ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Cast Iron Surface TIG Remelting: Crack Formation Mechanisms and Prevention Measures

Metallurgical Background and the Problem Statement

I have spent more than thirty years in the pipe and fitting business, and I have seen more than my share of cast iron components that needed surface treatment. The paper by Yang Deliang and his colleagues at the Shandong Academy of Metallurgical Science addresses a problem that every foundry and repair shop has wrestled with: how to improve the surface properties of grey cast iron without cracking it. The authors studied TIG remelting of grey cast iron with different matrix structures, and their findings are directly relevant to anyone who has ever tried to salvage a cast iron valve body, a pump casing, or a large flange that has worn out in service.

Grey cast iron is a difficult material to work with because of its flake graphite structure. The graphite flakes act as stress concentrators and provide easy paths for crack propagation. When we remelt the surface with a TIG arc, we create a small molten pool that rapidly solidifies. The cooling rate is high, and the carbon in the iron can form cementite or even martensite in the remelted layer. These hard, brittle phases are the primary cause of cracking. The authors systematically studied the crack forms and their formation causes, and they proposed prevention measures based on process parameters, matrix structure, and preheating temperature.

Crack Formation Mechanisms in the Remelted Layer

The authors identified several crack types in the remelted layer, and their analysis aligns with what I have observed on the shop floor. The cracks can be classified as solidification cracks, hydrogen-induced cracks, and stress-relief cracks. Solidification cracks form during the final stage of solidification when the remaining liquid film is unable to accommodate the thermal contraction strain. Hydrogen-induced cracks are less common in TIG remelting because the arc is relatively short and the hydrogen content is low, but they can occur if the base metal contains moisture or oil contamination. Stress-relief cracks are the most common type in practice, and they form when the residual stresses in the remelted layer exceed the strength of the material.

The key metallurgical factor is the formation of ledeburite in the remelted layer. Ledeburite is a eutectic structure consisting of austenite and cementite, and it is extremely hard and brittle. When the cooling rate is high, the carbon in the molten pool does not have enough time to precipitate as graphite, so it forms cementite instead. This cementite-rich layer has a high hardness but very low ductility. When the remelted layer cools further, the thermal contraction of the substrate and the remelted layer are different, and the resulting tensile stress can easily exceed the fracture strength of the ledeburite layer. The cracks then propagate through the brittle layer and can even extend into the heat-affected zone.

The matrix structure of the base metal plays a critical role. The authors studied grey cast iron with ferritic, pearlitic, and ferritic-pearlitic matrices. The pearlitic matrix has a higher carbon content and a higher hardness, which means it is more prone to cracking during remelting. The ferritic matrix is softer and more ductile, so it can accommodate more of the thermal strain. This is an important practical point: if we are remelting a cast iron component that has a pearlitic matrix, we need to be more careful with the process parameters.

Prevention Measures and Practical Application

The authors proposed three main prevention measures, and I would like to add some practical observations based on my own experience in the field.

Prevention Measure Recommended Practice Practical Effect
Process parameters Use lower welding current, higher welding speed, and shorter arc length Reduces the heat input and the size of the molten pool, which reduces the thermal gradient and the residual stress
Matrix structure Select a base metal with a ferritic matrix if possible, or pre-treat the surface to reduce the carbon content A ferritic matrix is more ductile and can accommodate more thermal strain without cracking
Preheating temperature Preheat the component to 200-300 °C before remelting Reduces the temperature gradient between the remelted layer and the substrate, which reduces the thermal stress

The process parameters are the most important factor in practice. I have seen many cases where a welder used too high a current because he wanted to get a deeper remelted layer, and the result was a network of cracks across the entire surface. The welding current should be selected based on the thickness of the remelted layer required, but it should never exceed the limit that causes excessive dilution of the base metal. The welding speed should be as high as possible while still maintaining a stable arc and a continuous remelted layer. A short arc length is also beneficial because it concentrates the heat and reduces the width of the heat-affected zone.

Preheating is a simple but effective measure. I have used preheating to remelt cast iron valve bodies that had worn out in the seat area, and the difference is remarkable. Without preheating, the remelted layer often cracks within minutes of cooling. With preheating to 250 °C, the remelted layer remains intact, and the component can be returned to service. The preheating temperature should be maintained during the entire remelting process, and the component should be cooled slowly after the operation. Rapid cooling after remelting is the enemy of a crack-free surface.

Conclusion and Engineering Implications

This paper is a valuable reference for anyone involved in the repair or surface treatment of cast iron components. The authors have clearly identified the crack formation mechanisms and proposed practical prevention measures. In my experience, the most important lesson is that the process parameters must be carefully controlled, and preheating should be considered mandatory for components with a pearlitic matrix. The remelted layer will always have some residual stress, but with the right combination of process parameters and preheating, the stress can be kept below the fracture threshold. I would also add that post-remelting stress relief, such as a low-temperature tempering treatment, can further reduce the risk of delayed cracking. This is a technique that has served me well in the repair of pump casings and valve bodies, and I recommend it to any engineer facing a similar challenge.