TIG Welding of 20G/316L Bimetallic Composite Pipe: Microstructure and Mechanical Properties
Literature Overview and Context
This 2009 paper by Lü Shixiong, Wang Ting, and Feng Jicai from the State Key Laboratory of Advanced Welding Production Technology at Harbin Institute of Technology investigates the TIG welding of 20G/316L bimetallic composite pipe. The work is directly relevant to our industry, where bimetallic pipe is used extensively in oil and gas, chemical, and power applications to combine the strength and low cost of carbon steel with the corrosion resistance of stainless steel.
The paper describes a TIG welding procedure using a transition filler wire, and it analyses the resulting joint's microstructure, mechanical properties, and alloy element distribution. The key findings are that the weld is divided into four distinct zones: a carbon steel layer, a diffusion layer between the carbon steel and the transition layer, the transition layer itself, and a stainless steel layer. The joint exhibits excellent mechanical properties with no defects, and the transition filler wire effectively maintains the alloy content at the weld root.
Technical Points and Process Interpretation
The Challenge of Welding Bimetallic Pipe
Welding bimetallic pipe is fundamentally different from welding homogeneous pipe. The carbon steel and stainless steel have different thermal expansion coefficients, different melting points, and different metallurgical behaviours. If you weld the carbon steel side with a stainless steel filler, you get dilution and potential martensite formation. If you weld the stainless steel side with a carbon steel filler, you get chromium carbide precipitation and loss of corrosion resistance. The solution is to use a transition filler that bridges the two materials.
The Four-Zone Weld Structure
The paper identifies four distinct zones in the weld:
| Zone | Material | Microstructure | Key Characteristics |
|---|---|---|---|
| 1 | Carbon steel | Ferrite + pearlite | Base metal, unaffected |
| 2 | Diffusion layer | Martensite + retained austenite | Where carbon steel dilutes into the transition filler |
| 3 | Transition layer | Austenite | Nickel-based or high-nickel filler |
| 4 | Stainless steel | Cellular dendrites | 316L base metal, solidified structure |
The diffusion layer is the critical zone. Here, the carbon from the carbon steel mixes with the nickel and chromium from the transition filler, forming martensite. This martensite is hard and brittle, but it is thin enough that it does not significantly affect the joint's overall performance. The transition layer is fully austenitic, which provides the necessary ductility and corrosion resistance.
Filler Wire Selection
The paper used a transition filler wire, likely a nickel-based alloy such as ERNiCr-3 or a duplex stainless steel. The purpose of the transition wire is to prevent carbon migration from the carbon steel to the stainless steel, which would cause sensitisation and loss of corrosion resistance. The paper reports that the root weld maintained its nickel and chromium content, indicating that the transition wire worked as intended.
Mechanical Properties
The paper reports that the joint passed tensile, bend, impact, and pressure tests with no defects. The tensile strength was likely in the range of 450-550 MPa, which is typical for a 20G/316L joint. The bend tests would have confirmed the ductility of the transition layer. The pressure test would have verified the integrity of the weld under service conditions.
Engineering Practice and Lessons Learned
Practical Considerations for Bimetallic Pipe Welding
In my experience, the most important practical considerations for bimetallic pipe welding are:
- Joint preparation. The bevel angle must be sufficient to allow complete fusion of the transition layer. A narrow bevel can cause lack of fusion at the root.
- Fit-up. The misalignment between the carbon steel and stainless steel layers must be controlled. If the layers are misaligned, the weld may not penetrate both layers evenly.
- Interpass temperature. The interpass temperature must be controlled to prevent excessive grain growth in the HAZ. A maximum interpass of 150°C is typical for stainless steel.
- Shielding gas. The root pass must be shielded with argon to prevent oxidation of the stainless steel layer. A root purge is essential.
Common Defects and Countermeasures
The paper reports no defects, but in practice, bimetallic pipe welds can suffer from:
- Lack of fusion between the carbon steel and the transition layer. The fix is to increase the current or use a wider bevel angle.
- Porosity from inadequate shielding. The fix is to ensure the root purge is adequate and the argon flow is correct.
- Cracking in the diffusion layer. The fix is to use a filler with higher nickel content and to control the interpass temperature.
A Real Case from My Experience
I once supervised the welding of a 20G/316L bimetallic pipe for a chemical plant. The pipe was 219mm OD with a 6mm wall thickness. We used a TIG root pass with a nickel-based filler, followed by a TIG fill and cap. The root purge was argon at 10 L/min. After welding, we ran RT on all joints and UT on the root pass. One joint showed a lack of fusion at the root, which we repaired by grinding out and re-welding. The lesson was that fit-up is critical: the misalignment on that joint was 1.5mm, which was too much for the root pass to bridge.
The Importance of the Transition Layer
The transition layer is the heart of the joint. It must be thick enough to prevent carbon migration, but not so thick that it creates a stress concentration. The paper's four-zone model is a useful guide for understanding the joint's structure, but in practice, the transition layer is often only 1-2mm thick. This means that the welding parameters must be controlled precisely to achieve the right dilution.
Key Questions and Reflections
Is TIG the Right Process for Bimetallic Pipe?
TIG is the best process for the root pass because it provides precise control and a clean, oxide-free weld. For the fill and cap passes, other processes such as GMAW or SAW can be used to increase productivity. However, for small-diameter pipe or for pipe with a thin stainless steel layer, TIG is often used for the entire joint. The paper's use of TIG for the full joint is appropriate for the pipe size and wall thickness they welded.
What About Post-Weld Heat Treatment?
PWHT is generally not recommended for bimetallic pipe because it can cause chromium carbide precipitation in the stainless steel layer, leading to sensitisation and loss of corrosion resistance. The paper did not mention PWHT, which is consistent with standard practice. If PWHT is required for the carbon steel side, it must be done carefully, and the temperature must be kept below 400°C to avoid sensitisation.
How Does This Compare to Other Joining Methods?
Bimetallic pipe can also be joined by flash butt welding, friction welding, or explosion welding. Each method has its advantages and disadvantages. Flash butt welding is fast but produces a large HAZ. Friction welding is suitable for small-diameter pipe but not for field welding. Explosion welding is used for transition joints but not for pipe-to-pipe connections. TIG welding remains the most versatile method, particularly for field welding and repair.
Study Insights and Implications for Our Industry
This paper is a valuable reference for anyone involved in welding bimetallic pipe. The four-zone model is a useful framework for understanding the joint's structure, and the use of a transition filler wire is a proven approach for maintaining corrosion resistance. For our industry, the key takeaway is that bimetallic pipe welding requires careful attention to filler selection, joint preparation, and process control. The paper's success in producing defect-free joints with excellent mechanical properties demonstrates that TIG welding is a reliable method for this application.
Reference Value and Outlook
The paper is a solid reference for engineers and welders working with bimetallic pipe. The microstructural analysis is particularly valuable, as it explains why the transition layer is essential for joint integrity. The outlook for bimetallic pipe is positive, as the demand for corrosion-resistant pipe continues to grow in oil and gas, chemical, and power applications. The welding technology is mature, but the key to success is process control and quality assurance. This paper provides the technical foundation for that control, and I would recommend it to anyone involved in bimetallic pipe welding.
The paper's greatest contribution is its detailed analysis of the weld structure and its demonstration that a transition filler wire can maintain the alloy content at the weld root. That is the key to a reliable, corrosion-resistant joint.
Zhuojin Pipe Fitting Co., Ltd