Energy Absorption Characteristics of Steel Pipes Under Lateral Explosion Shock Wave Loading
Why This Paper Still Matters to a Pipe Man
I have spent thirty years in this industry, and I can tell you that most of the literature on steel pipe is written for the shop floor or the pipeline corridor. This 2002 paper from the PLA University of Science and Technology is different. It sits squarely in the world of protective engineering, where a steel pipe is not a conduit for oil or gas but a sacrificial energy absorber that has to eat a blast and keep the people behind it alive. The authors, Tang Degao, Zhou Bukui and Zhou Zaosheng, ran experiments on horizontally laid single and double steel pipes under lateral explosion shock wave loading, and their conclusions have direct relevance to anyone who designs blast barriers, crash cushions, or protective structures around critical infrastructure.
Core Findings and Technical Interpretation
The paper identifies three dominant factors that control how much energy a steel pipe can absorb before it collapses: geometric dimensions, the mass of the energy-absorbing component (including any attached counterweight or filler), and the structural form, i.e., whether you use a single pipe or a nested double-pipe configuration. These sound obvious, but the experimental data behind them is what makes the paper worth reading.
Geometric Scale Effects
The energy absorption capacity scales nonlinearly with pipe diameter and wall thickness. A larger diameter gives you a longer plastic hinge travel before the pipe walls touch, which means more plastic work is done. Wall thickness matters even more because it directly controls the plastic moment capacity of the cross-section. In my experience with crash barriers and ship collision protection, the ratio of diameter to wall thickness (D/t) is the single most important parameter. If you go below D/t of about 20, the pipe tends to fail by local buckling at the load point rather than by stable plastic folding, and you lose a large portion of the theoretical energy absorption. If you go above D/t of about 60, the pipe becomes a thin shell that crumples too early and absorbs very little. The sweet spot for blast energy absorbers is usually D/t between 25 and 45.
The Role of Counterweight Mass
The paper highlights the mass of the energy-absorbing element as a key variable. This is counterintuitive to many engineers who think a lighter structure is always better. In a blast scenario, the mass of the pipe and any attached components affects the inertia of the system, which in turn determines how quickly the pipe deforms and how much of the impulse is converted into plastic work rather than rigid-body motion. If the pipe is too light, it accelerates away from the blast wave and absorbs little energy. If it is too heavy, it may not deform at all and simply transfers the load to the supporting structure. There is an optimal mass for a given blast impulse, and the paper's experiments quantify this for the specific geometries tested.
Single Versus Double Pipe Configuration
The double-pipe configuration, where a smaller pipe is nested inside a larger one with a gap or filler between them, is a classic energy absorber design. The outer pipe deforms first, then the inner pipe begins to deform as the gap closes. This staged deformation gives you a longer effective stroke and a more stable force-displacement curve than a single pipe of equivalent mass. The paper confirms this experimentally. What the paper does not fully explore is the effect of the filler material in the annulus. In my experience, filling the gap with concrete, sand, or a crushable foam changes the deformation mode dramatically. A concrete-filled double pipe will absorb significantly more energy but at a much higher peak force, which may not be acceptable if the supporting structure is not designed for it. A foam-filled annulus gives a more gradual force rise and is often the better choice for protecting personnel rather than equipment.
Engineering Practice and Lessons Learned
I have seen this principle applied in the field in several contexts. The most common is the use of steel pipe arrays as vehicle crash barriers at plant entrances and around offshore platform boat landings. The design philosophy is the same as the paper's experiments: the pipes are sacrificial, they are meant to deform plastically and absorb the kinetic energy of an impact, and the supporting structure behind them is designed to remain elastic. What the paper reminds us is that the arrangement matters. A single row of large-diameter pipes is not as effective as two rows of smaller pipes with staggered spacing, because the staggered arrangement distributes the load over a longer time and prevents the blast or impact from punching through at a single point.
In my experience with pipeline protection against third-party interference, we have used steel pipe sleeves over buried pipelines in areas where excavation equipment or vehicle impacts are a risk. The sleeve is essentially an energy absorber. The key lesson from this paper is that the sleeve must be sized so that it deforms plastically before it transmits a damaging load to the carrier pipe. If the sleeve is too stiff, it does not absorb energy; if it is too thin, it collapses and the carrier pipe takes the full load.
Critical Reflection and Practical Judgement
This paper was published in 2002, and the experimental methods are relatively straightforward. What it does not address is the effect of strain rate on the mechanical properties of the steel. Under explosive loading, strain rates can reach 10 to 1000 per second, and the yield strength of carbon steel can increase by 20 to 50 percent due to strain rate sensitivity. The paper's static material properties may therefore underestimate the energy absorption capacity of the pipes in a real blast event. This is a conservative error, which is acceptable for design, but it means the paper's quantitative results should not be used directly for design without applying a strain rate correction factor.
Another point that the paper does not cover is the effect of end conditions. A pipe that is simply supported at both ends will absorb less energy than a pipe that is fixed at both ends, because the fixed ends allow plastic hinges to form at the supports as well as at the load point. In my experience with barrier design, the end connections are often the weakest link. If the pipe is welded to a rigid frame, the weld may fail before the pipe has a chance to deform plastically. The paper's experiments appear to have used relatively simple support conditions, and this is a limitation that should be noted.
Study Insights and Implications for Practice
The practical takeaway for the working engineer is straightforward. When you are designing a steel pipe energy absorber, do not focus on material strength alone. The geometry, the mass distribution, and the structural configuration are what determine performance. A lower-strength steel with a well-chosen D/t ratio and a double-pipe configuration will outperform a high-strength steel with a poor geometry. This is a lesson I have learned the hard way, having seen a high-strength steel barrier crack at the welds before it could absorb any significant energy, while a mild steel barrier of the same weight deformed beautifully and stopped the vehicle.
For the procurement side, this paper reinforces the importance of specifying the right steel grade and the right dimensional tolerances. If the wall thickness tolerance is too loose, the actual D/t ratio may fall outside the intended design window, and the energy absorption capacity may be significantly lower than calculated. I have rejected pipe shipments for energy absorber applications where the wall thickness was 10 percent under nominal, because that 10 percent can translate into a 20 to 30 percent reduction in energy absorption capacity.
Conclusion and Reference Value
This paper is a useful reminder that steel pipe is a versatile engineering material, and its application in protective structures is a legitimate and growing field. The experimental data on single versus double pipe configurations and the influence of geometric scale and mass are valuable design inputs. The paper's limitation in not addressing strain rate effects and end conditions means that a careful designer should supplement it with dynamic testing or finite element analysis for critical applications. For the industry veteran, the real value of this paper lies in its confirmation that the simple, practical variables, geometry, mass, and configuration, are the ones that dominate performance, and that over-specifying material strength is often a waste of money.
Zhuojin Pipe Fitting Co., Ltd