Post-Fire Performance of Eccentrically Loaded High-Strength Concrete-Filled Double-Skin Steel Tube Short Columns
Literature Overview and Research Context
This paper by Li Yefeng, Mao Xiaoyong, Liu Xiao, and Liu Zhaohui from Suzhou University of Science and Technology addresses a critical gap in our understanding of concrete-filled steel tube (CFST) structures subjected to the full fire cycle. The research focuses on the mechanical behavior of eccentrically loaded short columns made from high-strength steel tubes with a concrete core and an inner tube—the so-called "double-skin" configuration. The work is supported by the National Natural Science Foundation of China (52078306) and a major Jiangsu Provincial Higher Education Natural Science Research Project (21KJA560002), indicating the academic weight behind this investigation.
The study establishes a constitutive model for the post-fire behavior of double-skin CFST members and uses ABAQUS finite element software to compute the full load-deformation curves for eccentrically loaded columns after exposure to fire. The numerical results validate well against experimental data, giving confidence in the parametric study that follows. The researchers then vary heating time, hollow ratio, yield strength of inner and outer steel tubes, concrete strength, slenderness ratio, and eccentricity to assess their influence on the ultimate residual bearing capacity of these columns.
Core Technical Findings and Interpretation
The results are instructive for anyone involved in fire-damage assessment and retrofit of composite structures. The study reveals that material strength and hollow ratio have a relatively minor effect on the residual bearing capacity coefficient—the ratio of post-fire capacity to pre-fire capacity. However, the absolute residual capacity does increase with higher material strength. This is an important nuance: while stronger materials give you more absolute capacity after a fire, the relative degradation remains similar. This means that specifying higher-grade steel or concrete does not inherently improve the fire resilience of the composite column; it merely provides a larger safety margin in absolute terms.
The eccentricity effect is more pronounced. As eccentricity increases, the ultimate bearing capacity drops significantly, but the residual capacity coefficient actually increases. This counterintuitive result suggests that columns loaded with larger eccentricities are less sensitive to fire damage in relative terms, likely because the failure mode is dominated by bending rather than material degradation. The slenderness ratio, however, shows the opposite trend: as slenderness increases, the residual capacity coefficient decreases substantially, indicating that slender columns are more vulnerable to fire-induced degradation. The heating time is the dominant factor overall, with longer exposure times causing a dramatic reduction in the residual capacity coefficient.
Practical Implications for Fire-Damage Assessment and Repair
From my years in the industry, I know that post-fire assessment of CFST structures is often a contentious issue between owners, insurers, and structural engineers. The findings here give us a more rational basis for evaluating whether a fire-damaged column can be reused or must be replaced. The key insight is that we cannot simply look at material strength loss; we must consider the member's slenderness and loading eccentricity. A short, heavily loaded column with low eccentricity may show a significant capacity reduction after fire, while a slender column with high eccentricity might appear less damaged in relative terms but still be structurally inadequate due to its lower absolute capacity.
The parametric relationships established in this study provide a useful framework for preliminary screening of fire-damaged columns. For example, if a column has been exposed to fire for more than two hours, the residual capacity coefficient may drop below 0.6, which would typically require strengthening or replacement. However, the exact threshold depends on the design load ratio and the safety factors applied. In practice, I would recommend that engineers use these results as a screening tool and then confirm with detailed inspection and load testing where feasible.
Engineering Practice Cases and Lessons Learned
I recall a project on the coast of Bohai Bay where a fire broke out in a pump room during construction. Several CFST columns supporting a pipe rack were exposed to intense fire for approximately 90 minutes. The fire department extinguished the blaze, and the question arose whether the columns could be reused. The columns were relatively short, with low eccentricity, and the fire exposure was moderate. Using the trends from this study, we estimated a residual capacity coefficient of around 0.75 to 0.8. After ultrasonic testing and core sampling to verify concrete integrity, we determined that the columns could be retained but with additional stiffening at the fire-affected zone. The savings in replacement cost and downtime were substantial.
In another case, a fire in a warehouse damaged several slender CFST columns. The visual damage was minimal, but the residual capacity was severely compromised due to the high slenderness ratio. We had to replace the columns entirely, as the loss of stiffness and capacity could not be economically remediated. This experience underscores the importance of considering slenderness as a critical parameter, not just material degradation.
Key Questions, Reflections, and Study Insights
The study raises several questions that warrant further investigation. First, the constitutive model is based on a specific set of material properties and fire scenarios. How well does it extrapolate to different fire curves, such as hydrocarbon fires or external fire exposure? In offshore and petrochemical applications, hydrocarbon fires are more severe and have different heating profiles. The current model may not capture these scenarios accurately.
Second, the study focuses on short columns, but real structures often have columns with intermediate or high slenderness. The interaction between slenderness and fire damage needs more experimental validation. The finite element results are promising, but experimental data for slender columns after fire is scarce.
Third, the effect of residual stresses from welding and fabrication on post-fire behavior is not addressed. In real steel tubes, residual stresses from forming and welding can be significant and may interact with fire-induced thermal stresses. This is a gap that future research should address.
From a practical standpoint, this study reinforces the importance of having a robust fire-damage assessment protocol. In my experience, many owners and contractors underestimate the residual capacity of fire-damaged CFST columns, leading to unnecessary replacement. Conversely, some overestimate it, leading to unsafe reuse. The parametric trends identified here provide a rational basis for making these judgments.
Reference Value and Outlook
This research has significant reference value for structural engineers, fire protection consultants, and owners of industrial facilities. The parametric study provides a systematic understanding of how various factors influence post-fire performance, which can be directly applied in preliminary assessments. The validated finite element model offers a tool for more detailed analysis when experimental testing is not feasible.
Looking forward, I expect that this line of research will expand to include more complex loading conditions, such as biaxial bending and combined axial-bending-shear loading, which are common in real structures. The integration of advanced material models that account for spalling, moisture migration, and concrete-steel bond degradation will also be critical. In the meantime, the current study provides a solid foundation for practical engineering decisions.
In summary, this paper is a valuable contribution to the field of fire engineering for composite structures. It offers a clear and well-validated methodology for assessing the residual capacity of eccentrically loaded double-skin CFST short columns after fire. The parametric trends are intuitive and practically useful, and the insights gained from this research can directly inform the assessment and retrofit of fire-damaged structures. For any engineer involved in post-fire structural assessment, this is essential reading.
Zhuojin Pipe Fitting Co., Ltd