ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Ceramic Lined Steel Pipe: SHS-Centrifugal Process and Performance

Overview

The paper by Yin Sheng et al. on ceramic lined steel pipe prepared by self-propagating high-temperature synthesis (SHS) combined with centrifugal casting is a classic in the field. It addresses a persistent problem in the process industries: the wear and corrosion of steel pipes handling abrasive slurries, molten metals, or corrosive fluids. The SHS-centrifugal method produces a composite pipe with a dense ceramic inner layer and a steel outer shell, offering a combination of toughness from the steel and hardness from the ceramic. This is a technology that has found its way into power plant ash handling, mining slurry transport, and even some chemical plant applications.

Process and Mechanism

The SHS reaction involves the reduction of iron oxide by aluminum, typically using a mixture of Fe₂O₃ and Al powders. The reaction is highly exothermic, generating temperatures above 2000°C. When performed in a rotating steel pipe, the centrifugal force separates the molten products: the denser iron settles to the outer surface, forming a metallic bond with the steel pipe, while the lighter alumina (Al₂O₃) forms the inner ceramic layer. The centrifugal force also helps to consolidate the ceramic and expel gas bubbles.

Process Parameter Typical Value / Range Effect
Fe₂O₃:Al ratio 1:1 to 1:1.2 (molar) Controls reaction temperature and product composition
Centrifugal acceleration 50–200 g Determines layer separation and density
Pipe rotation speed 800–3000 rpm Depends on pipe diameter
Ignition method Chemical or electrical Initiates the SHS wave
Cooling rate Controlled Affects residual stress and ceramic microstructure

The paper emphasizes that the centrifugal force has a major influence on the combustion process and the phase separation. Too low a force leaves a porous ceramic layer; too high a force can cause the iron to penetrate the ceramic, reducing its hardness. The optimum is a balance that yields a dense, uniform alumina layer.

Properties and Residual Stress

The composite pipe exhibits a beneficial residual stress distribution: the ceramic layer is in compression and the steel tube is in tension. This is because the ceramic has a lower coefficient of thermal expansion than the steel, so upon cooling from the SHS temperature, the ceramic contracts less, putting it into compression. This residual stress state is critical for the mechanical and thermal shock resistance of the composite. The compressive stress in the ceramic prevents crack initiation and propagation, while the tensile stress in the steel is well within its elastic range.

Property Ceramic Lined Steel Pipe Plain Steel Pipe
Hardness (ceramic layer) 1200–1600 HV 150–250 HV
Wear resistance (relative) 5–10 times steel 1
Corrosion resistance Excellent in acidic/alkaline media Poor in many media
Maximum service temperature 800–1000°C (ceramic limit) 400–500°C (steel limit)
Thermal shock resistance Good (due to compressive residual stress) Moderate

The paper reports good mechanical properties, including a strong bond between the ceramic and the steel. In practice, the bond strength is often tested by a shear test or by thermal cycling. The composite pipe can withstand significant mechanical impact because the steel shell absorbs the energy, and the ceramic layer, being in compression, resists cracking.

Manufacturing and Quality Control

From a manufacturing standpoint, the SHS-centrifugal process is relatively simple and economical for producing short to medium length pipes (up to a few meters). The key quality control points are:

  1. Raw material purity and particle size: the Fe₂O₃ and Al powders must be dry and well mixed to ensure a uniform reaction.
  2. Pipe preparation: the inner surface must be clean and roughened to promote bonding; any oil or scale will cause delamination.
  3. Rotation speed and time: must be precisely controlled to achieve the desired centrifugal force and layer thickness.
  4. Cooling rate: slow cooling is preferred to reduce thermal gradients and minimize the risk of ceramic cracking.
  5. Non-destructive testing: ultrasonic or radiographic inspection can detect voids or delamination in the ceramic layer.

In my experience, the most common defect is a porous ceramic layer caused by insufficient centrifugal force or gas entrapment. This leads to premature wear and spalling. The remedy is to increase the rotation speed or add a small amount of a deoxidizer to the mix.

Application and Lessons

Ceramic lined steel pipes are widely used in power plants for bottom ash and fly ash transport, in mining for ore slurry lines, and in steel plants for slag handling. The main limitation is the pipe length: SHS is a batch process, and the pipe must be rotated as a whole. For longer runs, sections are joined by flanging or welding, but welding the composite pipe requires special procedures to avoid damaging the ceramic layer. A common approach is to weld a steel collar onto the outer shell and then bolt the flanges, leaving the ceramic joint protected by a gasket.

One lesson I have learned is that the ceramic layer is brittle, so the pipe must not be subjected to bending or impact during handling and installation. Even a small drop can cause a crack that will propagate under thermal cycling. The pipe should be supported at close intervals and never used as a structural member.

Conclusions

The SHS-centrifugal ceramic lined steel pipe is a proven solution for severe wear and corrosion applications. The residual stress distribution, with the ceramic in compression, gives it excellent resistance to mechanical and thermal shock. The process is cost-effective for many applications, but the quality of the ceramic layer depends heavily on the process parameters and raw materials. As an engineer, I would specify this pipe for slurry transport where the slurry is abrasive and the temperature is moderate, but I would always require a full inspection of the ceramic layer and a careful handling procedure. The technology has matured, but the manufacturing discipline must remain high to avoid the pitfalls of porosity and delamination.