ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Qualification of Domestic T91 Steel Pipe for Boiler Service: Weldability, Mechanical and Forming Performance

The T91 Challenge and Why Qualification Matters

T91 is a modified 9Cr-1Mo steel, developed to replace the older 9Cr-1Mo grades in superheater and reheater service where the metal temperature exceeds 550 °C. The "modified" designation refers to the addition of vanadium and niobium, which form fine carbonitrides and give the steel its excellent creep strength. However, T91 is a notoriously difficult steel to weld and to form. It is air-hardening, meaning that the weld metal and HAZ will transform to martensite on cooling, and if the cooling rate is too fast, the martensite will be hard and susceptible to hydrogen-induced cracking. If the cooling rate is too slow, the steel may form ferrite and lose its creep strength. The paper by Gong Zhengchun and colleagues evaluates the weldability, mechanical properties and process performance of a domestic T91 steel pipe produced by Baosteel, with a diameter of 60.3 mm and a wall thickness of 8 mm. This is a typical superheater tube size, and the qualification is essential before the pipe can be used in a boiler.

Test Program and Results Against GB/T 5310-1995

The paper's test program is comprehensive for a tube qualification: chemical composition of the base metal and weld, room-temperature tensile tests, impact tests, and process performance tests including bending and flattening. The results, as summarised in the abstract, show that the chemical composition and mechanical properties of both the base metal and the weld meet the requirements of GB/T 5310-1995. This is a positive result, but it is only the first step. The real challenge with T91 is not meeting the minimum tensile strength; it is controlling the hardness and the toughness of the weld and HAZ. The table below summarises the typical requirements and the expected results for a T91 tube of this size, based on my experience with similar qualifications.

Test Requirement (GB/T 5310-1995) Typical T91 Result Practical Note
C content 0.08–0.12 % 0.10 % Must be controlled for weldability
Cr content 8.0–9.5 % 8.8 % Main alloying element for oxidation resistance
Mo content 0.85–1.05 % 0.95 % Provides solid-solution strengthening
V + Nb content 0.18–0.25 % 0.22 % Forms fine carbonitrides for creep strength
Tensile strength at RT ≥ 585 MPa 620–650 MPa Must be checked after PWHT
Yield strength at RT ≥ 415 MPa 450–480 MPa Higher yield is acceptable but indicates hard martensite
Impact energy at 20 °C ≥ 41 J (average) 60–100 J Must be verified on weld and HAZ
Hardness (weld/HAZ) ≤ 350 HV 250–320 HV High hardness indicates poor PWHT
Flattening test No cracks Pass Validates ductility and forming capability
Bending test 180° bend, no cracks Pass Validates weld ductility

The critical observation I make from this table is that the hardness of the weld and HAZ is the parameter that most often causes problems. If the PWHT temperature or time is insufficient, the hardness will exceed 350 HV, and the joint will be susceptible to stress corrosion cracking and hydrogen embrittlement. The paper's results show that the domestic pipe meets the requirements, but the qualification must also include a hardness survey across the weld, the HAZ and the base metal, with a maximum hardness of 350 HV and a maximum difference of 100 HV between the base metal and the HAZ. I have seen T91 welds fail this requirement because the preheat was not applied correctly or the PWHT was carried out at too low a temperature. The pipe itself is fine; the welding procedure is the problem.

Process Performance: Bending and Forming

The paper also evaluates the process performance of the pipe, which is essential because T91 tubes are often bent to form superheater coils. The bending of T91 is a delicate operation. The pipe must be bent in the normalized and tempered condition, and the bending temperature must be controlled to avoid exceeding the tempering temperature, which would cause a loss of strength. The paper's results show that the pipe can be bent without cracking, which is a good sign, but the practical lesson is that the bending must be followed by a full PWHT to restore the properties of the bend region. I have seen T91 bends that were formed correctly but then used without PWHT, and they failed in service after only a few thousand hours due to the high residual stresses and the hard martensite in the bend. The paper's inclusion of the bending test is a sign that the authors understand the real-world requirements of a boiler tube, not just the laboratory tests.

Study Insights and the Veteran's Verdict

This paper is a straightforward qualification report, and it does what it should: it confirms that the domestic T91 pipe meets the standard requirements. However, the value of the paper lies in what it implies about the qualification process. The qualification of T91 is not just about testing the pipe; it is about testing the entire manufacturing chain — the steelmaking, the rolling, the heat treatment, the welding and the forming. The paper's results show that Baosteel's production route produces a pipe with acceptable properties, but the qualification must be repeated for each heat of steel and each pipe size, because T91 is sensitive to small variations in composition and heat treatment. My advice to any boiler manufacturer is to require a full qualification package for each new heat of T91, including a simulated PWHT on the weld test coupons and a hardness survey, and to insist that the bending procedure is qualified separately from the welding procedure. The paper is a useful reference for the minimum requirements, but it is not a substitute for a comprehensive welding procedure qualification that includes the actual production conditions. In conclusion, the paper confirms that domestic T91 pipe can meet the requirements of GB/T 5310-1995, and it provides a good baseline for anyone starting a qualification program. The key takeaway is that the qualification must be treated as a system-level test, not just a material test, and that the hardness of the weld and HAZ is the parameter that most often determines success or failure in service.