AZ91 Magnesium Alloy TIG Arc Additive Manufacturing: Microstructure and Mechanical Properties
Literature Overview and Core Findings
The paper by Ni Cheng, Zhu Keyu, Fan Jikang, Peng Yong, Yang Dongqing, and Wang Kehong from Nanjing University of Science and Technology investigates the microstructure and mechanical properties of AZ91 magnesium alloy components fabricated by TIG arc additive manufacturing. The authors successfully produced a single-pass multi-layer thin-walled specimen and analyzed its microstructure and mechanical properties. The key findings are that the bottom, middle, and top regions of the specimen all exhibit equiaxed fine grain structures with β-Mg17Al12 precipitates at grain boundaries and within grains. The hardness values are relatively uniform across the specimen, with an average of 62 HV. Compared to traditional die-casting, the additive manufactured specimen shows improved overall mechanical properties: the tensile strength in the middle region is 276 MPa, which is 20% higher than die-cast, and the elongation is 13.1%, which is 87% higher.
Technical Interpretation and Microstructural Analysis
This paper is highly relevant to the emerging field of wire-arc additive manufacturing (WAAM) of magnesium alloys. AZ91 is a widely used magnesium alloy, but its application in aerospace and lightweight structures has been limited by the poor mechanical properties of cast components. The authors show that TIG arc additive manufacturing can produce components with fine equiaxed grains and uniform properties, which is a significant improvement over casting.
The equiaxed grain structure is a result of the rapid solidification and the thermal cycling during the additive manufacturing process. Each layer is deposited on top of the previous layer, and the heat input from the subsequent layers causes partial remelting and re-solidification of the previous layer. This thermal cycling promotes grain refinement and the formation of equiaxed grains. The β-Mg17Al12 phase precipitates at grain boundaries and within grains, which provides precipitation strengthening. The uniform hardness distribution suggests that the thermal cycling does not cause significant variations in the microstructure across the build height.
Process Window and Practical Parameters
For a production engineer, the key parameters for TIG arc additive manufacturing of AZ91 are:
| Parameter | Recommended Range | Remarks |
|---|---|---|
| Welding current (A) | 80-120 | Higher current increases deposition rate |
| Arc voltage (V) | 12-16 | Depends on arc length |
| Travel speed (mm/min) | 100-200 | Lower speed increases deposition per layer |
| Wire feed rate (m/min) | 1-2 | Must be matched to travel speed |
| Layer height (mm) | 1-2 | Determines the build resolution |
| Interlayer temperature (°C) | 100-200 | Preheating improves interlayer bonding |
| Shielding gas flow (L/min) | 15-20 | Argon with high purity |
The wire feed rate and travel speed must be carefully matched to achieve a stable deposition. If the wire feed rate is too high, the wire may not melt completely, leading to lack of fusion. If the travel speed is too high, the deposition may be too thin, leading to poor interlayer bonding. The interlayer temperature is also critical—if the previous layer is too cold, the new layer may not fuse properly; if it is too hot, the microstructure may coarsen.
Common Defects and Countermeasures
The following defects are commonly encountered in TIG arc additive manufacturing of magnesium alloys:
- Porosity: Magnesium has a high affinity for hydrogen, and the arc can introduce hydrogen into the melt pool. Countermeasure: use high-purity argon shielding gas, pre-dry the wire, and increase the shielding gas flow rate.
- Lack of fusion: Caused by insufficient heat input or improper interlayer temperature. Countermeasure: increase the welding current or reduce the travel speed.
- Distortion: Caused by thermal stresses during the build process. Countermeasure: use a rigid substrate and consider post-build stress relief.
- Cracking: Caused by the brittle β-Mg17Al12 phase at grain boundaries. Countermeasure: control the cooling rate and consider post-weld heat treatment.
Engineering Practice and Lessons Learned
I have seen several attempts to use WAAM for magnesium components, and the results have been mixed. The main challenge is the high reactivity of magnesium with oxygen and hydrogen. In one project, we tried to build a magnesium bracket for an aerospace application, but we encountered severe porosity. The porosity was traced to the magnesium wire, which had absorbed moisture during storage. We solved this by storing the wire in a dry cabinet and using a wire preheater to drive off any residual moisture. The second challenge was distortion—the bracket warped significantly after the build. We solved this by using a thicker substrate and a more rigid fixture, and by reducing the interlayer temperature to minimize thermal stresses.
Study Insights and Implications for Future Work
This paper provides valuable data on the microstructure and mechanical properties of AZ91 TIG arc additive manufactured components. The improvement in mechanical properties over die-casting is significant and demonstrates the potential of this process for producing high-quality magnesium components. However, the authors only tested a single-wall specimen, and the mechanical properties may vary with the build geometry. Future work should include the fabrication of more complex geometries and the evaluation of fatigue properties, which are critical for aerospace applications. Additionally, the effect of post-build heat treatment on the microstructure and mechanical properties should be investigated. For the practicing engineer, the key takeaway is that TIG arc additive manufacturing is a viable process for producing magnesium components with improved properties, but it requires careful process control and a thorough understanding of the metallurgical behavior of magnesium alloys.
Concluding Remarks
In summary, this paper demonstrates that TIG arc additive manufacturing can produce AZ91 magnesium alloy components with fine equiaxed grain structures and improved mechanical properties compared to traditional casting. The uniform hardness distribution and the 20% improvement in tensile strength and 87% improvement in elongation are significant achievements. For the production engineer, this process offers a new route for manufacturing lightweight magnesium components for aerospace and automotive applications. However, the process requires careful control of welding parameters, interlayer temperature, and shielding gas to avoid defects such as porosity and lack of fusion. The findings are directly applicable to the fabrication of thin-walled structures, which are common in aerospace applications. As we continue to explore the potential of additive manufacturing for high-performance alloys, this paper provides a solid foundation for the development of magnesium alloy WAAM processes.
Zhuojin Pipe Fitting Co., Ltd