High-Frequency Composite Double-Tungsten TIG Welding Method and Digital Power Supply Development
Overview of the Novel Welding Process
This paper from Nanjing University of Science and Technology presents a new non-consumable electrode composite welding process and the associated digital power supply. The concept is to use two tungsten electrodes simultaneously, with one electrode carrying a high-frequency square wave current and the other carrying a variable polarity square wave pulse current. The high-frequency component is intended to stabilize the arc and provide additional heat input, while the variable polarity component is intended to provide the cleaning action that is essential for welding aluminum and magnesium alloys. This is a clever combination of two known techniques, and the paper focuses on the design and performance of the power supply, which is the critical enabling technology.
Power Supply Design and Performance
The power supply is designed to output two current waveforms simultaneously. The first is a high-frequency square wave current with a base current of 0-300 A, a peak current of 0-100 A, a frequency of 0-80 kHz, a duty cycle of 0-100%, and a pulse current rate of change up to 50 A/μs. The second is a variable polarity square wave pulse current with positive and negative half-wave amplitudes of 0-500 A, a frequency of 0-100 Hz, a duty cycle of 0-100%, and a variable polarity current rate of change up to 300 A/ms. The test results confirm that the power supply meets the design targets, and that the high-frequency square wave current maintains fast rise and fall times even at 80 kHz.
| Parameter | High-Frequency Channel | Variable Polarity Channel |
|---|---|---|
| Current type | Square wave | Variable polarity square wave |
| Base current | 0-300 A | N/A |
| Peak current | 0-100 A | 0-500 A |
| Frequency | 0-80 kHz | 0-100 Hz |
| Duty cycle | 0-100% | 0-100% |
| Current rate of change | Up to 50 A/μs | Up to 300 A/ms |
The ability to deliver 80 kHz square wave current with fast rise and fall times is a significant technical achievement, because it requires a power supply with very low inductance and fast switching capabilities. This is the kind of technology that was not available in the 1990s, and it represents a genuine advancement in welding power supply design.
Process Demonstration on Aluminum
The paper demonstrates the process by performing a bead-on-plate weld on an aluminum alloy plate. The results show that the welding process is stable and the weld bead formation is good. This is a positive indication, but it is important to note that bead-on-plate welding is a relatively simple test. The real challenge is applying this process to actual joint configurations, such as butt joints, lap joints, or fillet welds, where the arc stability and heat input control are more demanding. The variable polarity component is particularly important for aluminum, because it provides the cathodic cleaning action that removes the oxide layer from the surface of the aluminum, which is essential for achieving good fusion.
Engineering Practice and Lessons Learned
From a practical standpoint, this process has the potential to improve welding productivity and quality, but it also introduces significant complexity. The power supply is a sophisticated piece of equipment, and it requires precise control of two independent current waveforms. This means that the operator must be highly skilled, and the process parameters must be carefully optimized for each application. In my experience, the transition from a laboratory demonstration to a production application is often difficult, because the process window is narrow and the equipment is expensive. However, for high-volume production of aluminum or magnesium components, the potential benefits in terms of welding speed and quality could justify the investment. The high-frequency component is particularly interesting, because it may allow for higher welding speeds without sacrificing weld quality, which is a key driver of productivity.
Concluding Remarks
This paper presents a novel and technically sound approach to TIG welding, combining high-frequency and variable polarity current waveforms to achieve stable arcs and good weld quality. The power supply design is the key contribution, and the demonstration on aluminum is a promising first step. For the pipe and fitting industry, this technology is not immediately applicable, because most of our welding is on steel and the economics are different. However, the principles of high-frequency arc stabilization and variable polarity cleaning are relevant to any non-consumable electrode welding application, and I would recommend this paper to anyone involved in the welding of aluminum or magnesium alloys. The next step would be to demonstrate the process on actual joint configurations and to establish a process window for production use.
Zhuojin Pipe Fitting Co., Ltd