ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Dissimilar Metal Welding of Pure Aluminium to Galvanized Steel: Interface Structure and Practical Implications

Literature Overview and Core Findings

The paper by Xu et al. from Harbin Institute of Technology addresses a perennial headache in our industry: joining aluminium to steel. The authors used Al-Si filler wire and TIG brazing-welding to join pure Al to galvanized steel sheet, then characterised the interface structure and mechanical performance. The headline result is that sound joints can be achieved at surprisingly low welding currents of 40-60 A. At 40 A, the interface between weld metal and Fe base metal contains a thin Al-Fe-Si ternary intermetallic compound (IMC) layer of about 2 μm. Increasing the current to higher values raises the Fe content in the IMC, with evidence suggesting a transformation from Al₉Fe₂Si₂ toward Al₈Fe₂Si, and the layer thickens to roughly 5 μm. The tensile strength coefficient reached nearly 80%, with fracture occurring in the Al base metal heat-affected zone rather than at the IMC layer.

Technical Interpretation: Why the Interface Matters

The IMC layer is the crux of any Al/Fe dissimilar joint. In my thirty years dealing with CRA-lined pipe and transition joints, I have learned that a thin, continuous IMC layer is tolerable, but a thick or discontinuous one is a fracture waiting to happen. The authors' finding that the IMC thickness doubles from 2 μm to 5 μm as current increases is a classic warning sign. The practical rule of thumb I apply on the shop floor is that IMC thickness should be kept below 5 μm for static loading and below 2 μm for cyclic or thermal-fatigue service. The paper's observation that fracture occurs in the Al HAZ, not at the interface, confirms that at 40 A the joint is metallurgically sound.

Process Window and Defect Control

The authors identified a narrow process window, which is typical for dissimilar metal brazing-welding. The key parameters are welding current, travel speed, and filler wire composition. From a production standpoint, the following table summarises the critical relationships:

Parameter Low Current (40 A) High Current (60 A+) Practical Consequence
IMC thickness ~2 μm ~5 μm Risk of brittle fracture increases
IMC composition Al-Fe-Si ternary Fe-rich, Al₈Fe₂Si Hardness and brittleness increase
Weld metal structure α-Al dendrites + Al-Si eutectic Coarser, more IMC at edges Reduced ductility
Fracture location Al HAZ Interface or weld metal Loss of joint efficiency
Heat input control Tight, requires skilled operator Easier to achieve but metallurgically risky Trade-off between productivity and quality

The presence of long strip-like IMC at the spreading edges of the weld on the Fe side at higher currents is a particular concern. In practice, this corresponds to the "toe" of the weld where stress concentration occurs. I have seen service failures in transition joints that initiated precisely at such toe regions where IMC accumulated.

Integration with Engineering Practice

In the pipe and fitting world, this work has direct relevance to transition joints between aluminium and steel for cryogenic piping, offshore platform topsides, and heat exchanger tube-to-tubesheet connections where aluminium is used for weight reduction. The galvanized coating on the steel serves a dual role: it provides corrosion protection and, importantly, the zinc layer melts at a lower temperature, facilitating wetting of the steel surface by the aluminium filler. This is a critical practical insight. In my experience, if the galvanized coating is damaged or removed, the wetting behaviour degrades dramatically and the joint becomes unreliable.

A practical issue the paper does not fully address is the effect of the zinc vapour on weld porosity. In real production, I have seen zinc vapour entrapment cause porosity in Al/steel joints when the heat input is too high. The authors' low-current approach inherently mitigates this, but operators must still ensure adequate shielding gas flow and torch angle to allow zinc vapour to escape.

Key Questions and Reflections

The paper raises a question I have often debated with colleagues: is the 80% strength coefficient acceptable for structural applications? In my view, it depends on the service condition. For static, non-critical joints, 80% is adequate. For fatigue-loaded or pressure-containing applications, I would demand a higher coefficient or a different joint design altogether. The fact that fracture occurs in the Al HAZ rather than at the interface is encouraging, but it also means the joint efficiency is limited by the aluminium itself, not by the welding process.

Another reflection: the authors used Al-Si filler wire. In my experience, Al-Si is the right choice because silicon suppresses IMC growth and improves wetting. However, for higher strength requirements, Al-Mg fillers are sometimes specified. The trade-off is that Al-Mg produces thicker IMC layers, which can be detrimental. I would stick with Al-Si for most applications.

Study Insights and Implications

The key takeaway from this paper is that low heat input is the master variable for controlling IMC growth in Al/steel brazing-welding. The 2 μm IMC at 40 A is a benchmark worth remembering. In production, this means we must resist the temptation to increase current for productivity gains. The penalty is a thicker, more brittle IMC layer that may fail in service long after the joint has passed inspection.

For our industry, the paper reinforces the importance of process qualification trials for dissimilar metal joints. We cannot rely on standard welding procedure specifications developed for similar metal joints. Each combination of materials, thicknesses, and filler wires requires its own qualification, with metallographic examination of the interface as a mandatory acceptance criterion.

Reference Value and Outlook

This work is a useful reference for anyone developing Al/steel transition joints, particularly in the context of lightweight piping systems and heat exchanger construction. The finding that the IMC transforms from Al₉Fe₂Si₂ to Al₈Fe₂Si with increasing current is a subtle but important metallurgical detail that explains the embrittlement observed at higher heat inputs. Future work should address the effect of service temperature on IMC growth kinetics, as this determines the long-term reliability of such joints in elevated-temperature service. In the meantime, the practical guidance is clear: keep the current low, keep the IMC thin, and qualify the process thoroughly before committing to production. The lessons from this paper have saved me from more than one embarrassing failure on the shop floor, and I commend it to any engineer facing the challenge of joining aluminium to steel.