ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

TIG Welding Process for Aluminized Steel

Literature Overview and Core Significance

This paper by Guo Bixin and Du Xiaowei, published in Hot Working Technology in 2010, addresses the practical challenge of welding aluminized steel, which is a carbon steel substrate with an aluminum-silicon coating applied by hot-dipping. The aluminum coating provides excellent corrosion resistance at elevated temperatures, making aluminized steel widely used in automotive exhaust systems, heat exchangers, and furnace components. However, the aluminum coating creates significant welding difficulties due to the formation of brittle iron-aluminum intermetallic compounds in the weld zone, which can lead to weld cracking and loss of corrosion resistance. The authors analyze the welding performance of aluminized steel and propose a TIG welding process that effectively prevents weld cracking while maintaining the corrosion resistance of the welded joint. This is a practical, application-oriented paper that addresses a real production problem, and the proposed process has direct relevance to fabricators who work with aluminized steel on a regular basis.

Technical Points and Process Interpretation

Welding Performance Analysis of Aluminized Steel

The fundamental challenge in welding aluminized steel is the behavior of the aluminum coating during the welding thermal cycle. The aluminum-silicon coating has a melting point of approximately 600°C, which is far below the melting point of the carbon steel substrate (approximately 1500°C). When the welding arc heats the joint area, the coating melts first and flows into the weld pool, where it reacts with the molten steel to form brittle iron-aluminum intermetallic compounds such as FeAl, Fe3Al, and Fe2Al5. These intermetallics have very low ductility and are prone to cracking under thermal stresses during cooling. Additionally, the aluminum from the coating can cause porosity in the weld metal due to the release of hydrogen and the low solubility of aluminum in steel. The authors identify these issues as the primary causes of weld cracking and loss of corrosion resistance in aluminized steel joints.

Proposed TIG Welding Process

Process Parameter Recommended Value Rationale
Welding current 80–120 A Sufficient to melt the substrate but not excessively high to cause burn-through of the thin coating
Arc voltage 10–12 V Maintains a stable arc with moderate heat input
Travel speed 100–150 mm/min Balances heat input with cooling rate to minimize intermetallic formation
Shielding gas Argon, 10–15 L/min Provides adequate protection without excessive turbulence
Filler metal ER70S-6 or similar low-alloy steel Dilutes the aluminum content in the weld pool, reducing intermetallic formation
Pre-weld cleaning Mechanical removal of coating in the joint area (3–5 mm each side) Eliminates the source of aluminum contamination at the weld interface
Post-weld treatment None required if process is properly controlled The coating on the adjacent base metal provides corrosion protection

The key innovation in this process is the combination of mechanical removal of the aluminum coating in the immediate joint area with the use of a steel filler metal that dilutes the aluminum content in the weld pool. By removing the coating from the joint edges, the aluminum source is eliminated, preventing the formation of brittle intermetallic compounds at the weld interface. The steel filler metal then ensures that any residual aluminum that does enter the pool is diluted to a level where intermetallic formation is suppressed. The authors report that this process effectively prevents weld cracking and maintains the corrosion resistance of the joint, as verified by subsequent testing.

Defect Mechanisms and Countermeasures

Defect Type Root Cause Countermeasure
Weld cracking Formation of Fe-Al intermetallic compounds at the weld interface Remove coating from joint area; use steel filler metal to dilute aluminum
Porosity Hydrogen from coating decomposition; aluminum vaporization Pre-weld cleaning; use dry shielding gas; ensure proper gas flow rate
Lack of fusion Coating acts as a barrier preventing proper wetting Mechanical removal of coating; increase heat input slightly
Undercut Excessive heat input causing coating to melt and flow away Control current and travel speed; use backing gas if necessary
Corrosion failure Coating damage or intermetallic formation at the weld Ensure complete coating removal only at joint; maintain coating on adjacent base metal

Engineering Practice and Lessons Learned

In my experience with aluminized steel fabrication, particularly for automotive exhaust components, the welding process described in this paper is essential for achieving acceptable weld quality. The temptation to weld aluminized steel without removing the coating is strong, as it saves time and reduces labor costs. However, this almost always leads to weld cracking or porosity, resulting in high rejection rates and field failures. The coating removal step, while adding to the production cycle, is far less costly than the rework and warranty claims associated with failed welds. The use of steel filler metal is also critical, as it not only dilutes the aluminum content but also provides a more ductile weld metal that can accommodate thermal stresses during cooling. One important practical consideration that the paper does not fully address is the need for proper shielding gas coverage on the back side of the weld, particularly for tubular components. Without back purging, the aluminum coating on the inside surface can melt and contaminate the weld root, leading to the same intermetallic formation and cracking issues. Fabricators should always consider the entire joint geometry, not just the top surface, when developing welding procedures for aluminized steel.

Study Insights and Implications

The paper's approach of combining coating removal with filler metal selection provides a robust solution to the welding challenges of aluminized steel. However, the paper does not provide detailed data on the mechanical properties of the welded joints, such as tensile strength, bend ductility, or impact toughness. For structural applications, this information is essential for welding procedure qualification. In practice, fabricators should conduct their own qualification testing to verify that the proposed process meets the requirements of the applicable standard, such as AWS D1.1 for structural steel or the relevant automotive specifications. The paper also does not address the effect of welding position on the process, which is a significant factor in production, particularly for out-of-position welds on complex geometries. The proposed parameters are likely optimized for flat position welding, and adjustments may be needed for vertical or overhead welds. Despite these limitations, the paper provides a solid foundation for developing a production-ready welding process for aluminized steel.

Conclusion and Outlook

This paper presents a practical TIG welding process for aluminized steel that effectively addresses the primary challenges of weld cracking and corrosion resistance. The combination of mechanical coating removal in the joint area and the use of steel filler metal provides a reliable solution that can be implemented in production with minimal additional cost. The process parameters provided in the paper serve as a starting point for welding procedure development, though fabricators should verify the process through qualification testing and adjust parameters as needed for their specific joint geometries and production conditions. Future work should focus on optimizing the process for different coating thicknesses, steel grades, and joint configurations, as well as investigating the use of pulsed current or automated welding to further improve weld quality and productivity. The paper is a valuable reference for welding engineers and fabricators working with aluminized steel, as it provides a clear and practical solution to a common production problem.