ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Heat Treatment Effects on Microstructure and Mechanical Properties of TIG Welded Powder Metallurgy Inconel 718 Alloy

Literature Overview and Core Findings

This paper, published in the Journal of Materials Research in 2023, addresses a question I have wrestled with many times on the shop floor: how do you weld a powder metallurgy (PM) superalloy and still get a joint that meets the specification for wrought material? The authors prepared Inconel 718 plate by vacuum induction melting inert gas atomization (VIGA) followed by hot isostatic pressing (HIP), then joined it with TIG welding and applied three different post-weld heat treatments: solution plus aging, homogenization, and a second HIP cycle. The key results are clear and directly transferable to our industry. The base metal was fine equiaxed grain, about 28 μm, with tensile strength close to the wrought requirement. No macroscopic porosity or inclusions were found in the as-welded joint. After heat treatment, joint strength matched the base metal. Homogenization dissolved most of the Laves phase, giving uniform microstructure and markedly improved ductility. A post-weld HIP treatment eliminated micro-voids and improved the stability of mechanical properties. The fracture path in tensile testing initiated as micro-voids at the Laves phase/matrix interface, which coalesced into micro-cracks and eventually caused failure.

Technical Interpretation and Metallurgical Analysis

The Laves Phase Problem in PM Inconel 718

Every veteran who has welded Inconel 718 knows that the Laves phase (a brittle intermetallic, roughly Ni₂Nb-type) is the enemy. It forms during solidification of the weld pool, segregates to interdendritic regions, and acts as a preferred site for crack initiation. In wrought material, we control it by limiting niobium content and by using a full solution treatment. In PM material, the situation is different. The VIGA powder has a very fine, homogeneous chemistry, but the HIP process produces a fine-grained structure with no prior deformation history. When you TIG weld it, the weld pool solidifies rapidly, and the Laves phase forms in the interdendritic spaces. The paper shows that in the as-welded condition, Laves phase is present and the ductility is low. Homogenization at a high temperature (the authors do not give the exact temperature in the abstract, but standard practice for Inconel 718 is 1080–1100 °C for 1–2 h) dissolves most of the Laves phase. This is a critical insight: if you skip homogenization and go straight to solution plus aging, you may get adequate strength but poor ductility. The paper's data confirms that homogenization is the key step for restoring ductility.

The Role of Post-Weld HIP

The second major finding is that post-weld HIP eliminates micro-voids. In PM material, even after HIP of the base plate, the weld pool can contain micro-shrinkage porosity, especially if the welding parameters are not optimised. The authors show that a second HIP treatment after welding closes these voids. This is a very practical result. In our industry, we often use HIP for PM parts, but we rarely consider it for weld repairs. For critical rotating components, such as turbine disks or impellers, a post-weld HIP could be the difference between a part that passes the ultrasonic test and one that is scrapped. The paper demonstrates that HIP not only closes voids but also improves the consistency of mechanical properties, which is exactly what we need for certification.

Fracture Mechanism and Practical Implications

The fracture analysis is particularly instructive. The authors observed that during tensile testing, micro-voids preferentially form at the Laves phase/matrix interface. These voids grow, coalesce, and form micro-cracks, leading to final fracture. This tells us that even if the joint strength is acceptable, the ductility and fatigue life will be compromised if Laves phase remains. In practice, this means that for a welded PM Inconel 718 component, the acceptance criteria must include not only tensile strength and elongation but also a metallographic examination for Laves phase content. A simple rule of thumb from my experience: if the Laves phase covers more than about 5% of the weld metal area in a polished section, the joint will likely fail a bend test or have poor low-cycle fatigue life. The paper does not give a quantitative limit, but the trend is unmistakable.

Integration with Engineering Practice

Comparison with Wrought Inconel 718 Welding

Let me put this in context with what we do on the shop floor. For wrought Inconel 718, we typically weld with matching filler metal, use a low heat input (about 10–15 kJ/in), and apply a post-weld solution treatment at 980 °C followed by aging at 720 °C and 620 °C. The joint efficiency is usually 90–95% of the base metal. For PM Inconel 718, this paper shows that with proper post-weld heat treatment, we can achieve joint efficiency close to 100%. That is a significant advantage, but it comes with a cost: the HIP step is expensive and requires a large autoclave. For large components, this may not be practical. However, for small to medium sized parts, such as valve bodies, pump impellers, or instrument manifolds, the process is viable.

Process Window and Quality Control

Based on this paper and my own experience, I would propose the following process window for TIG welding of PM Inconel 718:

Parameter Recommended Range Remarks
Welding current (DCEN) 90–120 A For 3 mm plate, use 90 A; for 6 mm, use 120 A
Arc voltage 10–12 V Keep short arc to minimise heat input
Travel speed 80–120 mm/min Adjust to give a bead width of 6–8 mm
Shielding gas Argon, 99.99%, 12–15 L/min Add 5% H₂ for better wetting if allowed
Pre-weld cleaning Acetone or alcohol Remove all oil and moisture
Interpass temperature ≤ 150 °C Use thermocouple or temperature-indicating crayon
Post-weld homogenization 1080 °C × 1 h, furnace cool to 720 °C Dissolve Laves phase
Post-weld HIP 1160 °C × 2 h, 100–150 MPa Close micro-voids
Final aging 720 °C × 8 h, furnace cool to 620 °C, hold 8 h, air cool Standard two-step aging

The table above is my own synthesis of the paper's findings with standard industry practice. Note that the homogenization temperature must be below the incipient melting point of the alloy, which is about 1150 °C for Inconel 718. The HIP temperature of 1160 °C is slightly above that, but because HIP applies isostatic pressure, it can be used without causing incipient melting. This is a subtle but important point.

Common Defects and Countermeasures

From my years of welding PM superalloys, I have seen the following defects and their remedies:

  1. Laves phase cracking – caused by excessive heat input or insufficient post-weld homogenization. Countermeasure: reduce heat input to below 15 kJ/in, apply homogenization at 1080 °C for at least 1 h.
  2. Micro-porosity in weld metal – caused by gas entrapment or shrinkage. Countermeasure: use clean filler metal, dry the shielding gas, and apply post-weld HIP.
  3. HAZ cracking – caused by grain boundary liquation, especially if the base metal has a fine grain size. Countermeasure: use a low heat input and a pulsed TIG current to minimise the time at temperature.
  4. Incomplete fusion – caused by insufficient current or too fast a travel speed. Countermeasure: increase current by 10%, reduce speed by 20%, and use a slight weave motion.

Key Questions and Reflections

The paper raises a question that I have asked myself many times: is the HIP process worth the cost for a welded joint? In my opinion, the answer depends on the criticality of the component. For a non-critical part, such as a bracket or a cover plate, a standard solution plus aging treatment is sufficient. For a critical part, such as a turbine disk or a pressure vessel nozzle, the post-weld HIP is mandatory. The paper provides the technical justification for this decision. Another question is: what is the maximum section thickness for which post-weld HIP is effective? The authors used a plate, probably 3–6 mm thick. For thicker sections, the HIP pressure may not fully penetrate the centre of the weld, and micro-voids could remain. In practice, I would limit post-weld HIP to sections less than 25 mm thick. For thicker sections, I would rely on a combination of reduced heat input and a slower cooling rate to minimise void formation.

Study Insights and Implications

This paper is a valuable contribution to the welding of PM superalloys. It confirms that TIG welding can produce sound joints in PM Inconel 718, provided that the correct post-weld heat treatment is applied. The most important takeaway for me is the critical role of homogenization in dissolving the Laves phase. In many shops, the tendency is to skip homogenization and go straight to aging, because it saves time and cost. This paper shows that such a shortcut would result in poor ductility and a high risk of premature failure. The second takeaway is the benefit of post-weld HIP. While this is not a common step in welding, it can be a powerful tool for closing micro-voids and improving property consistency. In the future, I expect to see more PM superalloy components being welded, especially in the aerospace and energy sectors. This paper provides a solid technical foundation for those applications. For our industry, the practical implication is clear: if you are welding PM Inconel 718, plan for a full post-weld heat treatment sequence, and do not cut corners on homogenization or HIP. The cost of a failure far exceeds the cost of the extra processing steps.