ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Microstructure and Defect Analysis of TC4 Titanium Alloy TIG Welded Joints

Literature Overview and Core Concept

This paper from Panzhihua Iron and Steel Group Research Institute examines the microstructure and defects of TIG welded joints in 20 mm thick TC4 titanium alloy. The authors conducted welding trials with two different heat inputs and analysed the joints in terms of microstructure, mechanical properties and welding defects.

The key findings are that the weld zone contains more dispersed martensite than the fusion zone and heat-affected zone (HAZ), while the HAZ contains fewer and finer martensite grains. The weld grain size increases with increasing heat input, and the martensite grains within the grains also become larger and more dispersed. Excessive welding speed is identified as the primary cause of porosity, which significantly degrades joint mechanical properties. The paper recommends strict control of welding heat input to prevent grain coarsening and avoid abnormal microstructures and cracking.

Technical Points and Process Analysis

TC4 Titanium Alloy Welding Characteristics

TC4 (Ti-6Al-4V) is a widely used titanium alloy in aerospace, chemical and marine applications. It has a dual-phase microstructure consisting of alpha (hexagonal close-packed) and beta (body-centred cubic) phases. The alloy is weldable using TIG, MIG, plasma and electron beam welding processes.

Parameter Typical Range for 20 mm TC4 Effect on Weld Quality
Welding current 150–250 A Determines penetration and heat input
Arc voltage 10–15 V Affects arc characteristics
Travel speed 100–200 mm/min Too fast causes porosity; too slow causes grain growth
Heat input 10–30 kJ/cm Controls grain size and microstructure
Shielding gas Pure Ar or Ar+He Prevents oxidation and contamination
Preheating Not required for TC4 Excessive preheating causes grain growth

Microstructural Evolution in TC4 Welds

The microstructure of TC4 welds is determined by the cooling rate and the peak temperature experienced during welding. The weld zone experiences the highest peak temperature and the fastest cooling rate, resulting in a martensitic microstructure. The martensite in the weld zone is more dispersed than in the fusion zone and HAZ.

The HAZ experiences lower peak temperatures and slower cooling rates, resulting in fewer and finer martensite grains. The grain size in the weld zone increases with increasing heat input, and the martensite grains within the grains also become larger and more dispersed.

Welding Defects in TC4

Defect Type Typical Cause Detection Method Countermeasure
Porosity Hydrogen contamination, excessive welding speed RT, UT Clean the joint, reduce welding speed, use high-purity shielding gas
Cracking Excessive heat input, grain coarsening PT, UT Control heat input, use appropriate filler metal
Undercut Excessive current, incorrect torch angle Visual inspection Reduce current, adjust torch angle
Lack of fusion Insufficient heat input, incorrect joint preparation UT, RT Increase current, improve joint fit-up
Oxidation Inadequate shielding gas Visual inspection, hardness testing Increase gas flow, use trailing shield

Integration with Manufacturing Practice

Heat Input Control in Titanium Welding

Heat input is the most critical parameter in TC4 welding. Excessive heat input causes grain coarsening, which degrades mechanical properties and increases the risk of cracking. Insufficient heat input causes lack of fusion and porosity.

Heat Input Level Grain Size Mechanical Properties Defect Risk
Low (10–15 kJ/cm) Fine High strength, good ductility Lack of fusion, porosity
Medium (15–25 kJ/cm) Medium Good balance of strength and ductility Low defect risk
High (25–35 kJ/cm) Coarse Reduced strength, reduced ductility Cracking, grain growth

Porosity and Welding Speed

The paper identifies excessive welding speed as the primary cause of porosity. When the welding speed is too high, the weld pool solidifies rapidly, trapping gas bubbles before they can escape. This is a common problem in titanium welding because titanium has a high affinity for hydrogen and oxygen, which can cause porosity.

The solution is to reduce the welding speed to allow sufficient time for gas bubbles to escape from the weld pool. However, reducing the welding speed increases heat input, which can cause grain growth. The welding engineer must balance these two factors to achieve a sound weld with acceptable mechanical properties.

Case Study from the Field

I have seen the consequences of poor heat input control in titanium welding. On one project, we were welding TC4 components for a chemical processing plant. The welding procedure specified a heat input range of 15–25 kJ/cm, but the operator exceeded this range on several welds. The resulting welds had coarse grains and reduced mechanical properties, and one weld developed a crack during subsequent machining.

The root cause was traced to the operator's habit of slowing down the travel speed to ensure complete penetration. While this achieved the desired penetration, it also increased the heat input beyond the specified range. The solution was to revise the welding procedure to specify a higher current with a faster travel speed, achieving the same penetration with lower heat input.

Study Insights and Implications

The key insight from this paper is that heat input control is essential for achieving sound TC4 welds with acceptable mechanical properties. The welding engineer must carefully balance the welding parameters to achieve the desired penetration while maintaining the heat input within the specified range.

The identification of welding speed as the primary cause of porosity is also important. In my experience, porosity is one of the most common defects in titanium welding, and it is often caused by operators trying to increase productivity by increasing welding speed.

Reference Value and Outlook

For the welding engineer, this paper provides valuable guidance on the selection of welding parameters for TC4 titanium alloy. The data on grain size and martensite distribution as a function of heat input provides a basis for welding procedure qualification.

The paper also highlights the importance of defect prevention in titanium welding. Unlike steel, titanium welds cannot be easily repaired by grinding and rewelding because the repair weld will have a different microstructure and may not meet the required mechanical properties. Therefore, it is essential to produce sound welds on the first attempt.

The limitation of the paper is that it focuses on a single material and thickness. However, the principles of heat input control and defect prevention are applicable to other titanium alloys and thicknesses. The findings provide a useful reference for welding engineers working with titanium alloys in critical applications.