Stainless Steel TIG Braze-Welding Joint Microstructure and Mechanical Properties
Overview and Relevance to Dissimilar Metal Joining
This paper from Harbin Institute of Technology, published in 2008, investigates the TIG braze-welding of stainless steel using high-temperature copper-based filler wires S211 and S201. The process is a hybrid of fusion welding and brazing, which is a technique I have used for joining stainless steel to copper or to itself where a low-heat-input process is required. The relevance to our industry is in the production of transition joints for cryogenic piping, heat exchanger tube sheets, and electrical components where the joint must be leak-tight and have good mechanical properties without excessive distortion.
Key Technical Findings and Joint Characteristics
The authors used a high-temperature copper-based filler wire to join stainless steel. The process is called "braze-welding" because it combines characteristics of both fusion welding and brazing. The key findings are summarized below.
| Aspect | S211 Filler Wire | S201 Filler Wire |
|---|---|---|
| Joint type | Hybrid fusion-brazing | Hybrid fusion-brazing |
| Upper part of joint | Fusion zone with α+ε phase | Fusion zone with α+ε phase |
| Lower part of joint | Brazed joint, no base metal melting | Brazed joint, no base metal melting |
| Weld matrix | Fe supersaturated solid solution in Cu | Fe supersaturated solid solution in Cu |
| Tensile strength | 498.33 MPa | 476.67 MPa |
| Elongation | 13.8% | 19.6% |
| Fracture location | Weld zone | Weld zone |
The hybrid nature of the joint is the key to understanding its performance. In the upper part, near the arc, the stainless steel melts and mixes with the copper filler, forming a fusion zone with a complex α+ε phase structure. In the lower part, the stainless steel remains solid, and the copper filler wets and bonds to it, forming a brazed joint. This dual nature means that the joint has a gradual transition from a metallurgical bond to a mechanical bond, which is beneficial for reducing stress concentrations.
Microstructure and Phase Analysis
The microstructure of the joint is complex. The weld matrix is a supersaturated solid solution of iron in copper, which is a metastable phase. On this matrix, there are numerous α+ε phase particles of varying sizes. The α phase is iron-rich, and the ε phase is a copper-rich intermetallic compound.
| Region | Microstructure | Comment |
|---|---|---|
| Weld upper part | Many α+ε particles, fine distribution | High temperature near arc promotes nucleation |
| Weld lower part | Fewer α+ε particles, coarser | Lower temperature, slower cooling |
| Fusion zone (upper) | α+ε eutectic structure | Base metal partially melted |
| Brazed zone (lower) | Clean interface, no base metal melting | Good wetting and bonding |
The difference in particle distribution between the upper and lower parts of the weld is a result of the different cooling rates. The upper part cools faster due to the arc, which promotes fine, numerous particles. The lower part cools slower, allowing the particles to grow and coalesce. This is a classic example of how the thermal cycle determines the final microstructure.
Mechanical Properties and Filler Wire Selection
The mechanical properties show a clear trade-off between strength and ductility. S211 gives higher strength (498.33 MPa) but lower elongation (13.8%). S201 gives lower strength (476.67 MPa) but higher elongation (19.6%). This is a classic example of the strength-ductility trade-off in welding.
| Filler Wire | Tensile Strength (MPa) | Elongation (%) | Application Suitability |
|---|---|---|---|
| S211 | 498.33 | 13.8 | High-strength joints, limited ductility |
| S201 | 476.67 | 19.6 | High-ductility joints, moderate strength |
Both joints fractured in the weld zone, which is expected for a braze-welded joint. The weld zone is the weakest link because it contains the brittle α+ε phase particles. The higher strength of S211 is likely due to a higher iron content in the filler wire, which provides more solid solution strengthening. The higher elongation of S201 is due to a higher copper content, which provides more ductility.
Practical Implications for Production and Design
For our shop floor, this paper provides valuable guidance on the selection of filler wire for braze-welding stainless steel.
- Joint design: The braze-welding process is best suited for joints where the base metal is thin and the heat input must be minimized. For thicker sections, the process may not provide adequate penetration. We have used this process for tube-to-tube sheet joints in heat exchangers, where the tube is thin and the tube sheet is thick.
- Filler wire selection: The choice between S211 and S201 depends on the service requirements. If the joint is in a high-stress application, S211 is preferred. If the joint is in a corrosive environment or requires high ductility, S201 is preferred. In my experience, the ductility of the joint is often more important than the strength, especially for joints that will undergo thermal cycling.
- Process control: The braze-welding process is sensitive to the arc length and travel speed. A short arc is essential to ensure that the copper filler wets the stainless steel surface. A long arc will overheat the filler and cause it to vaporize. We typically use a precise arc length control system to maintain a consistent joint quality.
- Inspection: The joint should be inspected for lack of wetting and porosity. Lack of wetting is a common defect in braze-welding, and it can lead to leaks. We use dye penetrant testing (PT) for surface defects and ultrasonic testing (UT) for internal defects.
Critical Questions and Personal Reflection
The paper does not address the corrosion resistance of the joint. In a stainless steel-copper joint, the galvanic couple between the copper and the stainless steel is a concern. The copper will act as a cathode and the stainless steel as an anode, which can lead to localized corrosion of the stainless steel. This is a serious issue for marine applications.
Another question is the fatigue behavior. The α+ε phase particles are brittle, and they can act as crack initiation sites under cyclic loading. The fatigue strength of the joint is likely to be lower than that of the base metal. This needs to be evaluated for any application involving cyclic loading.
Study Insights and Outlook
This paper is a good example of how a hybrid process can be used to join dissimilar metals. The braze-welding process offers a unique combination of fusion and brazing, which can be tailored to specific applications. The key is to understand the relationship between the process parameters, the microstructure, and the mechanical properties.
For our industry, the lesson is that we should not limit ourselves to conventional welding or brazing. Hybrid processes like braze-welding can offer significant advantages in terms of joint quality and process flexibility. The selection of the filler wire is critical, and it should be based on the service requirements, not just the cost. The S211 wire provides higher strength, while the S201 wire provides higher ductility. The choice is a trade-off that must be made with a full understanding of the service conditions. The next step in our development should be to evaluate the corrosion and fatigue behavior of these joints to ensure they meet the requirements for long-term service.
Zhuojin Pipe Fitting Co., Ltd