ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Mechanical Behavior of Concrete-Filled Steel Tube Structures During Construction

Introduction and Literature Context

The paper by Wang Wenda and Han Linhai from Fuzhou University, published in Industrial Construction in 2004, examines the mechanical behavior of concrete-filled steel tube (CFST) structures during the construction phase. This is a topic that is often overlooked in the design of CFST structures, as the focus is typically on the final service condition. However, the authors make a compelling case that the construction phase is critical because the empty steel tube must act as a vertical support skeleton to carry construction loads before the concrete is poured. Additionally, the steel tube acts as formwork and must resist the hydrostatic pressure of the wet concrete. The paper discusses the necessity of a two-stage design approach and uses finite element analysis to study the mechanical behavior of CFST columns during construction.

Key Technical Findings and Interpretation

The paper identifies two critical loading conditions during construction. First, the empty steel tube must carry vertical construction loads, which include the weight of the tube itself, the weight of any equipment, and the loads from the floors above. This creates initial stresses in the steel tube that are not present in the final service condition. Second, when the concrete is poured, the steel tube acts as formwork and must resist the lateral hydrostatic pressure of the wet concrete. This pressure can be significant, especially for large-diameter tubes, and it can cause the tube to bulge or even buckle if the wall thickness is insufficient.

The authors propose a two-stage design approach, where the first stage considers the empty tube under construction loads, and the second stage considers the composite section under service loads. This is a sound engineering approach that acknowledges the reality that the steel tube must be designed to act alone before the concrete is placed. The finite element analysis is used to study the stress distribution in the tube during construction, and the results show that the initial stresses can be significant, particularly in the lower columns of a tall building. These initial stresses can affect the performance of the final composite structure, as they reduce the capacity of the steel tube to resist service loads.

Practical Implications for Steel Pipe Fabrication and Construction

From a practical standpoint, this paper highlights the importance of considering the construction sequence in the design of CFST structures. In my experience, the construction phase is often the most dangerous period for a structure, as it is when the loads are not fully understood and the structure is not yet complete. The empty steel tube is particularly vulnerable because it has no concrete to provide lateral support and to share the load. This means that the tube must be designed to resist buckling under the vertical construction loads and to resist bulging under the hydrostatic pressure of the wet concrete.

For the steel pipe manufacturer, this means that the wall thickness of the tube must be sufficient to resist these construction loads. In many cases, the wall thickness is governed by the construction condition rather than the service condition. This is a critical design consideration that is often missed. I have seen cases where a tube was designed based on the service condition, but it buckled during construction because the construction loads were not considered. This is a serious failure that can lead to structural collapse and loss of life.

The hydrostatic pressure of the wet concrete is another critical consideration. For large-diameter tubes, the pressure can be substantial, and the tube must have sufficient stiffness to resist bulging. This is particularly important for tubes that are not fully supported during the concrete pour. In practice, this means that the tube may need to be reinforced with temporary stiffeners or that the concrete must be poured in stages to limit the hydrostatic pressure. These are practical details that are often overlooked in the design phase but have a significant impact on the safety of the construction process.

Standards and Quality Control Considerations

The design of CFST structures during construction is not explicitly covered by most standards. In China, GB 50936 provides the general framework for CFST structures, but it focuses on the service condition. The construction phase is typically addressed through a separate construction plan, which must be prepared by the contractor and approved by the designer. This plan must consider the loads that will be applied to the structure at each stage of construction and must ensure that the structure has sufficient capacity to resist those loads.

For the steel pipe manufacturer, the key quality control points are the dimensional accuracy of the tube, the quality of the weld, and the mechanical properties of the steel. The tube must be manufactured to a tolerance that ensures it can be erected accurately and that it will behave as assumed in the design. The weld quality is critical, as any defect could lead to a crack that propagates under the construction loads. In my experience, the most common defect in CFST tubes is a lack of fusion in the longitudinal weld, which can be difficult to detect with ultrasonic testing if the defect is oriented in a certain way. This is why it is essential to use a combination of nondestructive testing methods, including ultrasonic testing and radiography, to ensure the weld quality.

Study Insights and Reflections

This paper is a valuable reminder that the construction phase is a critical design condition that must not be ignored. The authors' proposal for a two-stage design approach is sound and should be adopted by all engineers involved in CFST structures. In my experience, the construction phase is often the most dangerous period for a structure, and it is essential to have a clear understanding of the loads that will be applied at each stage.

The finite element analysis is a powerful tool for studying the behavior of the structure during construction, but it must be used with care. The results of the analysis are only as good as the input parameters, which include the material properties, the boundary conditions, and the loading sequence. In my experience, the loading sequence is often the most difficult to model accurately, as it depends on the construction method and the sequence of concrete pours. This paper provides a good framework for approaching this problem, but it is important to remember that each project is unique and must be analyzed on its own merits.

Conclusion

The study by Wang Wenda and Han Linhai provides a thorough analysis of the mechanical behavior of CFST structures during construction. The key contributions are the identification of the two critical loading conditions, the proposal of a two-stage design approach, and the finite element analysis of the stress distribution in the tube during construction. For steel pipe manufacturers, this paper underscores the importance of considering the construction condition in the design of the tube, as the wall thickness may be governed by the construction loads rather than the service loads. The hydrostatic pressure of the wet concrete is a critical consideration for large-diameter tubes, and the tube must have sufficient stiffness to resist bulging. This paper is a valuable reference for engineers involved in the design and construction of CFST structures, and it highlights the need for a comprehensive understanding of the entire life cycle of the structure, from fabrication to service.