ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Hot-Wire TIG Welding in Converter Vaporization Cooling Flue Manufacturing: Process Advantages and Practical Application

Introduction and Why This Topic Matters

The converter vaporization cooling flue is one of the most demanding components in a steel plant. It operates at high temperature, sees thermal cycling, and carries water under pressure, and the welds between the small-diameter, medium-thick-wall tubes are the most critical part of the assembly. Tang Jianfeng's paper from Maanshan Iron and Steel Company addresses a problem I know well: how do you weld a small-diameter tube, with a wall thickness of maybe 8 to 14 mm, in a fixed position, and get a weld that is sound, consistent, and economical? Conventional TIG welding is slow, and the heat input is difficult to control, especially in the overhead position. Hot-wire TIG welding, where the filler wire is preheated by resistance before it enters the weld pool, offers a solution that I have seen work well in similar applications, and this paper provides a solid technical justification for its use.

The paper covers the basic principles of hot-wire TIG, the characteristics of the process, the process parameters, and the practical application in the manufacture of converter vaporization cooling flues. The author's conclusion that hot-wire TIG is a mature, efficient, and high-quality process for small-diameter, medium-thick-wall tube butt welding in fixed position is one I agree with, but I would add some caveats based on my own experience.

Process Principles and Characteristics of Hot-Wire TIG

In conventional TIG welding, the filler wire is cold when it enters the arc, and the arc energy is used both to melt the wire and to melt the base metal. In hot-wire TIG, the filler wire is resistance-heated as it passes through a contact tip, so it enters the weld pool at a temperature close to its melting point. This has several important effects. First, the deposition rate increases significantly because the wire does not need to absorb as much heat from the arc. Second, the heat input to the base metal can be reduced for a given deposition rate, which means less distortion and a narrower heat-affected zone. Third, the weld pool is more stable because the wire melts more uniformly, reducing the risk of lack of fusion and porosity.

Let me put the typical process parameters in a table, based on what the paper reports and what I have seen in practice.

Parameter Conventional TIG Hot-Wire TIG Practical Notes
Welding current (A) 150-250 120-200 Lower current for same deposition
Arc voltage (V) 10-14 10-14 Similar
Wire diameter (mm) 1.6-2.4 1.2-2.0 Smaller wire preferred
Wire feed speed (m/min) 0.5-1.0 1.5-3.0 Much higher deposition rate
Wire preheat current (A) N/A 30-80 Depends on wire diameter
Deposition rate (kg/h) 0.5-1.0 2.0-4.0 Two to four times higher
Heat input (kJ/mm) 1.0-2.0 0.8-1.5 Lower for same deposition

The key advantage is that the wire preheat current is independent of the arc current, so you can control the deposition rate and the heat input separately. This is a significant improvement over conventional TIG, where the two are coupled. In practice, this means you can weld a thin-walled tube with a high deposition rate without burning through, or you can weld a thick-walled tube with a low heat input without excessive distortion. For the converter flue, where the tubes are small in diameter but have a medium wall thickness, this is exactly what you need.

Process Parameters and Practical Application

The paper discusses the application of hot-wire TIG to the converter vaporization cooling flue, which is a complex assembly of tubes that are welded in fixed position. The tubes are typically 25 to 60 mm in diameter with wall thicknesses of 6 to 14 mm, and they are welded in a variety of positions, including horizontal, vertical, and overhead. The author reports that hot-wire TIG was able to achieve a deposition rate of 2 to 3 kg/h, which is two to three times higher than conventional TIG, while maintaining a weld quality that met the requirements for pressure vessels.

In my own experience, the critical parameters for hot-wire TIG are the wire preheat current, the wire feed speed, and the arc length. The wire preheat current must be set so that the wire is heated to a temperature that is high enough to ensure smooth melting but not so high that the wire melts before it reaches the weld pool, which would cause spatter and instability. The wire feed speed must be matched to the welding current to maintain a stable arc and a consistent weld bead. The arc length must be kept short, typically 2 to 3 mm, to ensure good shielding and to prevent the wire from touching the tungsten electrode.

Let me put together a typical process window for hot-wire TIG on medium-thick-wall tubes, based on the paper and my own experience.

Parameter Typical Range Critical Limit Effect of Exceeding Limit
Wire preheat current (A) 40-70 80 Wire melts before pool, spatter
Wire feed speed (m/min) 1.5-2.5 3.0 Arc instability, lack of fusion
Arc length (mm) 2-3 4 Poor shielding, porosity
Welding current (A) 130-180 200 Excessive heat input, distortion
Shielding gas flow (L/min) 10-15 8 Air entrainment, oxidation
Travel speed (mm/min) 80-120 150 Lack of fusion at high speed

The author emphasizes that hot-wire TIG is particularly suitable for fixed-position welding because the wire preheat reduces the heat input to the base metal, which minimizes the risk of burn-through in the overhead position. This is a significant advantage, because overhead welding is the most difficult position for any welding process, and the risk of lack of fusion is highest there. In my experience, the key to successful overhead welding with hot-wire TIG is to keep the wire feed speed low enough to maintain a small, stable weld pool, and to use a slight weaving motion to ensure good sidewall fusion.

Quality Assurance and Common Defects

The paper does not go into great detail on defects, but I can add some practical observations based on my experience with hot-wire TIG on small-diameter tubes. The most common defects are lack of sidewall fusion, porosity, and tungsten inclusions. Lack of sidewall fusion is usually caused by insufficient wire feed speed or excessive travel speed, which results in the weld pool not wetting the sidewall properly. Porosity is usually caused by poor shielding gas coverage, which can be a result of an excessively long arc length or a low gas flow rate. Tungsten inclusions are caused by the filler wire touching the tungsten electrode, which can happen if the wire feed speed is too high or if the arc length is too short.

Let me put these defects in a table with their causes and countermeasures, as I would on the shop floor.

Defect Primary Cause Countermeasure
Lack of sidewall fusion Wire feed speed too low Increase wire feed speed by 10-20%
Lack of sidewall fusion Travel speed too high Reduce travel speed by 10-15%
Porosity Arc length too long Reduce arc length to 2-3 mm
Porosity Gas flow too low Increase gas flow to 12-15 L/min
Tungsten inclusion Wire touches electrode Reduce wire feed speed or increase arc length
Undercut Welding current too high Reduce current by 10-15%

In my experience, the most important quality control measure for hot-wire TIG is to monitor the wire preheat current continuously. If the preheat current fluctuates, the wire temperature will fluctuate, and this will cause inconsistent melting and poor weld quality. I have seen cases where the preheat current was set correctly but the contact tip was worn, causing arcing between the wire and the tip, which resulted in erratic wire heating and porosity. The solution is to replace the contact tip regularly, typically every 50 to 100 meters of wire feed, and to check the wire feed system for any mechanical issues.

Practical Lessons and Study Insights

The paper is a good technical introduction to hot-wire TIG, but I would add a few practical lessons from my own experience. First, hot-wire TIG requires a more sophisticated power source than conventional TIG. The power source must be able to provide a stable arc current and a separate, controllable wire preheat current, and it must have a fast response to changes in arc length. If you are using an older TIG power source, you may not be able to retrofit it for hot-wire operation. Second, the wire feeding system must be precise, because the wire feed speed directly affects the deposition rate and the weld quality. A wire feeder with a closed-loop control system is essential for consistent results. Third, the shielding gas must be of high purity, because titanium and other reactive metals are sensitive to oxygen and nitrogen contamination. I would recommend using argon with a purity of at least 99.995% for hot-wire TIG.

The reference value of this paper is high for anyone who is considering hot-wire TIG for tube welding, because it provides a clear explanation of the process and a practical example of its application. The outlook is that hot-wire TIG will continue to grow in popularity for small-diameter, medium-thick-wall tube welding, particularly in the power generation and chemical processing industries, where productivity and quality are both critical. I would encourage any engineer who is considering this process to conduct a trial on their own tubes, using the parameters in this paper as a starting point, and to optimize the parameters based on their specific geometry and material.

In summary, hot-wire TIG is a proven process for converter vaporization cooling flue manufacturing, and it offers a significant productivity improvement over conventional TIG while maintaining high weld quality. The key is to control the wire preheat current, the wire feed speed, and the arc length carefully, and to monitor the process continuously to avoid defects. This paper is a valuable reference for anyone who is working with small-diameter, medium-thick-wall tubes, and it reinforces the lessons I have learned over decades of welding practice: the process parameters are the foundation of quality, and the operator's skill is the final safeguard.