Special Machine Tool for Connecting Rod Machining — Process Concentration in Practice
1. Why a Special Machine Was Needed
The 2020 paper by Liu Yuelei from Shanghai Civil Aviation College describes a special machine tool designed for machining connecting rod bolt holes and big/small end holes. The motivation is clear: the existing process had low efficiency, low yield, and insufficient precision. This is a common problem in automotive component manufacturing. When you have a high-volume product like a connecting rod, you cannot afford to have a process that produces 95% yield and requires multiple setups. The paper proposes a radical solution: concentrate all the rough and finish machining of the bolt holes and big/small end holes into a single operation, using a multi-station rotary table with multiple workpieces per station.
2. Process Layout and Machine Design
The machine design is the heart of this paper, and it is worth studying in detail. The layout is as follows:
| Station | Function | Workpieces per Station |
|---|---|---|
| 1 | Loading/unloading | 3 |
| 2 | Bolt hole rough and finish machining | 3 |
| 3 | Big/small end hole rough and finish machining | 3 |
| 4 | Bolt hole finish machining (secondary) | 3 |
| 5 | Big/small end hole finish machining (secondary) | 3 |
The rotary table has five stations, with three workpieces clamped at each station. The connecting rod is oriented with the rod cap facing outward, which allows access to the bolt holes from the outside. The table indexes 72 degrees per step, and the cycle time is determined by the longest operation at any station.
The key design decisions are:
- Process concentration: All operations are done in one clamping, eliminating the error from multiple setups.
- Multi-workpiece clamping: Three workpieces per station means the machine produces 15 parts per cycle, which gives the high throughput.
- Dedicated fixtures: Each station has a dedicated fixture with hydraulic clamping, ensuring consistent positioning.
- Dedicated spindle heads: The spindle heads are designed for the specific operations, with the correct speeds, feeds, and tooling.
3. Fixture and Spindle Head Design
The fixture design is critical. The connecting rod is a complex part, and it must be clamped rigidly without distortion. The paper describes a fixture that uses two locating pins and a flat surface, with hydraulic clamps applying force at the correct points. I would add one comment: the clamping force must be carefully controlled. Too much force will distort the part, and too little will allow it to move. The hydraulic system should have pressure regulators and gauges so the operator can verify the clamping force.
The spindle heads are also important. Each spindle head is a dedicated unit with its own motor, gearbox, and tooling. The bolt hole spindle heads use a two-step process: a roughing drill followed by a finishing reamer. The big/small end hole spindle heads use a similar approach, but with the addition of a boring operation for the final size. The spindle heads are mounted on the machine base, and the rotary table indexes them into position.
4. Production Results and Lessons Learned
The paper reports that the machine achieved a production capacity of about 1 million pieces per year, with a yield rate of 99.9% or better. The precision of the holes met or exceeded the technical requirements. These are excellent results, and they demonstrate the value of process concentration.
| Metric | Conventional Process | Special Machine |
|---|---|---|
| Annual capacity | 300–400 thousand pieces | 1 million pieces |
| Yield rate | 95–97% | 99.9%+ |
| Center distance accuracy | ±0.05 mm | ±0.02 mm |
| Number of setups | 3–4 | 1 |
| Cycle time per part | 2–3 minutes | 45–60 seconds |
The lessons are clear. Process concentration is not just about efficiency — it is about quality. When you eliminate multiple setups, you eliminate the error that comes from each setup. The connecting rod is a precision component, and the center distance between the big and small end holes is critical. By machining both holes in the same clamping, you ensure that the relationship between them is controlled by the machine tool geometry, not by the fixture accuracy.
One more lesson: the paper mentions that the machine was designed with a circular rotary table in the center of the bed. This is a good layout because it keeps the machine compact and allows the operator to access all stations from a single position. However, I would note that the loading station must be carefully designed to minimize operator fatigue. With three workpieces per station and a cycle time of about one minute, the operator will be loading and unloading parts continuously. The fixture should have easy access, and the clamping should be automated as much as possible.
5. Conclusion and Recommendations
This paper is an excellent example of how to solve a production problem through intelligent machine design. The special machine tool is a significant investment, but the return on investment is clear when you consider the increased capacity, improved yield, and reduced labor cost. My advice to engineers is to consider this approach for any high-volume precision component where the current process has multiple setups and low yield. The key is to analyze the process, identify the operations that can be combined, and design a machine that does them all in one clamping. The connecting rod is a perfect example, but the same principles apply to other components such as valve bodies, pump housings, and transmission parts. Process concentration is the future of precision manufacturing, and this paper shows how to do it right.
Zhuojin Pipe Fitting Co., Ltd