ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

IGBT Dual-Inverter Square-Wave AC TIG Welding Machine - Technical Analysis

Machine Design and Topology

This study by Liu Guiqiu, Hang Zhengxiang and Wang Hui from Shenyang University of Technology and Liaoyang Petrochemical College examines the design of an IGBT dual-inverter square-wave AC TIG welding machine. Published in Power Electronics Technology in 1997, this work addresses the challenge of welding aluminum and its alloys, which require AC TIG welding with a square-wave output for stable arc and good oxide removal.

The dual-inverter topology is the key innovation. The machine uses two inverter stages: a primary inverter that converts the mains input to a high-frequency AC, and a secondary inverter that converts the intermediate DC bus to the square-wave AC output. This topology provides several advantages:

Feature Benefit
Primary inverter Provides isolation and voltage step-down
Secondary inverter Generates square-wave AC output
IGBT switching High frequency, low losses
Square-wave output Stable arc, good oxide removal

The square-wave output is critical for aluminum welding. A sinusoidal AC output has a slow current reversal that can cause arc instability and oxide inclusions. A square-wave output provides rapid current reversal, which improves arc stability and oxide removal.

Control Strategy and Performance

The control strategy uses primary inverter current negative feedback and threshold comprehensive control to achieve constant current characteristics. This means the welding current is maintained at a constant value regardless of arc length variations, which is essential for consistent weld quality.

The secondary inverter uses a specific arc initiation control method. For AC TIG welding, the arc must be initiated on each half-cycle. The proposed method controls the secondary inverter to provide a high-frequency, high-voltage pulse for arc initiation, then switches to the welding current.

The experimental results are presented below:

Parameter Value Notes
Open-circuit voltage 45 V Sufficient for arc initiation
Minimum stable current 15 A Stable arc at low current
Welding material Aluminum alloy Stable welding achieved
Output waveform Square wave Improved arc stability

The key achievement is stable welding of aluminum alloy at currents as low as 15 A. This is significant because low-current welding of thin aluminum sections is challenging due to the oxide layer and the high thermal conductivity of aluminum.

Aluminum Welding Application

The practical application is aluminum pipe and fitting welding. Aluminum pipe is used in HVAC systems, process piping and structural applications. The main challenges in aluminum welding are:

  1. Oxide removal. The aluminum oxide layer has a melting point of 2072°C, much higher than the aluminum melting point of 660°C. The oxide must be removed by the arc, which requires the reverse polarity half-cycle.
  2. Arc stability. The arc must be stable to produce consistent weld quality. The square-wave output provides better stability than sinusoidal output.
  3. Heat input control. Aluminum has high thermal conductivity, so heat input must be controlled carefully to avoid burn-through on thin sections.

The dual-inverter square-wave AC TIG machine addresses all three challenges. The square-wave output provides rapid current reversal for oxide removal, the constant current control maintains arc stability, and the low minimum current allows welding of thin sections.

Reliability and Maintenance Considerations

The IGBT dual-inverter topology has specific reliability considerations:

Component Failure Mode Preventive Action
IGBT modules Overheating, overcurrent Proper heatsinking, current limiting
Capacitors Electrolyte degradation Regular replacement, temperature monitoring
Control boards Component failure Redundant design, spare parts
Cooling fans Bearing failure Regular maintenance, replacement

The 1997 vintage of this design means the components are now obsolete, but the topology and control strategy remain relevant. Modern machines use more advanced IGBTs and digital control, but the fundamental principles are unchanged.

Comparison with Conventional AC TIG

The comparison between conventional AC TIG and the dual-inverter square-wave AC TIG is instructive:

Feature Conventional AC TIG Dual-Inverter Square-Wave AC TIG
Output waveform Sinusoidal Square wave
Arc stability Moderate Excellent
Oxide removal Moderate Excellent
Minimum current Higher Lower
Efficiency Lower Higher
Control Analog Digital

The square-wave output is the key differentiator. The rapid current reversal provides better arc stability and oxide removal, which is essential for aluminum welding.

Summary

This study presents a well-designed dual-inverter square-wave AC TIG welding machine that addresses the specific challenges of aluminum welding. The IGBT topology provides high efficiency and compact size, while the square-wave output provides stable arc and effective oxide removal. The constant current control and arc initiation method ensure reliable operation at low currents. For aluminum pipe welding, this machine offers significant advantages over conventional AC TIG machines, particularly for thin sections and critical applications. The practical lesson is that the welding machine design directly affects weld quality, and the choice of machine should be based on the specific welding application. The dual-inverter square-wave topology remains a sound design principle for modern machines, even though the specific components have evolved.