ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Effect of Intermediate Transition Elements on Microstructure of Mg-Al TIG Fusion Welding

Background and Technical Challenge

Magnesium-aluminum dissimilar welding is one of those problems that has haunted the welding industry for decades. I have seen more than my share of attempts to weld these two metals, and I have seen more than my share of failures. The fundamental problem is that magnesium and aluminum form brittle intermetallic compounds, particularly Al3Mg2 and Al12Mg17, which severely degrade the mechanical properties of the joint. These intermetallics are hard and brittle, and they create stress concentrations that can lead to premature failure.

The study by Liu Zhengjun and his colleagues at Shenyang University of Technology addresses this problem by investigating the use of intermediate transition elements to modify the interface between magnesium and aluminum. The idea is to introduce a third element that can either prevent the formation of the intermetallic compounds or modify their morphology to make them less detrimental.

Experimental Methodology and Materials

The experimental approach used in this study is straightforward but effective. The researchers used TIG welding to deposit AZ31 magnesium alloy onto pure aluminum substrates. Before welding, they pre-placed various transition materials on the aluminum surface: silver (Ag), zinc (Zn), nickel (Ni), and brass (a copper-zinc alloy). The pre-placed materials were intended to act as intermediate layers that would modify the diffusion and reaction between the magnesium and aluminum.

Transition Material Purpose My Practical Comment
None (Direct) Baseline for comparison Shows the direct Mg-Al reaction
Silver (Ag) Potential barrier to Mg-Al diffusion Silver is expensive but has good metallurgical compatibility
Zinc (Zn) Potential barrier to Mg-Al diffusion Zinc is cheaper and more practical for industrial use
Nickel (Ni) Potential barrier to Mg-Al diffusion Nickel is a common plating material
Brass (Cu-Zn) Combined effect of Cu and Zn Brass is cheaper than pure Zn or Ag

The choice of AZ31 magnesium alloy is significant because it is one of the most commonly used magnesium alloys in structural applications. It has good strength and ductility, and it is relatively easy to weld. However, its compatibility with aluminum is poor, which is exactly the problem being studied.

Microstructural Analysis and Findings

The study used scanning electron microscopy (SEM) to analyze the microstructure of the fusion-welded joints. This is the right tool for this type of analysis because it allows the researchers to see the distribution of the intermetallic compounds and the morphology of the phases.

The results showed that when AZ31 was deposited directly onto aluminum without any intermediate layer, the fusion zone had a columnar grain structure, and the diffusion of magnesium and aluminum led to the formation of Al3Mg2 intermetallic compounds. This is consistent with what I have seen in practice. The direct Mg-Al weld is characterized by a brittle intermetallic layer at the interface, which is the primary cause of poor joint strength.

When silver and zinc were used as intermediate layers, the results were significantly different. Both silver and zinc were effective in preventing the diffusion of magnesium and aluminum, which reduced the formation of the intermetallic compounds. This is a significant finding because it suggests that these elements can act as effective diffusion barriers.

However, nickel and brass were not effective in preventing the diffusion and intermetallic compound formation. This is an interesting result. Nickel is a common transition metal that is often used in dissimilar welding, but in this case, it did not provide the expected benefit. The brass, which contains both copper and zinc, also did not perform well, despite the zinc content.

Metallurgical Explanation and Practical Implications

The effectiveness of silver and zinc as diffusion barriers can be explained by their metallurgical properties. Both silver and zinc have good solubility in both magnesium and aluminum, which means they can form solid solutions with both metals. This allows them to create a gradual transition zone rather than a sharp interface. The gradual transition zone reduces the driving force for intermetallic compound formation.

In contrast, nickel has limited solubility in both magnesium and aluminum, which means it tends to form its own intermetallic compounds rather than acting as a diffusion barrier. The brass, which is primarily copper and zinc, may have been ineffective because the copper content promoted the formation of copper-magnesium intermetallics, which are also brittle.

From a practical standpoint, the use of zinc as an intermediate layer is particularly interesting because zinc is relatively inexpensive and easy to apply. Silver, while effective, is expensive and would not be practical for most industrial applications. The use of zinc as a transition layer could potentially enable the welding of magnesium to aluminum in applications where this was previously not feasible.

Lessons Learned and Reflections

This study brings to mind several lessons that I have learned over the years in the welding industry.

The first lesson is that the interface between dissimilar metals is where the action is. In any dissimilar metal weld, the properties of the joint are determined by what happens at the interface. If you can control the interface, you can control the joint properties.

The second lesson is that simple solutions are often the best. The use of a pre-placed intermediate layer is a simple concept, but it can be very effective. In my experience, some of the best welding solutions are the ones that involve simple process modifications rather than complex equipment changes.

The third lesson is that the choice of intermediate material is critical. Not all transition elements are created equal. The effectiveness of an intermediate layer depends on its metallurgical compatibility with both base metals, its ability to form solid solutions, and its cost and availability.

Summary

This study provides valuable insights into the use of intermediate transition elements to control the formation of intermetallic compounds in Mg-Al dissimilar welding. The results show that silver and zinc are effective diffusion barriers, while nickel and brass are not. The practical implications of this research are significant for the welding of magnesium to aluminum, which has been a persistent challenge in the industry. The use of zinc as an intermediate layer is particularly promising because it is inexpensive and effective. As the use of magnesium alloys continues to grow in automotive and aerospace applications, the ability to weld magnesium to aluminum will become increasingly important, and research like this provides the foundation for practical solutions.