ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

AC TIG Welding Process Optimization for L2 Pure Aluminum

Literature Overview and Core Findings

The study by Pang Liang from Inner Mongolia Second Electric Power Construction Engineering Co., Ltd. investigates the AC TIG welding of L2 pure aluminum. The paper first analyses common faults in tungsten inert gas welding, their causes, and preventive measures. It then presents the results of welding trials using an automatic pulsed AC TIG process. For 3mm thick L2 aluminum plate, the optimal parameters were determined: base current 90A, pulse current 170A, welding speed 178mm/min, wire feed speed 0.9m/min, and pulse frequency 2Hz. Under these conditions, the joint tensile strength reached 86.0942MPa, which is close to the base metal strength. The weld showed minimal porosity and inclusions, and the HAZ grain size was finer and more uniform than with other parameter combinations.

This is a practical paper that addresses a real production problem: how to weld pure aluminum reliably and consistently. Pure aluminum is soft, has a high thermal conductivity, and forms a tenacious oxide film. AC TIG is the standard process because the alternating current provides a cleaning action that breaks up the oxide film during the reverse polarity half-cycle.

Technical Interpretation and Process Analysis

The key to welding aluminum is managing the oxide film. During the electrode positive (EP) half-cycle of the AC current, the workpiece is the anode, and the arc bombards the surface, breaking up the oxide film. During the electrode negative (EN) half-cycle, the workpiece is the cathode, and the arc provides the heat for melting. The balance between EP and EN determines the cleaning action and the penetration.

The pulsed AC process adds another dimension. By pulsing the current between a base value and a peak value, the heat input can be controlled more precisely. The base current maintains the arc and provides a minimum level of heat, while the peak current provides the energy for melting and penetration. The pulse frequency determines the number of pulses per second, which affects the weld bead appearance and the grain structure.

The optimal parameters reported in this paper are a good starting point for 3mm thick L2 aluminum:

Parameter Value Effect
Base current 90A Maintains arc, provides minimum heat
Pulse current 170A Provides melting and penetration
Welding speed 178mm/min Controls heat input per unit length
Wire feed speed 0.9m/min Matches the melting rate
Pulse frequency 2Hz Controls bead appearance and grain size

The resulting tensile strength of 86.0942MPa is close to the base metal, which indicates a high-quality joint. The low porosity and inclusion content are also positive indicators.

Engineering Practice and Lessons Learned

In my experience, the most common problem with aluminum TIG welding is porosity. The oxide film on the aluminum surface contains moisture, which dissociates in the arc and releases hydrogen. The hydrogen dissolves in the molten aluminum and is trapped during solidification, forming pores. The AC cleaning action helps remove the oxide, but it does not eliminate the moisture. The filler wire must be clean and dry, and the shielding gas must be of high purity.

Another common problem is lack of fusion, which occurs when the heat input is too low. The high thermal conductivity of aluminum means that heat is conducted away quickly, and the weld pool may not penetrate fully. The pulsed AC process helps by providing a high peak current that ensures penetration, while the base current allows the weld pool to solidify slightly between pulses, which can improve the bead shape.

One lesson I have learned: the welding speed is critical. If you weld too slowly, the heat input is excessive, and the HAZ becomes coarse and weak. If you weld too fast, you get lack of fusion and porosity. The optimal speed must be determined by trial and error, and it depends on the thickness, the joint geometry, and the filler wire.

Key Reflections and Recommendations

This paper provides a solid practical foundation for AC TIG welding of pure aluminum. The optimal parameters are a good starting point, but they should be verified for your specific application. The joint strength is excellent, and the weld quality is high. The key to success is controlling the heat input, maintaining a clean surface, and using high-quality filler wire and shielding gas.

For fellow engineers, I would emphasise that aluminum welding is not forgiving. The process window is narrow, and small changes in parameters can have a big effect on quality. The pulsed AC process is a powerful tool, but it must be used with care. This paper gives you a reference point, and the practical experience of the author is evident in the thorough analysis of common faults and their prevention.

My final recommendation is to always qualify the welding procedure for aluminum with mechanical testing. Do not rely on visual inspection alone. The strength and porosity of the joint are the critical parameters, and they can only be verified by testing. This paper provides a good example of the testing that should be done, and the results are a benchmark for what can be achieved with the right parameters and good practice.