ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Innovative Bending Machine Design for Stainless Steel Coil-Wound Heat Exchanger Tube Bundles

Why Coil-Wound Heat Exchangers Demand a Special Bending Solution

The paper by Zhang Jianguo and Wu Fucheng addresses a problem that is well known in the cryogenic and chemical process industries: the fabrication of coil-wound heat exchangers, which are used in ammonia synthesis, methanol washing and air separation units. These exchangers are extremely compact, with hundreds of small-diameter stainless steel tubes wound in multiple layers around a central core. The tubes must be bent to precise radii, and the ends of the tubes must be connected to a collection header, which requires a tight bend at the tube-to-header junction. The challenge is that the tubes are small, thin-walled and made of austenitic stainless steel, which has a high coefficient of thermal expansion and a relatively low thermal conductivity. The bending must be precise, because the tubes are packed closely together and any deviation in the bend radius will cause interference between adjacent layers. The paper describes an innovative design for a bending machine that uses a screw-rod rotary device to achieve precise, portable and flexible bending, specifically for the "来回弯" (back-and-forth bend) that is required at the tube ends.

The Innovative Design: Screw-Rod Rotary Mechanism and Portability

The core of the innovation is the use of a screw-rod rotary device, which converts the linear motion of a screw into the rotary motion of the bending die. This is a simple but effective mechanism that provides high torque at low speed, which is exactly what is needed for bending small-diameter stainless steel tubes without causing wrinkling or ovality. The design is described as "portable" and "操控灵活" (flexible in operation), which means it can be used directly on the shop floor, close to the heat exchanger shell, rather than requiring the tube to be moved to a large stationary bending machine. This is a significant advantage, because the tube bundles are large and difficult to move once assembled. The design also allows for "back-and-forth" bending, which is the most difficult operation because it requires the tube to be bent in one direction, then straightened slightly and bent in the opposite direction, all within a very short length. The screw-rod mechanism provides the precise control needed to achieve this without exceeding the tube's elastic limit or causing work hardening.

The practical benefits of this design are clear from a manufacturing perspective. First, it reduces the handling of the tube bundle, which is a major source of damage in traditional fabrication. Second, it allows the operator to make adjustments on the spot, which is essential when the tube spacing is tight and the tolerances are in the order of 1–2 mm. Third, it reduces the cost of the bending equipment, because a screw-rod mechanism is cheaper and more reliable than a hydraulic or servo-driven system. The paper's focus on the "集合管端弯管密布" (densely arranged bends at the collection header) is particularly relevant, because this is the area where most fabrication problems occur. If the bends are not precise, the tubes will not align with the header holes, and the welds will be under high stress, leading to premature failure.

Manufacturing Process Challenges and the Role of the Bending Machine

The paper also discusses the manufacturing process of coil-wound heat exchangers, which is a complex sequence of winding, bending, welding and heat treatment. The key challenges are summarised in the table below, based on my experience with similar equipment in the air separation and LNG industries.

Challenge Traditional Approach Innovative Approach Practical Benefit
Tube-to-header bend Manual bending or large machine Portable screw-rod bender Precise, on-site bending without moving the bundle
Back-and-forth bend Two separate operations Single operation with screw-rod control Reduced handling and risk of damage
Tube spacing control Manual measurement Integrated with bending die Consistent spacing, no interference
Thermal expansion compensation Complex design calculations Flexible bend provides natural compensation Reduces stress at the header weld
Equipment cost High (hydraulic bender) Low (screw-rod mechanism) Accessible to smaller fabricators
Operator skill High (manual bending) Moderate (machine-assisted) Reduced training time and error rate

The thermal expansion compensation aspect is critical. The paper mentions that the bend is designed to provide "柔性补偿" (flexible compensation) for the thermal expansion and contraction of the tubes during operation. This is a clever design feature, because the bend acts as a spring, absorbing the differential expansion between the tubes and the shell. Without this flexibility, the tubes would be subjected to high thermal stresses, and the tube-to-header welds would crack. The bending machine must be able to produce a bend with a consistent radius and a smooth transition, because any sharp corner would act as a stress concentrator and defeat the purpose of the flexible connection. The screw-rod rotary mechanism, with its precise control, is well suited to this task.

Study Insights and the Veteran's Perspective

This paper is a good example of how a simple mechanical innovation can solve a complex manufacturing problem. The screw-rod rotary device is not a high-tech solution, but it is a practical one, and it addresses the real needs of the shop floor. My experience with coil-wound heat exchangers tells me that the tube bending operation is often the bottleneck in the fabrication schedule, and that the quality of the bends directly affects the performance of the exchanger. A bend that is too tight will cause thinning of the tube wall and a reduction in burst pressure; a bend that is too loose will cause interference between adjacent tubes and a reduction in heat transfer efficiency. The paper's design, by providing precise control and portability, addresses both of these issues. I would add one practical suggestion: the bending machine should be equipped with a digital angle indicator and a spring-back compensation mechanism, because stainless steel has a significant spring-back, and the operator needs to know the actual bend angle, not just the position of the screw. The paper does not mention this, but it is a common problem in stainless steel bending, and it is the difference between a good bend and a reject. In conclusion, the paper provides a valuable contribution to the fabrication of coil-wound heat exchangers, and the screw-rod rotary bending machine is a practical and cost-effective solution to the tube bending problem. The key takeaway is that innovation does not always mean complex electronics; sometimes a well-designed mechanical mechanism is the best answer, and the portable, flexible design described in the paper is a testament to that principle.