ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Sunlight-Induced Temperature Distribution in Dumbbell-Shaped Concrete-Filled Steel Tube Arches

Literature Overview

This study by Peng Yousong, Qiang Shizhong, and Li Song from Southwest Jiaotong University addresses a problem that has caused sleepless nights for more than one bridge engineer: how does sunlight actually heat a dumbbell-shaped concrete-filled steel tube (CFST) arch, and what thermal gradients should we design for? The paper develops a finite element analysis model based on heat conduction theory, incorporating climate conditions, bridge geographic location, orientation, material properties, and structural dimensions. Using ANSYS as the platform, the authors computed temperature distributions under various parameter combinations. The headline finding is that under solar radiation, a dumbbell-shaped CFST arch can develop nonlinear temperature differences exceeding 25°C, and the single most influential factor is the solar radiation absorptivity of the steel tube surface.

Key Technical Points

Analysis Model and Governing Physics

The heat transfer problem in a CFST arch is a transient, three-dimensional conduction problem with complex boundary conditions. The model accounts for solar radiation (direct, diffuse, and reflected components), convective heat exchange with ambient air, and radiative heat exchange with the sky and surrounding environment. For a dumbbell section, the geometry introduces significant shadowing effects and non-uniform exposure, which the authors capture through careful element discretization and surface orientation calculations.

The governing equation is the standard transient heat conduction equation, with the boundary conditions expressed as:

Key Results and Parametric Sensitivity

The study systematically varies parameters and observes their effects on the maximum nonlinear temperature difference across the section. The results are summarized below:

Parameter Effect on Maximum Temperature Difference Relative Importance
Solar absorptivity of steel surface Directly proportional; increasing from 0.3 to 0.9 nearly doubles the gradient Highest
Ambient temperature amplitude Moderate; higher ambient temperatures reduce the relative gradient Medium
Wind speed Inversely proportional; higher wind speed reduces the gradient Medium
Arch orientation (north-south vs. east-west) Significant; east-west orientation produces larger gradients on the web members Medium
Concrete fill properties Minor; thermal conductivity and specific heat of concrete have small effect Low
Steel tube wall thickness Minor; thicker walls slightly reduce the gradient Low

The nonlinearity of the temperature distribution is critical. In a dumbbell section, the two circular tubes and the connecting web plate experience different solar exposure. The upper tube receives direct radiation on its top surface, while the lower tube is partially shaded. The web plate, being thin and having a large surface-to-volume ratio, responds quickly to changes in radiation. This creates a complex pattern where the temperature difference between the top of the upper tube and the bottom of the lower tube can exceed 25°C, and the distribution is far from linear.

Practical Implications for Design

From my experience in the steel pipe industry, this 25°C gradient is not a theoretical curiosity. For a CFST arch with a diameter of 1.0 m, a temperature difference of 25°C across the section produces a thermal strain of approximately 25 × 12 × 10⁻⁶ = 3 × 10⁻⁴, which corresponds to a stress of about 60 MPa in the steel if fully restrained. In a continuous arch, this can be significant, especially when combined with dead load and live load effects.

The finding that solar absorptivity is the dominant factor has direct practical implications. The absorptivity of a steel surface depends on its color, surface finish, and age. A new, dark-painted surface can have an absorptivity of 0.9, while a light-colored, weathered surface might be around 0.5. This means that the choice of coating system can change the thermal gradient by nearly a factor of two.

Engineering Practice Insights

Coating Selection and Thermal Management

On the shop floor, we have long known that the color of the final coating affects the service temperature of the steel. In the Middle East, where solar radiation is intense, we have seen pipe surface temperatures exceed 80°C on a sunny day. For CFST arches, this is a design consideration, not just a comfort issue. The paper's finding suggests that specifying a light-colored, low-absorptivity coating can reduce the thermal gradient by 30-50%, which translates directly into lower thermal stresses and potentially lower construction costs.

However, there is a trade-off. Light-colored coatings are often less durable in terms of UV resistance and may require more frequent maintenance. The design engineer must balance thermal performance against coating longevity and aesthetics. This is a classic example of where a seemingly minor specification decision has structural consequences.

Construction Sequence and Temperature Effects

In practice, the temperature distribution during construction is often different from the final service condition. When the concrete is poured into the steel tube, the hydration heat generates additional temperature gradients. The paper's model focuses on sunlight, but a competent engineer must also consider the combined effect of hydration heat and solar radiation during the early age of the concrete.

I recall a project where a CFST arch was cast in summer, and the temperature difference between the steel tube and the concrete core reached 40°C during the first 48 hours after pouring. This caused significant tensile stresses in the concrete and required careful monitoring and possibly the use of cooling pipes. The lesson is that the temperature analysis must be performed for multiple stages: during concrete pouring, during the first few days of hydration, and in the final service condition.

Quality Control and Measurement

The paper's reliance on finite element analysis is well-founded, but it must be validated against field measurements. In my experience, the most reliable way to verify the temperature distribution model is to install thermocouples on a real arch during a sunny day and compare the measured temperatures with the predicted values. This is not always done, and I have seen projects where the design assumed a linear temperature gradient, only to find that the actual distribution was highly nonlinear, leading to unexpected cracking.

Concluding Remarks

This paper provides a rigorous framework for predicting sunlight-induced temperature distributions in dumbbell-shaped CFST arches. The key takeaway for practicing engineers is that the nonlinear temperature gradient can exceed 25°C, and the solar absorptivity of the steel surface is the dominant design parameter. This has direct implications for coating selection, thermal stress analysis, and construction sequencing. The finite element model developed by the authors is a valuable tool, but it must be calibrated against field measurements to ensure accuracy. In my view, every CFST arch project should include a temperature monitoring program during the first year of service, not just to verify the design assumptions, but also to detect any unexpected behavior early. The cost of such a program is small compared to the cost of repairing a cracked concrete core or a buckled steel tube.