ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Numerical Simulation of Temperature Field in Preheating-Free TIG Welding of Copper

Literature Overview and Context

This paper by Lei Yucheng and colleagues from Jiangsu University addresses a persistent headache in our industry: welding thick copper without preheating. The work was supported by a National 863 Program grant, which tells you this was considered strategically important research. Copper has a thermal conductivity roughly 10 times that of carbon steel, which means heat dissipates so rapidly that achieving fusion in thick sections conventionally requires substantial preheating—often 300-500°C—or high-energy processes like electron beam or laser welding. The authors set out to prove that a properly engineered TIG process using Ar+N2 mixed shielding gas could eliminate the preheat requirement entirely.

The paper develops a three-dimensional transient numerical model of the TIG welding molten pool under a moving arc, incorporating the enthalpy concept and a double-elliptical heat source distribution. This is not just academic exercise; the model was validated against actual weld cross-sections, and the calculated fusion boundary profiles matched measured values closely. The key innovation is the use of Ar+N2 shielding gas, which increases arc thermal efficiency by leveraging the exothermic dissociation and recombination of nitrogen in the arc plasma. When N2 molecules dissociate into atomic nitrogen in the high-temperature arc, they absorb energy; when they recombine at the cooler workpiece surface, they release that energy back, effectively transferring more heat to the base metal than pure argon can achieve.

Technical Points and Process Windows

Heat Source Modeling and Thermal Efficiency

The double-elliptical heat source model is a critical refinement over simpler Gaussian models. In TIG welding, the arc is not radially symmetric when the torch moves—the heat input distribution is elongated in the direction of travel, with a steeper gradient at the leading edge and a more gradual fall-off at the trailing edge. The authors captured this asymmetry, which matters greatly for predicting molten pool shape in a material with copper's thermal diffusivity.

Parameter Value / Description
Base material Pure copper (T2 or equivalent), thick section
Welding process DC TIG, no preheat
Shielding gas Ar + N2 mixture (specific ratio not disclosed in abstract, typically 20-30% N2)
Heat source model Double-elliptical surface distribution
Numerical approach 3D transient, enthalpy-based formulation
Validation Computed fusion boundary vs measured weld cross-section

The enthalpy method is particularly apt for phase-change problems. Instead of tracking a moving solid-liquid interface explicitly, the enthalpy formulation treats latent heat as part of the total enthalpy, allowing a fixed-grid solution. For copper, which has a high latent heat of fusion (approximately 205 kJ/kg), this approach avoids the numerical instability that would arise from a sharp interface tracking method.

Experimental Validation and Practical Implications

The experimental results confirmed that the Ar+N2 mixture significantly enhances arc thermal effects, making preheat-free TIG welding of thick copper feasible. The authors established relationships between process parameters and weld penetration depth and width. This is exactly the kind of data a welding engineer needs when setting up a procedure qualification.

In my own experience with copper-nickel alloy piping for marine and offshore applications, I have seen the practical consequences of ignoring these fundamentals. Copper-nickel 90/10 and 70/30 pipes are routinely welded with GTAW using argon shielding, and preheating is often specified for wall thicknesses above 10 mm. The problem is that preheating copper-nickel in the field is a logistical nightmare—you need induction heaters, thermocouples, and a controlled cooling regime, all of which add hours to the welding cycle and create quality risks if the preheat is uneven.

The Ar+N2 approach offers an elegant alternative. I have seen shops in Japan and Korea use nitrogen additions to argon for copper welding with excellent results. The nitrogen dissociates in the arc, absorbs energy, and then recombines at the workpiece, releasing that energy precisely where it is needed—at the fusion boundary. This is not magic; it is physics. The arc becomes a more efficient heat transfer medium.

Engineering Practice and Lessons Learned

Defect Concerns with Nitrogen-Shielded Copper Welds

Before anyone rushes to adopt Ar+N2 shielding for copper, I want to flag a real concern: nitrogen porosity. Copper has a very low solubility for nitrogen in the solid state, and if the nitrogen content in the shielding gas is too high, or if the welding speed is too fast, nitrogen can be trapped as gas bubbles in the solidifying weld metal. This is a classic defect in copper welding, and it is the reason many specifications still call for pure argon.

The paper's success suggests that the nitrogen content was carefully optimized—likely in the range of 15-30% by volume. Above that, porosity risk increases significantly. Below that, the thermal benefit diminishes. The authors do not provide the exact ratio in the abstract, but the principle is clear: there is an optimum window, and it must be established experimentally for each base metal composition and thickness.

What This Means for Pipe and Fitting Fabrication

For our industry, the practical implications are substantial. Consider a 20 mm thick copper busbar or a copper-nickel pipe header for a seawater cooling system. With conventional TIG and pure argon, you would need preheat at 300°C or more, and you would likely need multiple passes with interpass temperature control. With Ar+N2 shielding, you might achieve full penetration in fewer passes, with no preheat, and with a narrower heat-affected zone.

The heat-affected zone in copper is a critical concern. Copper does not undergo phase transformations like steel, but excessive heat input can cause grain growth and a corresponding loss of ductility. The numerical model allows the welding engineer to predict the thermal cycle at any point in the HAZ, and thus to estimate the grain size and mechanical properties that will result. This is the real value of simulation—not as a replacement for experiments, but as a tool to reduce the number of experiments needed to establish a robust procedure.

A Caution on Model Limitations

I would be remiss not to mention the limitations of the model. The double-elliptical heat source is a surface distribution, which assumes that the arc heat is deposited at the top surface. In reality, the arc pressure causes surface depression, and the heat input is distributed through the thickness of the molten pool. For thin sections, this simplification is acceptable; for thick sections, it introduces error. The authors validated against relatively thick sections, which suggests the model performed well, but I would want to see more validation data across a range of thicknesses before relying on it for production.

Study Insights and Implications

This paper reinforces a principle that I have learned over decades of welding copper and its alloys: the shielding gas is not just a protective envelope—it is an active participant in the heat transfer process. Reactive gases like nitrogen and hydrogen can be used deliberately to enhance arc thermal efficiency, but they must be balanced against the risk of porosity and other defects.

For the pipe and fitting industry, the practical takeaway is that preheat-free TIG welding of thick copper is achievable with the right gas mixture and process parameters. This has direct implications for fabrication cost, cycle time, and quality control. A shop that can weld copper without preheat has a significant competitive advantage, especially for large-diameter copper-nickel piping systems where induction preheating is impractical.

The numerical model developed in this paper is a valuable tool for process development. It allows the welding engineer to explore the parameter space virtually, identifying promising combinations of current, voltage, travel speed, and gas composition before committing to expensive experimental trials. In an industry where procedure qualification costs can run into the tens of thousands of dollars, this is not a trivial benefit.

My advice to fellow engineers is to take this work seriously, but to verify it in your own shop with your own materials. Copper compositions vary, and the optimum nitrogen content will vary with them. Start with 20% N2, weld a test coupon, section it, and measure the penetration. Then adjust. The model will tell you where to look, but the final answer always comes from the weld itself.

The deeper lesson is that we should not accept conventional wisdom—"copper must be preheated"—without questioning it. The physics says otherwise, and this paper proves it with both simulation and experiment. That is the kind of insight that separates a good welding engineer from a great one.