ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Effect of Environmental Humidity on AM60 Magnesium Alloy TIG Welding Process and Joint Microstructure and Properties

Introduction and Literature Context

The 2008 study by Lu Sheng and colleagues from Jiangsu University of Science and Technology addresses a practical issue that every welding shop faces: the effect of ambient humidity on weld quality. The study focuses on AM60 magnesium alloy, which is used in automotive and aerospace applications where weight reduction is critical. The authors systematically investigated the effect of relative humidity (60% vs. 85%) on TIG welding of AM60, examining porosity, joint microstructure, and mechanical properties. This is a valuable study because it provides quantitative data on how humidity affects welding and offers practical guidance for process parameter selection.

Experimental Approach

Material and Welding Conditions

AM60 is a cast magnesium alloy with approximately 6% aluminum and 0.2% manganese. The aluminum provides solid solution strengthening and precipitation hardening, while manganese improves corrosion resistance. The welding was performed using TIG with argon shielding gas. The key variables were welding current (ranging from low to 170 A) and argon flow rate (ranging from 4 to 10 L/min). The tests were conducted at two humidity levels: 60% RH (dry condition) and 85% RH (humid condition).

Humidity as a Process Variable

The relative humidity directly affects the amount of water vapor in the welding environment. Water vapor dissociates in the arc to produce hydrogen, which is highly soluble in molten magnesium. When the weld metal solidifies, the hydrogen solubility decreases dramatically, causing hydrogen to precipitate as gas bubbles. This is the primary cause of porosity in magnesium welds. The higher the humidity, the more hydrogen is available, and the more severe the porosity.

Porosity Formation and Control

Mechanism of Hydrogen Porosity

The mechanism is well understood:

  1. Water vapor in the atmosphere is drawn into the arc region.
  2. The arc energy dissociates water vapor into hydrogen and oxygen.
  3. Hydrogen dissolves into the molten weld pool.
  4. During solidification, the solubility of hydrogen in solid magnesium is much lower than in liquid magnesium.
  5. The excess hydrogen precipitates as gas bubbles, which are trapped in the solidifying weld metal as porosity.

Effect of Welding Parameters on Porosity

The study found that in humid conditions, porosity is a significant problem unless the welding parameters are carefully selected. Two parameters are particularly important:

  1. Welding Current: Higher current (170 A) provides more heat input, which increases the weld pool size and allows more time for hydrogen to escape before solidification. The larger pool also dilutes the hydrogen concentration, reducing the driving force for bubble formation.
  2. Argon Flow Rate: Higher argon flow (8-10 L/min) provides better shielding, reducing the amount of water vapor that reaches the arc region. The higher flow rate also creates a more effective gas curtain that excludes atmospheric moisture.

Parameter Selection Strategy

The study provides a clear strategy for welding in humid conditions:

Condition Recommended Current Recommended Argon Flow Porosity Risk
Dry (60% RH) Wide range acceptable 4-10 L/min Low
Humid (85% RH) 170 A 8-10 L/min Controlled
Humid (85% RH) Lower current Lower flow High

Microstructural Effects

Grain Size and HAZ

In dry conditions, the welding parameters can be optimized to use lower heat input, which results in finer grain size in both the weld metal and the heat-affected zone. Finer grains provide better mechanical properties according to the Hall-Petch relationship. The HAZ grain growth is also minimized with lower heat input, reducing the softening effect.

Porosity and Joint Quality

The presence of porosity significantly degrades joint quality. Pores act as stress concentrators and reduce the effective load-bearing area. In fatigue applications, porosity is particularly detrimental because pores can initiate fatigue cracks. The study confirms that eliminating porosity is essential for achieving acceptable mechanical properties.

Mechanical Property Comparison

Condition Welding Current Argon Flow Tensile Strength Elongation Porosity
Dry (60% RH) Optimized Optimized High Good None
Humid (85% RH) 170 A 8-10 L/min Improved Improved Reduced
Humid (85% RH) Low Low Low Poor Significant

The results show that in humid conditions, using the recommended parameters (170 A, 8-10 L/min) can achieve mechanical properties close to those obtained in dry conditions. This is a practical and important finding because it means welding can continue in humid environments with appropriate parameter adjustment.

Practical Shop Floor Implications

Environmental Control in the Welding Shop

The study's findings have direct implications for welding shop management:

  1. Monitor Humidity: Every welding shop should have a hygrometer and record humidity levels. Welding should be scheduled during low-humidity periods when possible.
  2. Parameter Adjustment: When welding in humid conditions, increase welding current and argon flow to compensate for the increased hydrogen pickup. The study provides specific guidance: use 170 A and 8-10 L/min for AM60.
  3. Pre-Weld Cleaning: The base material must be clean and dry before welding. Any moisture on the surface will contribute to hydrogen pickup. The study does not explicitly address this, but it is a well-known practice.
  4. Shielding Gas Quality: The argon used for shielding must be dry. Moisture in the shielding gas is a direct source of hydrogen. Regular checks of gas purity and dew point are essential.

Quality Control

Check Method Acceptance Criteria
Porosity Radiographic testing No visible porosity in critical areas
Joint strength Tensile test ≥ 80% of base metal
Microstructure Metallographic exam Fine grain, no excessive HAZ growth
Surface quality Visual inspection No cracks, no surface contamination

Lessons Learned and Recommendations

This study provides practical guidance for a common problem in magnesium alloy welding. The key takeaways are:

  1. Humidity is a critical process variable that must be monitored and controlled.
  2. Higher welding current and argon flow can compensate for the effects of humidity.
  3. Dry conditions allow a wider process window and better mechanical properties.
  4. Porosity is the primary defect in humid conditions and must be controlled to achieve acceptable joint quality.

For engineers and shop managers, the following recommendations are essential:

  1. Implement a humidity monitoring program in the welding shop.
  2. Develop a parameter adjustment protocol for humid conditions.
  3. Train welders to recognize the signs of porosity and adjust parameters accordingly.
  4. Verify joint quality with NDT, particularly when welding in humid conditions.

In summary, this study provides a clear and practical framework for welding AM60 magnesium alloy in varying humidity conditions. The findings are directly applicable to production environments and demonstrate that with proper parameter selection, acceptable joint quality can be achieved even in humid conditions. The lessons learned extend beyond magnesium to any material that is susceptible to hydrogen porosity, including aluminum and titanium alloys.