaxed grains | Short dendrites | Increased heat accumulation changes undercooling; lower layers transform from skeletal ferrite to dendritic structure |
| Equilibrium | Dendrites and equiaxed grains | Short dendrites with some long dendrites | Transformation from dendrites to lath ferrite dominates |
The key point is that the final component microstructure is not what you would predict from a single-pass weld. The repeated thermal cycling from subsequent passes acts as an in-situ heat treatment. In the non-equilibrium case, the increased heat accumulation alters the undercooling during solidification, so the lower layers gradually change from skeletal ferrite to dendrites. In the equilibrium case, the dominant transformation is from dendritic structure to lath ferrite.
From a metallurgical standpoint, this is classic delta-ferrite behaviour in austenitic stainless steel. The ferrite morphology — skeletal, dendritic, or lath — is a direct function of the cooling rate and the peak temperature reached. Skeletal ferrite forms at high cooling rates, dendritic ferrite at intermediate rates, and lath ferrite at slow rates. The paper confirms that the thermal accumulation state effectively shifts the cooling rate experienced by each layer.
Practical Implications for Manufacturing and Quality Control
On the shop floor, this translates into three concrete rules of thumb.
- Control interpass temperature. If you are building a 316L component with TIG, do not let the interpass temperature drift upwards. The paper shows that non-equilibrium heat accumulation produces a microstructure that is not uniform through the wall. That means inconsistent mechanical properties and, more importantly, inconsistent corrosion resistance. For a component destined for a chemical plant or a marine environment, that is a non-negotiable requirement.
- Monitor the cooling regime. The transition from skeletal ferrite to lath ferrite is a signal that the cooling rate has dropped. If you see lath ferrite in the lower layers of a multi-pass deposit, you know the heat input is too high or the interpass time is too short. The fix is simple: increase the waiting time between passes or reduce the current.
- Expect anisotropy. The bottom of each layer cools differently from the top. In a multi-layer wall, this means the properties will vary through the thickness. If the design calls for a uniform structure, you need to either adjust the process parameters or plan a post-weld heat treatment (PWHT) to homogenise the structure.
I have seen components rejected because the microstructure was not what the customer expected. The usual culprit is a poorly controlled interpass temperature. This paper gives us the scientific basis to defend the process window.
Reflections and Lessons Learned
The authors have done a service to the welding community by quantifying the thermal accumulation effect. My own experience tells me that the practical takeaway is straightforward: treat the interpass temperature as a controlled process variable, not an afterthought. In production, we use thermocouples or infrared pyrometers to monitor the part temperature between passes. If the temperature exceeds a set limit, we stop and wait. It costs time, but it saves rework.
The paper also reminds me that additive manufacturing is not a "set and forget" process. The thermal history is cumulative, and the microstructure of the final part is the integrated result of every pass. For critical applications — pressure vessels, pipe fittings, structural nodes — I would insist on a full metallographic examination of the first article before releasing the process. The microstructural evolution described here is exactly the kind of thing that shows up in a cross-section.
In summary, this is a well-executed study that connects thermal behaviour to microstructure in a way that is directly usable on the plant floor. The next time you are setting up a TIG additive cell, remember: the interpass temperature is not just a number on a screen. It is the single most important variable controlling the final microstructure.
Zhuojin Pipe Fitting Co., Ltd