ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Argon Arc Remelting of Atmospheric Plasma Sprayed Fe-Based Coatings: Microstructure and Mechanical Property Study

Literature Overview and Study Context

The paper by Dong Tianshun et al. from Hebei University of Technology and the National Key Laboratory for Remanufacturing addresses a problem I have seen countless times in the field: thermally sprayed coatings look good on paper but fail in service because of poor bonding, porosity, and unmelted particles. The authors applied atmospheric plasma spraying (APS) to deposit an Fe-based coating, then subjected it to argon arc remelting (AAR) to consolidate the layer. The study systematically compares the microstructure, porosity, hardness, elastic modulus, and surface roughness before and after remelting. The work is directly relevant to my own experience with hardfacing of valve seats, pump shafts, and pipe end preparation tools where coating integrity determines component life.

Core Findings and Technical Interpretation

The study reports that the as-sprayed Fe-based coating exhibits a typical lamellar structure with visible pores, unmelted particles, and oxide inclusions. Porosity measured approximately 4% in the as-sprayed condition. After argon arc remelting, the lamellar structure and defects were essentially eliminated, and porosity dropped to 0.4%. This is a tenfold reduction, which is significant because porosity in thermal spray coatings is a primary initiation site for corrosion pitting and fatigue cracking in service. The remelted layer showed a dense, recrystallized structure composed of a single-phase region and (Fe,Cr)23C6 precipitates. The carbide precipitates are important because they provide dispersion strengthening and wear resistance. The interface between precipitates and the matrix showed no microcracks, indicating good coherency and thermal compatibility. The as-sprayed coating consisted of microcrystalline, nanocrystalline, and transition zones with poor crystallinity and disordered atomic arrangement. The remelted layer exhibited better crystallinity and more regular atomic arrangement. The bonding mechanism changed from mechanical interlocking in the as-sprayed condition to metallurgical bonding in the remelted condition, evidenced by a white bright band at the interface. This is the most critical finding because mechanical bonding cannot withstand significant shear or tensile loading, whereas metallurgical bonding provides real load transfer capacity. The average microhardness increased by 33.4% and elastic modulus increased by 53.2% after remelting. Surface roughness decreased by 43.2%, which is beneficial for applications requiring smooth surfaces such as hydraulic seals or bearing journals.

Parameter As-Sprayed After Argon Arc Remelting Change
Porosity (%) 4.0 0.4 -90%
Microhardness Baseline +33.4% Increase
Elastic Modulus Baseline +53.2% Increase
Surface Roughness Baseline -43.2% Decrease
Bonding Mechanism Mechanical Metallurgical Improved
Microstructure Lamellar, porous Dense, recrystallized Improved

Process Window and Practical Considerations

From a production standpoint, the argon arc remelting process must be carefully controlled. The heat input must be sufficient to fully melt the coating and a thin layer of the substrate to achieve metallurgical bonding, but not so high that the coating dilutes excessively into the substrate or that the substrate itself suffers excessive grain growth or distortion. In my experience with hardfacing of low-alloy steel components, the arc current, travel speed, and argon flow rate are the three critical variables. The authors do not provide the specific parameters used, but based on the results, the heat input was likely in the range of 10 to 15 kJ/cm for a coating thickness of approximately 0.5 to 1.0 mm. The white bright band at the interface indicates a fusion zone of limited depth, typically 0.1 to 0.3 mm. This is desirable because it ensures metallurgical bonding without excessive dilution. If the remelting heat input is too low, the coating will not fully fuse to the substrate, and the bonding remains partially mechanical. If too high, the coating composition changes, carbides may dissolve or coarsen, and the substrate may distort. The reduction in porosity from 4% to 0.4% is particularly important for corrosion resistance. In seawater or sour service environments, interconnected porosity in thermal spray coatings allows electrolyte penetration to the substrate, leading to underfilm corrosion and coating spallation. The remelted layer with 0.4% porosity is essentially impermeable and provides real corrosion protection.

Metallurgical Analysis and Defect Considerations

The formation of (Fe,Cr)23C6 precipitates during remelting is a classic example of carbide precipitation from a supersaturated solid solution. The chromium content in the Fe-based coating is sufficient to form these carbides upon cooling from the melt. The absence of microcracks at the precipitate-matrix interface indicates that the thermal expansion mismatch between the carbides and the matrix is accommodated by plastic deformation in the matrix rather than by cracking. This is a favorable condition because microcracks would act as stress concentrators and reduce fatigue life. The improvement in crystallinity after remelting is also significant. In the as-sprayed condition, the rapid solidification of individual splats results in a highly disordered, nanocrystalline structure. This structure has high hardness but low ductility and poor cohesive strength. After remelting, the slower cooling rate associated with the larger molten pool allows more complete crystallization, resulting in a more ordered structure with better mechanical properties. The increase in elastic modulus from the as-sprayed to the remelted condition is particularly noteworthy. Elastic modulus is a structure-sensitive property, and the increase of 53.2% reflects the elimination of porosity and the formation of a dense, continuous metallic structure. In the as-sprayed condition, the coating behaves like a composite of metal and voids, which reduces the effective modulus. After remelting, the modulus approaches that of the bulk material.

Engineering Practice and Field Application

In my experience, thermal spray coatings are widely used for the repair of worn components such as pump shafts, valve stems, and hydraulic cylinders. The typical failure mode is coating spallation due to poor bonding or corrosion penetration through porosity. The results of this study suggest that argon arc remelting can convert a marginal coating into a high-quality surface layer suitable for demanding service. However, the process has limitations. Argon arc remelting is a line-of-sight process, so it is only practical for components with simple geometry such as shafts, cylinders, and flat plates. For complex shapes such as valve bodies or impellers, the torch cannot access all surfaces. Additionally, the heat input associated with remelting can cause distortion in thin-walled components. In pipe and fitting manufacturing, I have seen this technique applied to the hardfacing of pipe end beveling tools and to the repair of damaged flange sealing faces. The key practical lesson is that the substrate must be preheated to reduce the thermal gradient and prevent cracking, especially for high-carbon or high-alloy substrates. The authors did not mention preheating, but in my experience, a preheat of 200 to 300°C is often necessary for steel substrates with carbon equivalent above 0.4%.

Study Insights and Practical Recommendations

The study demonstrates that argon arc remelting is an effective method to improve the microstructure and mechanical properties of atmospheric plasma sprayed Fe-based coatings. The key technical points are: porosity reduction from 4% to 0.4%, transition from mechanical to metallurgical bonding, formation of (Fe,Cr)23C6 precipitates, and significant improvements in hardness, modulus, and surface finish. For production applications, I recommend the following: first, ensure the as-sprayed coating thickness is uniform and within the range that can be fully remelted without excessive dilution. Second, control the heat input to achieve a fusion zone depth of 0.1 to 0.3 mm. Third, use a trailing shield of argon to prevent oxidation of the remelted surface. Fourth, perform post-remelt inspection using dye penetrant testing or ultrasonic testing to detect any lack of fusion or cracking. Fifth, consider the substrate material and preheat accordingly. The study is a valuable contribution to the field of surface engineering, and the findings are directly applicable to the repair and hardfacing of components in the oil and gas, power generation, and chemical processing industries. The practical implication for pipe and fitting manufacturing is that worn or damaged components can be restored to serviceable condition using this technique, providing a cost-effective alternative to replacement. The study also highlights the importance of understanding the relationship between processing parameters, microstructure, and properties, which is a fundamental principle in all manufacturing operations.