ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

TIG-Drawn Arc Hybrid Heat Source for Aluminum Alloy Stud Welding

Literature Overview and Practical Significance

This paper by Zhang Deku, Wang Yan, Wang Kehong and Kang Lulu tackles a problem that has cost me many sleepless nights: welding large-diameter aluminum studs to aluminum plates. The authors studied 16 mm diameter studs, which is a size that is notoriously difficult to weld because the heat input required to melt the stud base and the plate surface creates a large molten pool that is prone to porosity, lack of fusion and hot cracking. The authors proposed a TIG-drawn arc hybrid heat source, which is an elegant solution. The TIG arc preheats the plate surface and creates a shallow weld pool, while the drawn arc provides the high energy density needed to melt the stud base and fuse it into the pool. The studs were pre-coated with a zinc-nickel layer, and the entire process was carried out under inert gas shielding. The results show a joint shear strength of 128 MPa, which is a strength coefficient of over 70% relative to the base metal. The optimal parameters were preheating at 150°C, welding current of 650 A and welding time of 1000 ms. This is a significant improvement over conventional drawn arc stud welding, which typically gives a strength coefficient of 50 to 60% for aluminum studs. The paper is a practical guide for anyone who has to weld aluminum studs in a production environment, whether for shipbuilding, heat exchanger fabrication or electrical equipment.

Key Technical Parameters and Process Window

The authors systematically varied the preheating temperature, welding current and welding time, and the optimal parameters are summarized below.

Parameter Value Remarks
Stud diameter 16 mm Medium-to-large diameter
Preheating temperature 150°C Applied to the plate surface
Welding current 650 A Drawn arc current
Welding time 1000 ms Arc duration
Stud surface treatment Zinc-nickel pre-coating Applied before welding
Shielding gas Inert gas Argon or helium, not specified in detail
Joint shear strength 128 MPa Strength coefficient over 70%
Preheating method TIG arc Creates a shallow molten pool before stud welding

The preheating temperature of 150°C is critical. Aluminum has a high thermal conductivity, so without preheating, the heat from the drawn arc is rapidly conducted away from the joint, leaving a shallow penetration and a high risk of lack of fusion. Preheating to 150°C reduces the temperature gradient and allows the weld pool to form properly. The welding current of 650 A is high, but it is necessary for a 16 mm stud. The welding time of 1000 ms is long enough to allow the stud base to melt and fuse with the plate, but short enough to avoid excessive melting of the stud, which would cause it to collapse. The zinc-nickel pre-coating is an interesting innovation. Zinc has a low melting point and a high vapor pressure, so it tends to vaporize during welding and create porosity. However, when combined with nickel, the zinc-nickel alloy has a higher melting point and a lower vapor pressure, which reduces the porosity. The nickel also improves the wetting of the molten aluminum on the stud surface. The authors found that the pre-coating improved both the joint strength and the weld microstructure.

Microstructural Interpretation and Defect Analysis

The paper addresses three common defects in aluminum stud welding: porosity, lack of fusion and hot cracking. Porosity is caused by hydrogen, which is soluble in molten aluminum but precipitates as gas bubbles during solidification. The hydrogen comes from moisture on the stud surface, the plate surface or the shielding gas. The authors addressed this by pre-coating the stud with zinc-nickel, which reduces the amount of moisture that can be absorbed, and by using inert gas shielding, which prevents atmospheric moisture from entering the weld pool. The zinc-nickel coating also acts as a flux, which helps to remove oxides from the stud surface. Lack of fusion is caused by insufficient heat input or by the presence of a thick oxide layer on the aluminum surface. The TIG preheating step addresses this by melting the plate surface and creating a shallow pool before the drawn arc is applied. The oxide layer on aluminum melts at about 2050°C, which is much higher than the melting point of aluminum at 660°C. If the oxide layer is not broken up, the molten aluminum will not wet the surface and you get lack of fusion. The TIG arc, with its high temperature and its cathodic cleaning action, breaks up the oxide layer and allows the stud to fuse with the plate. Hot cracking is caused by the wide solidification range of aluminum alloys and the presence of low-melting-point eutectic phases at the grain boundaries. The authors found that the TIG preheating reduces the cooling rate, which gives the eutectic phases more time to redistribute and reduces the risk of hot cracking. The zinc-nickel coating also helps by modifying the solidification path.

Engineering Practice and Lessons Learned

In my experience with aluminum stud welding, the two biggest causes of failure are poor surface preparation and inadequate shielding. The authors addressed both. The zinc-nickel pre-coating is a good idea, but it adds a process step that must be controlled. The coating thickness must be uniform, and the coating must be applied to a clean, degreased surface. If the coating is too thick, it will not fully dissolve in the weld pool and will leave inclusions. If it is too thin, it will not provide adequate protection. I would recommend a coating thickness in the range of 5 to 10 microns. The shielding gas is also critical. The authors used inert gas shielding, but they did not specify whether it was argon or helium. For aluminum, helium gives a hotter arc and deeper penetration, but argon is cheaper and gives a more stable arc. For a 16 mm stud, I would use a mixture of 70% helium and 30% argon, which gives a good balance of penetration and stability. The welding time of 1000 ms is a critical parameter. If the welding time is too short, the stud base will not fully melt and you get lack of fusion. If it is too long, the stud will overheat and collapse, or you will get excessive melting of the plate. The 1000 ms value is a good starting point, but it must be tuned to the specific stud diameter, plate thickness and alloy composition. The preheating temperature of 150°C is also critical. If the preheating is too low, the heat from the drawn arc will be conducted away too quickly. If it is too high, you risk distorting the plate or causing the stud to sink. I would recommend using a thermocouple to monitor the plate temperature during preheating and ensuring that the temperature is uniform across the weld area.

Critical Assessment and Study Insights

The paper is a valuable contribution to the field of aluminum stud welding, but there are a few points I would raise. First, the authors did not report the results of a metallographic examination of the weld joint. A cross-section would show whether the fusion zone is complete and whether there are any cracks or porosity. This is essential for a full understanding of the joint quality. Second, the authors did not report the hardness of the weld joint. In aluminum stud welding, the HAZ is often softened by the heat input, which can reduce the joint strength. A hardness survey would reveal whether this is a concern. Third, the paper does not report the results of a fatigue test. For many applications, such as studs on ship decks or on heat exchanger tube sheets, the joint is subjected to cyclic loading, and fatigue is the critical failure mode. The static shear strength of 128 MPa is good, but it does not tell you how the joint will behave under cyclic loading. Fourth, the paper does not discuss the effect of the stud alloy composition. The authors used an unspecified aluminum alloy, but the welding behavior varies significantly between 5000 series and 6000 series alloys. The 6000 series alloys are more prone to hot cracking, while the 5000 series alloys are more prone to porosity. Despite these gaps, the paper provides a solid foundation for process development. The TIG-drawn arc hybrid heat source is a clever approach that addresses the fundamental problem of heat input distribution in aluminum stud welding.

Reference Value and Practical Outlook

This paper is a useful reference for anyone developing a welding procedure for aluminum studs. The TIG-drawn arc hybrid heat source is a significant improvement over conventional drawn arc stud welding, and the zinc-nickel pre-coating is an effective way to reduce porosity and improve joint quality. The optimal parameters of 150°C preheating, 650 A welding current and 1000 ms welding time are a good starting point for a 16 mm stud, but they must be tuned to the specific application. I would recommend that any welding procedure qualification for aluminum studs include a metallographic examination, a hardness survey and a fatigue test. The metallographic examination will confirm that the fusion zone is complete and that there are no cracks or porosity. The hardness survey will reveal whether the HAZ is softened. The fatigue test will confirm that the joint can withstand cyclic loading. In my experience, the best way to verify the joint quality is to cut a stud in half, polish the cross-section and examine it under a microscope. If you see a complete fusion zone with no cracks or porosity, the joint is good. If you see any lack of fusion or porosity, the process parameters must be adjusted. This paper gives you the tools to do that, and the rest is a matter of discipline and attention to detail on the shop floor.