Longitudinal Allowable Stress in Steel Tubes of Concrete-Filled Steel Tube Columns
The Stress State Problem
The paper by Liu Yongjian, Jiang Lei and Zhang Ning addresses a fundamental issue in the design of concrete-filled steel tube (CFST) columns: what is the actual stress state of the steel tube at ultimate load? In a CFST column under axial compression, the steel tube and the concrete core work together. The concrete is confined by the steel tube, which increases its compressive strength. The steel tube is subjected to a biaxial stress state: longitudinal compression from the axial load and hoop tension from the confinement of the concrete. This biaxial stress state reduces the longitudinal load-carrying capacity of the steel tube.
The authors introduce two coefficients: a longitudinal allowable stress reduction factor for the steel tube, and a concrete compressive strength increase factor. These coefficients account for the interaction between the steel and the concrete. The paper provides a theoretical analysis of the stress state, calculates the coefficients, and compares the calculated values with experimental data.
Theoretical Model and Coefficient Calculation
The authors' approach is to consider the steel tube in a multiaxial stress state at the ultimate load. The longitudinal stress in the steel tube is reduced by the hoop stress, according to a yield criterion. The concrete core, on the other hand, is subjected to triaxial compression, which increases its strength. The authors derive expressions for the reduction factor and the increase factor, and they show that the calculated values agree well with experimental results.
| Parameter | Symbol | Typical Value Range | Practical Significance |
|---|---|---|---|
| Steel tube longitudinal stress reduction factor | k | 0.7–0.9 | Reduces the allowable axial stress in the steel tube |
| Concrete compressive strength increase factor | β | 1.2–1.5 | Increases the allowable compressive stress in the concrete |
| Steel tube diameter-to-thickness ratio | D/t | 20–100 | Higher D/t reduces confinement effectiveness |
| Concrete strength grade | C30–C80 | 30–80 MPa | Higher strength concrete reduces the benefit of confinement |
The key insight is that the steel tube in a CFST column is not simply carrying axial load. It is also carrying hoop tension, which reduces its capacity to carry axial load. The reduction factor accounts for this. The concrete, on the other hand, benefits from the confinement provided by the steel tube, and the increase factor accounts for this benefit.
Comparison with Test Data and Code Implications
The authors compared their calculated values with experimental results, and the agreement was good. This is the critical validation step. A theoretical model that does not agree with experiments is of no use to a design engineer. The fact that the calculated values match the test data means that the model can be used with confidence.
| Comparison | Calculated Value | Experimental Value | Deviation |
|---|---|---|---|
| Ultimate axial load | Within 10% of experimental | Reference | Acceptable for design |
| Steel tube stress reduction | Consistent with observed behavior | Reference | Validates the coefficient |
| Concrete strength increase | Consistent with observed behavior | Reference | Validates the coefficient |
The practical implication is that designers can use these coefficients to calculate the ultimate capacity of CFST columns more accurately. This is particularly important for bridge design, where CFST columns are used extensively. The authors' work provides a more rational basis for design than the traditional approach, which often ignores the biaxial stress state in the steel tube.
Practical Engineering Judgment
From my perspective, this paper addresses a real problem that I have seen in the design and construction of steel-concrete composite structures. The interaction between the steel tube and the concrete core is complex, and it is tempting to simplify it. The authors' approach of introducing two coefficients is a good compromise between accuracy and simplicity.
A key lesson is about the importance of understanding the stress state in the steel tube. In a CFST column, the steel tube is not simply a column; it is also a confinement vessel. The hoop stress from the concrete confinement reduces the longitudinal capacity of the steel. This is a subtle but important effect that is often overlooked.
A second lesson is about the validation of the model. The authors compared their calculations with experimental data, and the agreement was good. This is the standard that any design model must meet. In my experience, the best design models are those that have been validated against a wide range of experimental data.
A third lesson is about the practical application of the coefficients. The reduction factor and the increase factor are simple to use in design calculations. They can be incorporated into existing design methods without major changes. This makes the work immediately useful to design engineers.
In conclusion, this paper provides a rigorous and validated method for calculating the ultimate capacity of CFST columns. The introduction of the longitudinal allowable stress reduction factor and the concrete compressive strength increase factor is a significant contribution. The good agreement between calculated and experimental values gives confidence in the method. For those of us who design and build steel-concrete composite structures, this is a valuable reference that should be incorporated into design practice.
Zhuojin Pipe Fitting Co., Ltd