ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Axial Compressive Performance of Recycled Aggregate Concrete-Filled Thin-Walled Steel Tube Short Columns

Literature Overview and Core Findings

This study by Zhi Zhengdong and colleagues at Yancheng Institute of Technology and Nanjing Tech University presents a focused experimental program on recycled aggregate concrete-filled steel tube (RACFST) short columns. The work is timely because the construction industry faces increasing pressure to incorporate recycled materials while maintaining structural performance. The authors tested six RACFST short columns and three conventional concrete-filled steel tube (CFST) short columns under axial compression, varying the recycled aggregate replacement ratio and the length-to-diameter ratio.

The key findings are straightforward and practically useful. First, the failure modes of RACFST short columns are similar to conventional CFST columns, which means the fundamental load-transfer mechanism—concrete confined by the steel tube—remains intact even with recycled aggregate. Second, as the recycled aggregate replacement ratio increases, the ultimate bearing capacity decreases. Third, as the length-to-diameter ratio increases, the capacity also decreases. Finally, the existing calculation method for conventional CFST columns can be applied to RACFST columns with acceptable accuracy.

Technical Parameter Analysis and Practical Implications

Parameter Range Tested Observed Effect on Capacity
Recycled aggregate replacement ratio 0%, 50%, 100% Capacity decreases with increasing replacement ratio
Length-to-diameter ratio (L/D) Varied across specimens Capacity decreases with increasing L/D
Steel tube type Thin-walled Confinement effectiveness reduced compared to thick-walled
Failure mode Local buckling, concrete crushing Similar to conventional CFST

From a manufacturing perspective, the thin-walled steel tube is the critical component. In my experience producing thin-walled tubes for structural applications, the wall thickness tolerance and the initial geometric imperfections have a disproportionate effect on the confinement efficiency. If the tube wall is too thin relative to the diameter, the tube cannot develop sufficient hoop stress to confine the concrete core effectively, and local buckling becomes the governing failure mode. The study's finding that capacity decreases with recycled aggregate replacement is consistent with the lower elastic modulus and higher shrinkage of recycled concrete, which reduces the composite action.

Engineering Practice and Delivery Considerations

In real construction, the practical challenge with RACFST columns is not just the structural performance but the filling process itself. When we supply steel tubes for concrete-filled applications, the client must ensure proper concrete placement. For thin-walled tubes, the risk of tube rupture during concrete pumping is real. I have seen projects where the concrete was pumped at excessive pressure, causing the tube to bulge or even burst at the weld seam.

The weld quality of the longitudinal seam is paramount. For thin-walled tubes, a lack of fusion or an undercut in the longitudinal weld can become a stress concentration point that initiates local buckling at a load far below the theoretical capacity. The standard practice should be to require full penetration welds and to perform 100% ultrasonic testing on the longitudinal seam for any tube intended for concrete filling.

The study's conclusion that existing CFST calculation methods apply to RACFST is reassuring but should be treated with caution. The margin of error may be acceptable for design purposes, but the actual safety factor should be increased when recycled aggregate is used, particularly for high replacement ratios. In my experience, the reduction in capacity with recycled aggregate is not linear, and the variability increases significantly. A conservative approach would be to limit the recycled aggregate replacement to 50% for structural applications unless full-scale verification tests are performed.

Study Insights and Reflections

This study provides a useful baseline for engineers considering recycled aggregate in CFST columns. The key takeaway is that the technology is viable, but the design must account for the reduced capacity and increased variability. The thin-walled tube aspect is particularly relevant because it amplifies the effects of concrete quality. A thicker tube provides more confinement and can compensate for the lower stiffness of recycled concrete.

The study is limited by the small number of specimens and the lack of long-term behavior data. In practice, the shrinkage and creep of recycled concrete over time will affect the composite action. The steel tube carries a higher proportion of the load as the concrete shrinks, which can lead to premature yielding of the tube. This is a critical consideration for structures with long service lives.

From a delivery perspective, the marking and documentation for RACFST columns must clearly identify the concrete type and the recycled aggregate ratio. If the wrong concrete is placed, the structural performance may be compromised without any visible indication. The quality control plan should include verification of the concrete mix design at the batching plant and at the point of placement.