ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

TIG Welding of TC4 Titanium Alloy: Microstructure, Mechanical Properties, and Process Selection

Literature Overview

Chen, Liu, and Zhang (2021) conducted TIG welding experiments on 3.0 mm thick TC4 titanium alloy plates at different welding currents, then characterized the weld joints through metallography, tensile testing, fractography, and microhardness measurement. The results show that the weld bead appearance is satisfactory, the base metal consists of alpha and beta phases, the weld zone exhibits coarse acicular alpha-prime martensite, and the heat-affected zone (HAZ) contains a mixture of alpha-prime, alpha, and beta. The joint tensile strength is approximately 390 MPa, with fracture occurring in the weld zone. The fracture surface shows numerous small, shallow dimples, indicating ductile fracture. The weld zone has the highest hardness, decreasing from the weld center to the HAZ, then increasing toward the base metal. The overall mechanical properties are best at a welding current of 110 A.

Interpretation of Core Technical Points

Microstructural Evolution

The transformation from base metal alpha+beta to weld zone acicular alpha-prime is a direct consequence of the rapid cooling rate in TIG welding. The beta phase in the base metal transforms to martensitic alpha-prime upon rapid cooling, resulting in a fine acicular structure. The HAZ experiences a partial transformation, with some alpha-prime forming in the beta regions, while the alpha grains remain largely unchanged. The coarse grain size in the weld zone is a result of the high peak temperature and the absence of grain refinement mechanisms in the fusion zone.

Mechanical Properties and Fracture Behavior

The tensile strength of approximately 390 MPa is lower than typical values for TC4 base metal (which is usually in the 900–1000 MPa range for annealed material). This significant reduction is due to the coarse grain structure in the weld zone and the presence of alpha-prime martensite, which is harder but less ductile than the base metal. The fracture location in the weld zone confirms that this is the weakest region of the joint. The ductile fracture mode, evidenced by dimples, indicates that the weld metal retains some ductility despite the martensitic structure.

Effect of Welding Current

Welding Current (A) Weld Appearance Tensile Strength (MPa) Fracture Location Hardness Trend
Below 110 Shallow penetration, undercut risk Lower than optimum Weld zone Non-uniform
110 Good appearance, full penetration ~390 MPa Weld zone Weld > HAZ > Base
Above 110 Excessive penetration, burn-through risk May decrease due to grain growth Weld zone Higher weld hardness

Integration with Engineering Practice

Titanium welding is unforgiving. The high reactivity of titanium with oxygen, nitrogen, and hydrogen at elevated temperatures means that the shielding gas must be of high purity (99.99% argon minimum) and the weld must be shielded on both the top and bottom surfaces. In our shop, we have seen weld discoloration—a sign of contamination—when the trailing shield is not properly positioned or when the back purge is insufficient. The paper's finding that the weld zone is the weakest link is consistent with our experience. For titanium pipe used in aerospace or chemical applications, the weld joint efficiency is often the limiting factor in the design.

Key Questions and Reflections

The paper does not address the effect of post-weld heat treatment (PWHT) on the weld joint properties. In many applications, TC4 weldments are stress-relieved or annealed to reduce residual stresses and improve ductility. The question is whether PWHT can improve the weld zone properties enough to bring the joint strength closer to the base metal. In our experience, PWHT at 600–700°C for 1–2 hours can reduce the hardness of the weld zone and improve ductility, but the strength may decrease further. The optimum PWHT schedule must be determined for each application.

Study Insights and Implications

The key insight is that the welding current must be selected carefully to balance penetration and heat input. Too low a current results in incomplete penetration, while too high a current causes grain growth and potential burn-through. The paper's finding that 110 A is optimal for 3.0 mm TC4 provides a useful starting point, but the actual current must be adjusted based on joint design, fit-up, and welding position. In pipe welding, the current may need to be reduced for overhead positions to prevent the weld pool from sagging.

Reference Value and Outlook

This work provides a solid foundation for TIG welding of TC4 titanium alloy. The next step in our practice is to validate the process on actual pipe joints with full mechanical testing, including bend tests and impact tests at low temperature, to ensure the weld joint meets the requirements of ASME B31.3 for titanium piping. The process shows promise for aerospace and chemical applications, but requires careful validation.