ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Magnesium Alloy to Stainless Steel TIG Brazing: Interface Microstructure and Joint Integrity

Literature Overview and Core Findings

Kong Lingming, Du Shuangming, Han Yun and Liu Xiaoqing from Xi'an University of Science and Technology published this work in Mining and Metallurgical Engineering (2017, Vol. 37, No. 5, pp. 118–121). They investigated the lap joint brazing of AZ31B magnesium alloy to 304 stainless steel using tungsten inert gas (TIG) welding with a brass interlayer. The welding parameters were AC current of 70 A, argon gas flow of 15 L/min, and welding speed of 1.5 mm/s. They examined the interface microstructure and element distribution to understand the bonding mechanism.

The results showed that the joint interface consists of three distinct zones: a spreading zone, a shrinkage-crack zone and an oxidation zone. In the spreading zone, the magnesium alloy wets and spreads well on the stainless steel surface, forming an effective bond with the strongest interfacial strength. In the shrinkage-crack zone, some positions have gaps formed by contraction, which weakens the interfacial bond and reduces strength below that of the spreading zone. In the oxidation zone, the magnesium alloy is oxidised and only forms a weak connection with the stainless steel surface, resulting in the lowest bond strength. The addition of the brass interlayer enhances the wetting and spreading of magnesium on stainless steel, increases the length of the spreading zone, and thereby increases the interfacial bond strength.

Technical Interpretation and Metallurgical Analysis

This is a classic dissimilar metal joining problem, and the paper does a good job of identifying the failure modes. Magnesium and stainless steel are metallurgically incompatible: they have very different melting points (650°C for AZ31B versus 1400–1450°C for 304), different thermal expansion coefficients, and no mutual solubility. Direct fusion welding would produce brittle intermetallic compounds such as Mg₂Ni and Mg₁₇Al₁₂, which are catastrophic for joint integrity. TIG brazing with a filler that melts at a lower temperature than the base metal is the correct approach.

The three-zone interface structure is the key finding. Let me explain what each zone means in metallurgical terms:

Zone Formation Mechanism Bond Strength Practical Consequence
Spreading zone Good wetting and spreading of molten Mg alloy on stainless steel surface Strongest Effective load transfer, acceptable joint
Shrinkage-crack zone Contraction gaps during solidification Intermediate Reduced load-bearing area, potential leak path
Oxidation zone Mg oxidised before bonding, weak van der Waals or mechanical interlocking only Weakest No effective bond, likely failure initiation site

The spreading zone is the only region where true metallurgical bonding occurs. In this zone, the molten magnesium alloy reacts with the stainless steel surface, forming a thin intermetallic layer that is strong enough to transfer load. The brass interlayer plays a critical role here: it lowers the surface tension of the molten magnesium, allowing it to spread more easily over the stainless steel surface. This increases the length of the spreading zone and, consequently, the total bonded area.

The shrinkage-crack zone is a classic solidification problem. As the magnesium alloy solidifies and cools, it contracts more than the stainless steel because of its higher thermal expansion coefficient. If the joint geometry does not allow for this contraction, gaps form at the interface. These gaps are not necessarily through-thickness defects, but they reduce the effective bonded area and create stress concentrations. In a lap joint, this zone is particularly vulnerable because the shear load is transferred across the entire interface, and any reduction in bonded area directly reduces joint strength.

The oxidation zone is the most dangerous. Magnesium is highly reactive and oxidises rapidly at elevated temperatures, even in a nominally inert argon atmosphere. If the shielding gas flow is insufficient or the joint is not properly cleaned, the magnesium surface oxidises before it can wet the stainless steel. The oxide layer prevents any metallurgical bonding, and the joint relies only on mechanical interlocking or van der Waals forces. This zone has essentially no strength and is the most likely site for crack initiation and propagation.

Practical Implications for Dissimilar Metal Joints

This research has direct relevance to industries where magnesium and stainless steel must be joined, such as aerospace, automotive, electronics and heat exchanger manufacturing. In our pipe and fitting business, we encounter dissimilar metal joints less frequently, but the principles are universal. When we weld carbon steel to stainless steel, or aluminium to steel, we face the same fundamental challenges: different melting points, different thermal expansion, and the formation of brittle intermetallics.

The brass interlayer is an interesting choice. Brass (copper-zinc alloy) has a melting point of approximately 900–1000°C, which is above the melting point of magnesium but below that of stainless steel. It acts as a transition layer that promotes wetting without forming excessive intermetallics. However, the use of brass introduces copper into the joint, which can be problematic in certain service environments. Copper is susceptible to stress corrosion cracking in ammonia-containing atmospheres and can cause galvanic corrosion when coupled with magnesium or aluminium. This must be considered during material selection.

From a process control perspective, the three-zone structure tells us that the welding parameters must be carefully balanced. Too little heat input and the spreading zone will be short, resulting in a weak joint. Too much heat input and the magnesium will oxidise or even burn through, creating a large oxidation zone. The AC current of 70 A and welding speed of 1.5 mm/s represent a narrow process window, and any deviation will shift the balance between the three zones.

Lessons Learned and Engineering Practice

I have seen similar problems in our own shop when welding aluminium to stainless steel for transition joints. The key lessons are:

  1. Surface preparation is absolutely critical. Both the magnesium and stainless steel surfaces must be cleaned immediately before welding. Any oxide, oil or moisture will promote the formation of the oxidation zone and reduce joint strength. We use a dedicated cleaning station with solvent degreasing followed by wire brushing, and we weld within one hour of cleaning.
  2. Shielding gas coverage must be verified. Magnesium is so reactive that even a small amount of air in the shielding gas will cause oxidation. We use a gas flow meter and a smoke test to verify that the shielding gas is properly covering the weld zone before starting production.
  3. Joint geometry must accommodate thermal contraction. The shrinkage-crack zone is caused by the mismatch in thermal expansion. We design lap joints with a small gap to allow for contraction, or we use a fillet weld geometry that provides more flexibility.
  4. The brass interlayer is not a substitute for good process control. It improves wetting, but it does not eliminate the need for clean surfaces and proper shielding. In fact, the brass itself can oxidise if the shielding is inadequate, which would make the problem worse.

Study Insights and Reference Value

This paper is a valuable contribution to the field of dissimilar metal joining. The three-zone interface model is a practical framework for understanding joint quality, and it provides clear guidance for process development. The finding that the brass interlayer increases the spreading zone length is particularly useful, as it suggests a simple and effective way to improve joint strength.

For engineers working on dissimilar metal joints, I would recommend the following approach:

  1. Characterise the interface microstructure for your specific material combination and welding parameters.
  2. Identify the critical zones (spreading, shrinkage-crack, oxidation) and determine which one controls joint strength.
  3. Optimise the process parameters to maximise the spreading zone and minimise the shrinkage-crack and oxidation zones.
  4. Validate with mechanical testing and non-destructive examination.

The process window is narrow, so I strongly recommend statistical process control (SPC) for any production application. Monitor the welding current, gas flow and welding speed continuously, and use control charts to detect any drift. In my experience, the most common cause of dissimilar metal joint failure is not a fundamental design flaw but a loss of process control — a slight change in gas flow, a dirty surface, or a worn tungsten electrode.

In summary, this work provides a clear and practical understanding of the interface structure in magnesium/stainless steel TIG brazed joints. The three-zone model is a valuable diagnostic tool, and the brass interlayer offers a viable route to improved joint strength. The key to success is meticulous process control and surface preparation, which is a lesson that applies to all dissimilar metal welding. I would encourage engineers to study this paper and then apply its principles to their own material combinations, always validating with actual joint testing.