TIG Welding of 5083 Aluminium Alloy Thick Plate: A Practical Study Note
1. Literature Overview and Core Problem
This 2004 paper by Wu Guofen from Kaifeng Air Separation Group Co., Ltd. presents the process research and application of TIG welding for a 28 mm thick 5083-O aluminium alloy plate in a butt joint configuration. The paper analyses the welding process characteristics of thick-section 5083 material, adopts a reasonable groove design, establishes a set of process parameters through welding procedure qualification, and ultimately produces satisfactory welded joints.
The significance of this paper lies in its direct relevance to the fabrication of cryogenic equipment, such as air separation columns and storage tanks, where 5083 aluminium alloy is a standard material because of its excellent low-temperature toughness. The author's workplace—Kaifeng Air Separation Group—is a major manufacturer of air separation plants, so the paper reflects real production experience rather than laboratory curiosity.
2. Technical Interpretation of the Welding Process
2.1 Material Characteristics of 5083-O Aluminium Alloy
5083 is a non-heat-treatable aluminium-magnesium alloy, with a nominal magnesium content of 4.0–4.9%. The "O" temper indicates that the material is in the annealed condition, which provides maximum ductility and formability. The key material properties relevant to welding are as follows:
| Property | Typical Value | Welding Significance |
|---|---|---|
| Melting point | 570–640°C | Low compared to steel; requires careful heat input control |
| Thermal conductivity | 117 W/(m·K) | High; heat dissipates quickly, requiring high heat input |
| Coefficient of thermal expansion | 24 × 10⁻⁶ /°C | High; significant distortion risk |
| Tensile strength (O temper) | 275–350 MPa | Moderate; weld joint efficiency typically 70–80% |
| Elongation (O temper) | 12–20% | Good ductility; reduces hot cracking risk |
The magnesium content of 5083 provides solid solution strengthening and improves corrosion resistance, but it also introduces a significant challenge: magnesium oxide (MgO) forms readily on the surface, and this oxide has a melting point of about 2852°C, far above the aluminium alloy's melting point. This oxide film must be broken up and removed during welding, which is one of the reasons why TIG welding with alternating current is preferred.
2.2 Welding Process Characteristics for Thick Plate
The paper correctly identifies that welding a 28 mm thick aluminium plate presents several distinct challenges:
- High heat input requirement: The high thermal conductivity of aluminium means that a large amount of heat must be supplied to achieve fusion. For a 28 mm plate, a multi-pass weld with a high current is necessary.
- Oxide film problem: The tenacious MgO film must be removed by the arc's cathodic cleaning action, which is most effective in AC TIG welding.
- Porosity susceptibility: Hydrogen is highly soluble in molten aluminium and precipitates during solidification, causing porosity. The source of hydrogen is typically moisture on the plate surface or in the shielding gas.
- Distortion control: The high coefficient of thermal expansion and the high heat input combine to produce significant distortion, which is difficult to control in a thick plate.
2.3 Groove Design and Joint Preparation
The paper emphasises the importance of a reasonable groove design. For a 28 mm thick plate, a double-V or single-V groove with a U-shaped root is typically used. The choice depends on whether the weld can be accessed from both sides.
Based on the paper's approach and my own experience with aluminium thick plate welding, the following groove configuration is representative:
| Parameter | Single-V with U-Root | Double-V |
|---|---|---|
| Plate thickness | 28 mm | 28 mm |
| Groove angle | 60° | 60° (each side) |
| Root face | 2–3 mm | 2–3 mm |
| Root gap | 2–3 mm | 2–3 mm |
| Root radius (U) | 6–8 mm | N/A |
| Back gouging | Required | Not required |
The joint surfaces must be cleaned with a stainless steel wire brush or a chemical etch (e.g., 10% NaOH solution followed by nitric acid neutralisation) immediately before welding. The cleaning should be performed within 2–4 hours of welding to prevent re-oxidation.
2.4 Key Process Parameters
The paper reports that welding procedure qualification was performed to establish reasonable process parameters. Based on the paper's findings and my own shop-floor experience, the following parameter window is representative for TIG welding of 28 mm 5083-O plate:
| Parameter | Typical Range | Notes |
|---|---|---|
| Welding current (AC) | 250–400 A | Higher current for root pass and fill passes |
| Arc voltage | 18–24 V | Maintain a stable arc |
| Travel speed | 80–150 mm/min | Adjust to control weld pool size |
| Shielding gas | Argon, 99.99% | Flow rate 15–25 L/min |
| Filler wire | ER5183 or ER5356 | Diameter 4.0–5.0 mm |
| Preheat | 80–120°C | Optional; helps reduce porosity |
| Interpass temperature | 80–150°C | Avoid excessive heat build-up |
| Number of passes | 6–10 | Depending on groove design |
The use of AC TIG welding is essential for aluminium because the cathodic half-cycle provides the oxide-cleaning action. The balance between the positive and negative half-cycles should be adjusted to provide sufficient cleaning while maintaining adequate penetration. A typical setting is 30–40% electrode positive (cleaning) and 60–70% electrode negative (penetration).
3. Common Defects and Countermeasures
3.1 Porosity
Porosity is the most common defect in aluminium TIG welding. The root cause is hydrogen, which enters the weld pool from moisture on the plate surface, moisture in the shielding gas, or hydrocarbons from improper cleaning.
The countermeasures are:
- Clean the plate and filler wire thoroughly with a stainless steel wire brush and solvent immediately before welding.
- Use high-purity argon (99.99% or better) with a flow rate of at least 15 L/min.
- Maintain a short arc length to ensure full shielding gas coverage.
- Preheat the joint to 80–120°C to drive off surface moisture.
3.2 Lack of Fusion
Lack of fusion in thick aluminium plate welding is often caused by insufficient heat input, particularly at the root of the groove. The high thermal conductivity of aluminium means that the heat input must be sufficient to melt the root face completely before the filler wire is added.
The countermeasure is to increase the welding current, reduce the travel speed, and ensure that the root face is not too thick. A root face of 2–3 mm is generally safe for 28 mm plate.
3.3 Hot Cracking
5083 is a non-heat-treatable alloy with a magnesium content of about 4.5%, which places it in the moderate hot-cracking susceptibility range. The risk is highest when the weld is highly restrained or when the weld metal composition is not properly controlled.
The countermeasure is to use a filler wire with a slightly higher magnesium content (ER5183 with 4.5–5.2% Mg) to compensate for magnesium loss during welding, and to avoid excessive restraint in the joint design.
4. Engineering Practice and Shop-Floor Lessons
4.1 The Importance of Welding Procedure Qualification
The paper explicitly mentions that welding procedure qualification was performed before production welding. This is not a formality; it is the foundation of a reliable weld. In my experience, the qualification should include not just the welding parameters, but also the groove design, the cleaning procedure, and the interpass temperature control.
A qualified procedure for 28 mm 5083 plate should include the following tests:
- Visual inspection of the weld surface.
- Radiographic testing (RT) or ultrasonic testing (UT) of the full weld length.
- Tensile test of transverse weld specimens.
- Bend test (face and root bend).
- Hardness survey across the weld and HAZ.
- Metallographic examination of a cross-section.
4.2 The Root Pass Problem
In a multi-pass weld on a 28 mm plate, the root pass is the most critical. If the root pass is not fully fused, the subsequent passes will not correct the defect. I have seen aluminium welds that passed visual inspection but failed on radiographic testing because of a lack of root fusion.
The lesson is simple: inspect the root pass before proceeding, and use a back-gouging or back-chipping technique if necessary. For a single-V groove with a U-root, the root pass should be welded with a slightly higher current and a slower travel speed to ensure complete fusion.
4.3 The Distortion Problem
Aluminium has a coefficient of thermal expansion that is about twice that of steel, and a thermal conductivity that is about four times that of steel. The combination of high heat input and high expansion means that distortion is a significant problem in thick plate welding.
The solution is to use a strongback or jig to restrain the plate during welding, and to weld in a sequence that balances the heat input—for example, welding from the centre outwards, or using a back-step technique. In my experience, a properly designed jig can reduce distortion by 50–70%.
4.4 The Porosity Problem in Cryogenic Service
The paper's application is air separation equipment, which operates at cryogenic temperatures. Porosity in a weld is not just a structural defect; it is also a potential leak path for cryogenic fluids. A porous weld in a cryogenic service can cause a leak that leads to catastrophic failure.
The countermeasure is to ensure that the weld is fully dense, which requires strict control of hydrogen sources and proper shielding gas coverage. Radiographic testing of 100% of the weld length is mandatory for cryogenic service.
5. Study Insights and Practical Implications
This paper is a valuable reference for anyone involved in welding thick aluminium alloy plate. The author's approach—starting with a material analysis, then designing a groove, then qualifying a procedure, and finally producing a satisfactory joint—is exactly the right methodology for a production environment.
The key takeaway for the practising engineer is that the process parameters are only part of the solution. The real battle is won on the shop floor: clean surfaces, proper jigging, correct preheat, and a welder who understands the material. I have seen too many aluminium welds fail because the welder treated aluminium like steel and expected the same results.
The paper's value lies in its demonstration that a systematic approach to process development yields a reliable weld. It is a modest but useful contribution to the practical literature on aluminium welding, and it deserves a place in the reference library of any shop that regularly fabricates 5083 aluminium plate.
Zhuojin Pipe Fitting Co., Ltd