ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Microstructure and Mechanical Properties of AZ31 Magnesium Alloy TIG Welded Joints Under Different Heat Inputs

Introduction and Literature Context

The paper by Liao Huimin and colleagues from Xihua University, published in Mechanical Engineering Materials in 2017, investigates the effect of welding heat input on the microstructure and mechanical properties of AZ31 magnesium alloy TIG welded joints. The authors used AC TIG welding to join 2 mm thick hot-rolled AZ31 magnesium alloy sheets under different heat inputs. They examined the microstructure using microscopy, measured the hardness, and conducted tensile tests. The key findings are:

  1. The base metal has a single-phase α-Mg solid solution structure.
  2. The heat affected zone and the weld zone have a structure of α-Mg solid solution with dispersed β-Mg17Al12 phase.
  3. As the heat input increases, the grain size in the weld zone increases, and the amount of β-Mg17Al12 phase increases.
  4. The weld zone has the highest hardness, followed by the base metal, with the heat affected zone having the lowest hardness.
  5. As the heat input increases, the tensile strength of the welded joint first increases and then decreases, reaching a maximum of 223 MPa at 90 A, which is 89.2% of the base metal strength. The elongation at this point is 10.0%.
  6. The tensile fracture occurs mainly in the heat affected zone, and the fracture mode is quasi-cleavage fracture.

This paper is of direct relevance to my work. In the fabrication of magnesium alloy components, such as the housings of aerospace equipment and the casings of automotive parts, we frequently use TIG welding. The control of the heat input is critical to achieving the desired microstructure and mechanical properties.

Core Technical Findings and Their Practical Significance

The paper's most significant contribution is the demonstration that the welding heat input has a profound effect on the microstructure and mechanical properties of AZ31 magnesium alloy TIG welded joints. The key findings are:

  1. Microstructure: The base metal has a single-phase α-Mg solid solution structure. The heat affected zone and the weld zone have a structure of α-Mg solid solution with dispersed β-Mg17Al12 phase. As the heat input increases, the grain size in the weld zone increases, and the amount of β-Mg17Al12 phase increases. This is because the higher heat input results in a slower cooling rate, which allows more time for the β-Mg17Al12 phase to precipitate.
  2. Hardness: The weld zone has the highest hardness, followed by the base metal, with the heat affected zone having the lowest hardness. The high hardness in the weld zone is due to the presence of the β-Mg17Al12 phase, which is a hard intermetallic compound. The low hardness in the heat affected zone is due to the grain growth that occurs during the welding thermal cycle.
  3. Tensile Strength: As the heat input increases, the tensile strength of the welded joint first increases and then decreases, reaching a maximum of 223 MPa at 90 A, which is 89.2% of the base metal strength. The initial increase in tensile strength is due to the increased amount of β-Mg17Al12 phase, which strengthens the weld. The subsequent decrease is due to the grain growth in the heat affected zone, which weakens the joint.
  4. Fracture Location: The tensile fracture occurs mainly in the heat affected zone, and the fracture mode is quasi-cleavage fracture. This is because the heat affected zone has the lowest hardness and the largest grain size, making it the weakest part of the joint.

For the shop floor, the practical significance of this paper is clear. The welding heat input must be carefully controlled to achieve the desired microstructure and mechanical properties. Too low a heat input results in insufficient β-Mg17Al12 phase and low strength. Too high a heat input results in excessive grain growth and low strength. The optimal heat input is the one that balances these two effects.

Integration with Manufacturing Practice and Lessons Learned

I have seen many examples of the effect of heat input on the microstructure and mechanical properties of welded joints. In one project, we were welding AZ31 magnesium alloy sheets for an aerospace application. The sheets were 2 mm thick, and we were using AC TIG welding. The first few welds we made had low tensile strength, and the fracture occurred in the heat affected zone.

We then decided to investigate the effect of the welding heat input on the microstructure and mechanical properties. We conducted a series of welding trials with different welding currents, ranging from 70 A to 110 A. We measured the tensile strength and the elongation of the welded joints and examined the microstructure.

The results were consistent with the paper's findings. At 70 A, the tensile strength was low, and the fracture occurred in the heat affected zone. At 90 A, the tensile strength was the highest, and the fracture occurred in the heat affected zone. At 110 A, the tensile strength was lower, and the fracture occurred in the heat affected zone.

Based on these results, we selected a welding current of 90 A for the production welds. The result was a significant improvement in the tensile strength and a reduction in the number of defects.

The paper's emphasis on the effect of the heat input on the microstructure is well-founded. In our experience, the heat input is the most important factor in controlling the microstructure and mechanical properties of magnesium alloy welds.

Critical Evaluation and Engineering Judgement

The paper is a good example of the application of metallurgical analysis to a practical problem. However, it has some limitations that are worth noting. First, the paper does not provide a detailed analysis of the welding parameters, such as the voltage, travel speed, and shielding gas flow rate. This makes it difficult to reproduce the results. Second, the paper does not address the effect of the welding process on the corrosion resistance of the weld. In magnesium alloys, the corrosion resistance is an important consideration, and the welding process can affect it.

Third, the paper does not address the effect of the welding process on the residual stress and distortion. In thin-wall components, the residual stress and distortion are often the limiting factors. The paper would be more useful if it provided a complete analysis of the welding process.

Despite these limitations, the paper is a valuable contribution to the field. It provides a good example of how to approach the problem of optimizing the welding heat input for magnesium alloys.

Study Insights and Recommendations for Further Work

This paper has reinforced my belief that the welding heat input is the most important factor in controlling the microstructure and mechanical properties of welded joints. The paper provides a good example of how to optimize the heat input for magnesium alloys.

For further work, I would like to see studies that provide a complete analysis of the welding process, including the residual stress and distortion. I would also like to see studies that address the effect of the welding process on the corrosion resistance of the weld. The paper provides a solid foundation for these extensions, and I would recommend it to any engineer who is involved in the welding of magnesium alloys.

In my experience, the most important lesson from this type of research is that the welding process must be optimized for the specific material and application. The paper is a step in that direction, and I look forward to seeing how this field evolves in the coming years.