ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Temperature Field Simulation of Invar Alloy TIG Welding

Core Content and Significance

This paper addresses a classic challenge in welding engineering: predicting the temperature field and penetration behavior when welding Invar alloy, a material with a very low coefficient of thermal expansion. The authors used the ANSYS finite element software with a double ellipsoid heat source model to simulate the temperature distribution during TIG welding of Invar alloy to 45 steel. They then validated their simulation against actual welding trials, measuring deformation at specific locations during the process.

The significance of this work lies in the combination of numerical simulation with experimental verification. Too often, engineers run simulations that look impressive on screen but have no connection to what actually happens on the welding table. Here, the authors made a deliberate effort to confirm that their model predicted the correct penetration behavior, which is the critical parameter for any welding application.

Technical Points and Simulation Approach

The double ellipsoid heat source model, originally developed by Goldak, is the standard approach for simulating arc welding processes. The authors applied it correctly, accounting for the difference between the front and rear heat distribution of the moving arc. The key parameters and results are summarized below.

Parameter Value Notes
Welding current 132 A Selected to achieve full penetration
Arc voltage 17.1 V Typical for TIG welding
Welding speed 4 mm/s Equivalent to 240 mm/min
Plate thickness 1.88 mm Thin section, challenging for full penetration
Heat source model Double ellipsoid Goldak model
Simulation software ANSYS Coupled temperature-displacement analysis

The simulation was performed as a weak coupling between the temperature field and the stress field. This means they first calculated the temperature distribution and then used that as input for the mechanical analysis. This is a reasonable approach for welding, where the thermal effects dominate and the mechanical response is largely a consequence of the thermal history.

The critical finding is that at the specified parameters, full penetration welding of the 1.88 mm thick Invar alloy was achieved, and the simulation results matched the experimental observations. This is the kind of validation that gives confidence in the model for future applications.

Practical Implications for Manufacturing

Invar alloy is used in applications where dimensional stability is critical, such as LNG storage tanks, precision instruments, and components in the aerospace and electronics industries. The low coefficient of thermal expansion, around 1.2 to 2.0 × 10⁻⁶ /°C, means that welding-induced distortion is much less of a problem than with conventional steels. However, this same property creates challenges: the material tends to have poor weldability due to the formation of brittle phases, and controlling the heat input is essential to avoid cracking.

For a pipe or fitting manufacturer, the relevance of this work is in understanding how to achieve full penetration on thin sections without burning through or creating excessive distortion. The validated simulation model allows engineers to explore different parameter combinations without conducting expensive and time-consuming physical trials. This is particularly valuable when developing procedures for new thicknesses or joint configurations.

The fact that the authors achieved full penetration at 132 A on a 1.88 mm plate is a useful reference point. In my experience, thin-section TIG welding is all about balancing heat input against the risk of burn-through. The simulation provides a way to visualize the temperature distribution and identify the safe operating window before ever striking an arc.

Lessons and Reflections

One of the most important lessons from this paper is the value of validating simulation against experiment. I have seen many simulation studies in the literature that present beautiful temperature field plots but never verify them against actual welding. The authors here did it right: they ran the simulation, then they ran the actual welding trials, and they compared the results. This is the discipline that separates useful engineering research from academic exercises.

Another lesson concerns the choice of heat source model. The double ellipsoid model is more complex than a simple Gaussian or point source, but it provides a more realistic representation of the heat distribution from a moving arc. For thin-section welding, where the thermal gradients are steep and the penetration behavior is sensitive to small changes in heat input, the additional complexity is justified.

From a practical standpoint, the specific parameters reported here are a starting point, not a final answer. The 132 A current and 4 mm/s speed worked for this particular plate thickness and joint configuration. For a different thickness or a different alloy composition, the parameters would need to be adjusted. The value of the simulation is that it allows you to make those adjustments intelligently rather than by trial and error.

Conclusion

This paper demonstrates a rigorous approach to simulating the TIG welding temperature field for Invar alloy, with the critical step of experimental validation. The double ellipsoid heat source model, combined with a weak coupling between thermal and mechanical analysis, provided accurate predictions of penetration behavior. For engineers working with low-expansion alloys or thin-section components, the methodology described here offers a practical way to develop welding procedures with confidence. The key lesson is that simulation is a tool to support engineering judgment, not a replacement for it. The model must always be validated against reality before it is used to make production decisions.