ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

TIG/MAG Combined Welding for Low-Temperature Diaphragm Pump Pressure Compensation Tank

Literature Overview

The paper by Wang Huan, Zhang Yunsong and Sun Quan from the pressure vessel workshop of China Nonferrous (Shenyang) Metallurgical Machinery Co., Ltd. describes the application of a combined TIG/MAG welding process to a low-temperature diaphragm pump pressure compensation tank. The tank is a pressure vessel component operating at low temperature, which demands both high root quality and good impact toughness in the weld metal and heat-affected zone. The authors replaced conventional shielded metal arc welding (SMAW) with a hybrid process: TIG for the root pass and MAG for the fill and cap passes. The reported results show clear gains in productivity, reduced labour intensity and lower manufacturing cost, with the process fully capable of replacing SMAW.

Technical Interpretation of TIG/MAG Hybrid Welding

Why TIG for the Root Pass

For low-temperature service, the root pass is the most critical region. A TIG root pass produces a clean, uniform, fully fused joint with minimal spatter and no slag entrapment. This is essential for pressure vessels that will be subjected to hydrostatic testing and low-temperature impact testing. The TIG process also gives the welder excellent control over penetration, which is critical when the root gap varies or when the fit-up is less than perfect.

Why MAG for Fill and Cap Passes

Once the root is sealed, the fill and cap passes need to be deposited at high deposition rate. MAG welding with a suitable shielding gas (typically Ar + CO2 mixture) offers a much higher deposition rate than TIG or SMAW. The combined process therefore balances quality and productivity: TIG for the critical root, MAG for the bulk.

Process Comparison Table

Parameter SMAW TIG/MAG Combined
Root pass quality Good, but slag and spatter risk Excellent, clean, no slag
Deposition rate Low to medium High (MAG fill)
Welder fatigue High (frequent electrode changes) Lower
Electrode/filler consumption Higher (stubs, coating) Lower (continuous wire)
Post-weld cleaning Required (slag removal) Minimal
Impact toughness Acceptable Comparable or better
Productivity Baseline 30–50% improvement

Engineering Practice and Lessons Learned

In my own experience with low-temperature pressure vessels, the root pass is where most defects originate. Lack of fusion, slag inclusion and undercut are common when using SMAW on small-bore nozzles or tight access joints. The TIG/MAG combination addresses these issues directly. However, there are practical pitfalls:

  1. Shielding gas selection for MAG must be matched to the base metal. For low-temperature steels, a CO2-rich mixture can increase oxygen content in the weld metal and reduce impact toughness. An Ar + 5–20% CO2 mixture is usually preferred.
  2. The transition from TIG to MAG must be managed carefully. The TIG root should be visually inspected before the MAG fill starts. Any defect in the root will be hidden by the fill, so a root inspection is mandatory.
  3. Welder qualification must cover both processes. A welder qualified only for TIG cannot automatically run MAG, and vice versa.
  4. The heat input of the MAG fill passes must be controlled to avoid excessive grain growth in the HAZ. For low-temperature steels, a maximum interpass temperature is typically specified (e.g., 150–200°C).

Key Questions and Reflections

The paper states that the process can replace SMAW entirely. I would caution against a blanket replacement. There are situations where SMAW remains the better choice: field welding where gas supply is problematic, or repairs in confined spaces where the TIG torch is difficult to manoeuvre. The decision should be made on a case-by-case basis, considering access, gas availability, and the specific code requirements.

Another point worth reflecting on is the cost of shielding gas. TIG and MAG both require gas, and the cost of argon can be significant. In remote locations or where gas supply is unreliable, SMAW may still be the pragmatic choice. The paper does not discuss this economic aspect, which is a limitation.

Study Insights and Implications

The TIG/MAG combined process is a sound engineering solution for low-temperature pressure vessels, particularly in a workshop environment where gas supply is reliable and welders are skilled in both processes. The productivity gain is real, and the root quality improvement is tangible. For pipe and fitting manufacturers, this process is equally applicable to small-bore pipe welding where root quality is critical. I would recommend that any shop considering this change first conduct a welding procedure qualification (WPQ) with the specific base metal, filler wire and shielding gas combination, and verify that the impact toughness values meet the design requirement at the specified test temperature. The process deserves a place in the toolbox, but it is not a universal answer.