Development of Square-Wave AC Pulsed TIG Welding Machine
Literature Overview and Core Viewpoint
This paper by Hang Zhengxiang and Liu Guiqiu, published in Welding in 1995, describes the design and development of a square-wave AC pulsed TIG welding machine. The authors detail the main circuit and control system, using thyristors as power regulation elements and electronic circuitry for control. The machine is capable of both AC pulsed and DC TIG welding, with the square-wave AC output providing distinct advantages for welding aluminum and its alloys. The core viewpoint is that the square-wave AC waveform, with its rapid zero-crossing and controllable positive and negative half-cycle times, offers superior arc stability and oxide cleaning action compared to conventional sinusoidal AC. This is a foundational paper that explains the principles behind a machine type that is now standard in aluminum welding.
Technical Interpretation of the Key Points
The key technical innovation is the use of thyristors to generate a square-wave AC output. Unlike a sinusoidal waveform, which spends a significant amount of time near zero current, a square wave switches rapidly between the positive and negative peaks. This is critical for aluminum welding because the oxide layer on the surface must be broken down during the positive half-cycle (when the electrode is positive, and the workpiece is negative, which is known as "electrode positive" or "reverse polarity"). The square wave ensures that the cleaning action is intense and uniform, while the negative half-cycle (electrode negative) provides deep penetration. The ability to adjust the balance between the positive and negative half-cycles is a key feature, allowing the welder to optimize the cleaning action versus penetration for a given application. The table below summarizes the typical waveform characteristics.
| Waveform Parameter | Sinusoidal AC | Square-Wave AC | Practical Implication |
|---|---|---|---|
| Zero-Crossing Time | Slow, ~10–20% of cycle | Fast, < 1% of cycle | More stable arc, less re-ignition delay |
| Positive Half-Cycle (Cleaning) | Fixed, 50% | Adjustable, 20–80% | Control of oxide removal vs. penetration |
| Negative Half-Cycle (Penetration) | Fixed, 50% | Adjustable, 20–80% | Control of weld depth and heat input |
| Pulsing Capability | Not available | Available, 0.5–20 Hz | Better control of weld pool and grain size |
| Arc Stability | Moderate | High | Less arc wander, smoother weld bead |
Integration with Engineering Practice
This paper is a classic reference for anyone who has ever struggled to weld aluminum. In my experience, the biggest problem with conventional sinusoidal AC TIG is arc instability, which manifests as a "buzzing" sound and a wandering arc that produces a rough, irregular weld bead. The square-wave machine solves this problem by ensuring that the current is at its peak value for the majority of each half-cycle, which keeps the arc column stable. The pulsing capability is a further refinement that allows the welder to control the weld pool by alternating between a high "peak" current and a low "background" current. This is particularly useful for welding thin aluminum sections, where the heat input must be carefully controlled to prevent burn-through. The paper's design, using thyristors, is somewhat dated by modern standards, as IGBTs (insulated gate bipolar transistors) are now the standard power semiconductor for welding machines. However, the control principles remain the same, and a modern machine using IGBTs with a digital controller can achieve even better waveform control.
Key Questions and Reflections
The paper does not discuss the practical challenges of setting up the machine for a specific application. In my experience, the balance control is the most critical parameter. For a 5 mm thick aluminum plate, I would typically set the balance to 30% positive and 70% negative, which provides sufficient cleaning action while maximizing penetration. If the positive half-cycle is too long, the tungsten electrode will overheat and melt, contaminating the weld. If it is too short, the oxide layer will not be fully removed, leading to lack of fusion and porosity. The pulsing frequency is also critical; for a manual weld, a frequency of 1–2 Hz is typical, while for an automatic weld, a higher frequency of 5–10 Hz can be used to achieve a finer grain structure. Another reflection is on the choice of shielding gas. The paper does not mention this, but for aluminum TIG welding, a mixture of argon and helium (typically 25–75% helium) is often used to increase the heat input and improve penetration. The square-wave machine is compatible with this gas mixture, but the flow rate must be increased to compensate for the lower density of helium.
Study Insights and Outlook
This paper provides a solid foundation for understanding the principles of square-wave AC TIG welding, and the design methodology is still relevant today. The insight I take from it is that the waveform shape is a powerful tool for controlling the welding process, and the ability to adjust the balance and pulse frequency gives the welder a level of control that is not possible with a conventional sinusoidal machine. The outlook for this technology is positive; modern inverter-based machines have made square-wave AC TIG welding more accessible and affordable, and the technique is now standard in the fabrication of aluminum pipe, fittings, and structures. I would recommend this paper to any engineer who is new to aluminum welding and wants to understand the fundamental principles behind the equipment they are using. It is a timeless reference that explains the "why" behind the "how" of aluminum TIG welding, and the lessons it teaches are just as applicable today as they were when it was published.
Zhuojin Pipe Fitting Co., Ltd