ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

TIG Welding of CNTs/Al Composites: Weld Formation and Microstructure

Literature Overview and Core Message

The 2013 paper from Nanchang Hangkong University investigates the TIG welding of carbon nanotube (CNT) reinforced aluminium matrix composites. The authors use optical microscopy, scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), and X-ray diffraction (XRD) to characterise the weld microstructure and phase composition. They also use electron work function analysis to assess the distribution uniformity of CNTs in the weld. The key findings are that good weld surface formation can be achieved with an argon shielding box, but the presence of CNTs degrades the weldability of the composite. The molten pool has poor fluidity, leading to porosity and cracking. CNTs react with the aluminium matrix to form Al4C3, and the CNTs are partially burned out and unevenly distributed in the weld.

Technical Interpretation: The Challenges of Welding CNT-Reinforced Composites

Why CNTs/Al Composites Are Difficult to Weld

CNT-reinforced aluminium matrix composites are a class of advanced materials with high specific strength and stiffness. However, their weldability is poor for several reasons. First, CNTs have a high thermal conductivity, which can cause rapid heat dissipation from the weld pool, leading to poor fusion. Second, CNTs can react with aluminium to form Al4C3, a brittle intermetallic compound that degrades the mechanical properties of the joint. Third, the CNTs can be burned out during welding, losing the reinforcement effect. Finally, the CNTs reduce the fluidity of the molten pool, making it difficult to achieve a uniform weld bead.

The Role of Al4C3 Formation

The formation of Al4C3 is a critical issue. Al4C3 is a needle-like, brittle phase that forms at the CNT-aluminium interface. It acts as a stress concentrator, reducing the toughness and ductility of the joint. The paper confirms the presence of Al4C3 in the weld, which is a significant finding. The amount of Al4C3 depends on the welding heat input and the reaction time. Higher heat input promotes Al4C3 formation, so the welding parameters must be carefully controlled to minimise this reaction.

Porosity and Cracking

The paper reports that porosity and cracking are common defects in CNTs/Al composite welds. The porosity is likely caused by the poor fluidity of the molten pool, which prevents gas bubbles from escaping. The cracking is likely caused by the presence of Al4C3 and the thermal stresses generated during welding. These defects are serious and can lead to joint failure.

Electron Work Function Analysis

The use of electron work function analysis to assess CNT distribution is a novel approach. The electron work function is sensitive to the presence of CNTs, so variations in the work function across the weld indicate non-uniform CNT distribution. The paper reports that the CNTs are unevenly distributed in the weld, which is expected given the poor fluidity of the molten pool.

Engineering Practice: Practical Considerations for Welding Metal Matrix Composites

Shielding Gas and Protection

The paper uses an argon shielding box to protect the weld. This is essential for aluminium welding, as aluminium is highly reactive and forms a tenacious oxide layer. The shielding box provides a more effective barrier than a conventional shielding gas nozzle, ensuring that the weld is fully protected. In practice, a shielding box is used for high-quality aluminium welds, particularly in aerospace applications.

Joint Preparation

The joint preparation is critical for CNTs/Al composites. The surfaces must be clean and free of oxide. The composite material is often difficult to machine, so the joint preparation must be carefully planned. The paper does not discuss joint preparation in detail, but it is an important practical consideration.

Welding Parameter Selection

The welding parameters must be carefully selected to minimise Al4C3 formation and porosity. Lower heat input reduces Al4C3 formation but may lead to lack of fusion. Higher heat input improves fusion but promotes Al4C3 formation and porosity. The optimal parameters are a compromise between these competing factors.

Comparison with Conventional Aluminium

Parameter CNTs/Al Composite Conventional Aluminium
Weld pool fluidity Poor Good
Porosity risk High Low
Cracking risk High Low
Interface reaction Al4C3 formation None
Reinforcement retention Partial burn-out N/A
Weldability Poor Good

Key Questions and Reflections

  1. Is there a way to avoid Al4C3 formation? Al4C3 formation is thermodynamically favourable, so it is difficult to avoid entirely. However, it can be minimised by using lower heat input and shorter welding times. The use of a filler wire that does not react with CNTs may also help.
  2. What about post-weld heat treatment? Post-weld heat treatment could potentially modify the Al4C3 morphology, but it may also cause grain growth and reduce the mechanical properties of the composite. This is an area for further research.
  3. Is TIG welding the best process for this material? TIG welding provides good control of heat input, but the poor fluidity of the molten pool is a fundamental limitation. Other processes, such as laser welding or electron beam welding, may offer better control of the weld pool and reduce porosity. However, these processes are more expensive and may not be suitable for all applications.

Study Insights and Implications

This paper highlights the significant challenges of welding CNT-reinforced aluminium matrix composites. The poor fluidity of the molten pool, the formation of Al4C3, and the burn-out of CNTs are fundamental issues that limit the weldability of this material. The paper provides a thorough characterisation of the weld microstructure and identifies the key mechanisms of defect formation.

The practical lesson is that CNTs/Al composites are not currently suitable for welding in structural applications. The defects and the degradation of the reinforcement make the joints unreliable. However, the paper provides valuable insights into the failure mechanisms, which can guide future research. If the Al4C3 formation can be controlled and the CNT distribution can be improved, the weldability of this material could be significantly enhanced.

For pipe and fitting fabrication, CNTs/Al composites are not yet a practical material. The welding challenges are too significant, and the material is too expensive for most applications. However, as the technology matures, it may find use in specialised applications where the high specific strength and stiffness of the composite are critical. The paper is a valuable contribution to the understanding of this emerging material.