ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

TIG Brazing of AlSi5 Filler on Galvanized Steel: Wetting, Spreading, and Interface Behavior

Literature Overview and Technical Context

The paper by Shi Zhongxing et al. from Jiangsu University of Science and Technology examines the wetting and spreading behavior of AlSi5 filler on galvanized steel under TIG arc heating. The study also investigates the interface behavior between the filler and the substrate. The authors used scanning electron microscopy to observe the microstructure of the filler and the interface layer, measured the interface layer thickness, and used energy-dispersive X-ray spectroscopy to analyze the composition distribution across the interface.

The results show that as the arc time and current increase, the wetting angle of the AlSi5 filler on the galvanized steel decreases, and the spreading area increases. As the arc time increases, the thickness of the interface reaction layer increases. As the arc current increases, the interface layer thickness first increases and then decreases. The study found that at an arc current of 80 A alternating current and an arc time of 4 seconds, the interface layer contains the intermetallic compound Fe2Al5, and the intermetallic compound FeAl3 extends into the filler metal.

This is a fascinating study because it addresses the fundamental challenge of joining aluminum to steel. These two materials have vastly different melting points and are metallurgically incompatible. Direct fusion welding is not possible because the aluminum would melt before the steel, and the resulting joint would be brittle. TIG brazing is a viable alternative because it uses the TIG arc to heat the filler metal without melting the base material.

Interpretation of Technical Points and Process Analysis

The wetting and spreading behavior of the filler on the substrate is critical to the success of the brazing process. A low wetting angle and a large spreading area indicate good wetting, which is necessary for a sound joint. The study shows that increasing the arc time and current improves wetting, but there is a limit. If the arc time or current is too high, the filler metal may overheat and oxidize, leading to poor wetting.

The interface reaction layer is the key to the joint strength. The intermetallic compounds Fe2Al5 and FeAl3 are hard and brittle. A thin interface layer is desirable because it provides a metallurgical bond without compromising the joint ductility. However, if the interface layer is too thick, the joint becomes brittle and may fail under load.

The finding that the interface layer thickness first increases and then decreases with increasing arc current is particularly interesting. This suggests that at a certain current, the interface reaction is optimized. At lower currents, the reaction is limited by the temperature. At higher currents, the reaction may be limited by the availability of aluminum or iron at the interface.

The following table summarizes the key findings.

Arc Time Arc Current Wetting Angle Spreading Area Interface Layer Thickness Intermetallic Compounds
Increasing Constant Decreasing Increasing Increasing Fe2Al5, FeAl3
Constant Increasing Decreasing Increasing First increases, then decreases Fe2Al5, FeAl3

Engineering Practice Cases and Lessons Learned

TIG brazing of aluminum to steel is a process that I have seen used in the automotive industry for joining aluminum body panels to steel structures. The process is also relevant to the pipe and fitting industry for joining aluminum pipes to steel flanges or fittings. The key challenge is to control the heat input precisely so that the aluminum filler melts and wets the steel surface without melting the steel.

In my experience, the most common defect in TIG brazing is lack of wetting. This occurs when the steel surface is contaminated with oil, grease, or oxide. The galvanized coating on the steel can also be a problem. The zinc coating has a low melting point and can vaporize during the brazing process, creating porosity in the joint.

I recall a project where we were brazing aluminum tubes to steel headers for a heat exchanger. The contractor used a TIG brazing process with an AlSi5 filler. The initial welds showed poor wetting and a high porosity. We investigated the problem and found that the steel surface was contaminated with machining oil. After cleaning the surface with a solvent, the wetting improved dramatically, and the porosity was eliminated.

The lesson is that surface preparation is critical in TIG brazing. The steel surface must be clean and free from any contaminants. The galvanized coating should be removed if it is not required for corrosion protection, or the brazing parameters must be adjusted to account for the presence of zinc.

Key Questions and Reflections

The study raises an important question: what is the optimal interface layer thickness for a TIG brazed joint? The authors found that the interface layer contains Fe2Al5 and FeAl3, which are hard and brittle. A thin interface layer is desirable, but it must be thick enough to provide a metallurgical bond. In practice, the optimal thickness depends on the application.

For structural joints, a thin interface layer is preferred because it provides good strength without compromising ductility. For corrosion-resistant joints, a thin interface layer is also preferred because it minimizes the risk of galvanic corrosion. However, for joints that are subjected to thermal cycling, a thicker interface layer may be necessary to accommodate the differential thermal expansion between the aluminum and the steel.

Another important consideration is the effect of the galvanized coating on the interface. The zinc coating can react with the aluminum filler to form zinc-aluminum intermetallic compounds, which are even more brittle than the iron-aluminum compounds. This can lead to a significant reduction in joint strength.

Study Insights and Practical Recommendations

The paper by Shi Zhongxing et al. is a valuable contribution to the brazing literature. It provides a detailed analysis of the wetting and spreading behavior of AlSi5 filler on galvanized steel, and it identifies the intermetallic compounds that form at the interface. This information is essential for anyone who wants to use TIG brazing to join aluminum to steel.

For the shop floor, I recommend the following practical measures. First, ensure that the steel surface is clean and free from any contaminants. Second, remove the galvanized coating if it is not required for corrosion protection. Third, use a filler metal that is compatible with the base materials. Fourth, control the arc time and current to achieve the optimal interface layer thickness. Fifth, perform a bend test on the first production joint to verify that the brazing procedure is producing sound joints.

In conclusion, TIG brazing is a viable process for joining aluminum to steel, but it requires careful control of the process parameters. The wetting and spreading behavior of the filler is critical, and the interface reaction layer must be controlled to achieve the desired joint properties. The study by Shi Zhongxing et al. provides valuable data that can be used to optimize the process.