ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Numerical Simulation of Surface Deformation in TIG Weld Pool

Literature Overview

This paper by Zhang Jianbao and Wang Hong from Taiyuan University of Science and Technology presents a numerical simulation of the surface deformation of the weld pool during TIG welding. The work was published in the journal Hot Working Technology in 2016. The authors established a weld pool model that considers the free surface, used a moving double ellipsoid heat source, and employed FLUENT to simulate the stress field on the weld pool surface at different currents. They analysed the effect of arc pressure on the surface deformation of the weld pool and compared the simulation results with experimental data to validate the model.

Core Technical Findings

Model Description

The weld pool model considers the free surface of the molten metal, which is a significant improvement over models that assume a flat surface. The moving double ellipsoid heat source is a well-established model for the heat input from the welding arc. The authors used FLUENT, a computational fluid dynamics (CFD) software, to solve the governing equations for the weld pool.

Model Component Description
Heat source Moving double ellipsoid (Goldak model)
Free surface Considered in the model
Governing equations Navier-Stokes equations, energy equation
Boundary conditions Arc pressure, surface tension, gravity
Solution method FLUENT (finite volume method)

The double ellipsoid heat source model is particularly suitable for TIG welding because it represents the heat distribution of the arc more accurately than a simple point or line source. The model accounts for the fact that the heat input is not uniformly distributed but is concentrated at the front of the arc and trails behind it.

Simulation Results

The simulation results show that the stress distribution on the weld pool surface is symmetric in the direction perpendicular to the weld (left-right) and asymmetric in the direction parallel to the weld (front-back). The stress distribution in the left-right direction follows a parabolic profile, with the maximum stress at the centre of the weld. In the front-back direction, the stress distribution shows a trailing effect: the stress is more concentrated at the front of the weld pool and more diffuse at the tail.

Current Arc Pressure Surface Deformation Stress Gradient
Lower Lower Smaller Lower
Medium Medium Moderate Moderate
Higher Higher Larger Higher

The results also show that the current has a significant effect on the arc pressure and the surface deformation. As the current increases, the arc pressure increases, and the surface deformation of the weld pool increases accordingly. The stress gradient also increases with increasing current.

Validation with Experimental Data

The authors compared the simulation results with experimental data. The comparison showed good agreement, confirming the validity of the model. The validation is important because it demonstrates that the model can be used to predict the weld pool behaviour in practical applications.

Integration with Engineering Practice

Why Surface Deformation Matters

The surface deformation of the weld pool is a critical factor in weld quality. Excessive surface deformation can lead to undercut, lack of fusion, or porosity. The surface deformation is influenced by the arc pressure, the surface tension of the molten metal, and the gravitational force. Understanding the relationship between these factors is essential for controlling the weld quality.

In TIG welding, the arc pressure is relatively low compared to other processes such as plasma welding or laser welding. However, the arc pressure is sufficient to cause significant surface deformation, particularly at high currents. The simulation results show that the surface deformation increases with increasing current, which is consistent with the physical understanding of the process.

Practical Implications for Welding Parameter Selection

The simulation results provide a basis for selecting the welding parameters to achieve the desired weld pool shape. For example, if the weld pool is too deep or too wide, the welding current or the travel speed can be adjusted to reduce the surface deformation. The simulation can be used to optimise the welding parameters for a given application.

The results also highlight the importance of the arc pressure in determining the weld pool shape. The arc pressure is determined by the welding current, the arc length, and the shielding gas flow rate. By controlling these parameters, the welding engineer can control the weld pool shape and the resulting weld quality.

The Role of Simulation in Welding Procedure Development

Simulation is a valuable tool for welding procedure development. It allows the welding engineer to evaluate different welding parameters without the need for expensive and time-consuming welding trials. The simulation can be used to predict the weld pool shape, the penetration depth, and the surface deformation for a given set of welding parameters.

However, simulation is not a substitute for welding trials. The simulation results must be validated with experimental data before they can be used with confidence. The authors' validation of the model is therefore an important contribution.

Key Questions and Reflections

The paper raises an important question about the accuracy of the double ellipsoid heat source model. The model assumes a specific heat distribution, but the actual heat distribution may be different. The authors validated the model with experimental data, but the validation was limited to a specific set of welding conditions. Further validation would be needed for different materials, thicknesses, and welding parameters.

Another question is the treatment of the free surface. The model considers the free surface, but the implementation of the free surface boundary condition is complex. The authors used a specific method for tracking the free surface, but the accuracy of this method may be limited. The free surface is also affected by the surface tension, which is temperature-dependent and may vary across the weld pool.

The paper also raises a question about the applicability of the model to different welding processes. The model was developed for TIG welding, but it could be adapted to other processes such as plasma welding or laser welding. However, the heat source model and the boundary conditions would need to be modified to reflect the different physical processes.

Study Insights