ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

High-Performance CFST Composite Truss Girder Bridges: A Pipe Supplier's Perspective on a Game-Changing Structure

Overview of the Bridge System and What It Means for the Pipe Industry

When I first read about the high-performance steel tube concrete composite truss girder bridge proposed by Gao Yimin, Liu Yongjian, Zhou Xuhong and their colleagues, I saw more than just another paper from the academic world. I saw a structural form that could change how we, as steel pipe manufacturers and suppliers, think about our product. This bridge type, developed through the National Key R&D Program and several provincial transportation department research projects, is not a laboratory curiosity. It is a serious candidate for medium-span highway bridges in China, and it deserves our full attention.

The concept is elegant in its simplicity. Instead of using traditional concrete box girders or steel plate girders, the system uses concrete-filled steel tube (CFST) members arranged as a truss. The top and bottom chords are CFST members, the diagonals and verticals are also CFST or hollow steel sections, and the deck is a prefabricated concrete slab. The paper reports that when the structural span reaches 80 m, the steel consumption index remains below 400 kg/m². That is a remarkable figure. For comparison, a conventional steel plate girder bridge of similar span might consume 350 to 450 kg/m² of steel, but it would require significantly more fabrication labor, more welding, and more on-site assembly time. The CFST truss achieves comparable or better steel efficiency while offering a much simpler fabrication and erection path.

From my years on the shop floor and at delivery sites, I can tell you that the real value of this system lies not in the laboratory test results, but in what it means for the people who have to make the steel tubes, weld the joints, and ship the components. The paper emphasizes that the main truss units, deck slab units, and pier units can all be produced in a factory with standardized processes. This is exactly what our industry needs. When we can produce repetitive, standardized components in a controlled factory environment, we can achieve consistent quality, predictable delivery schedules, and lower overall costs.

The paper's comparison with concrete box girder bridges is particularly striking. In response spectrum analysis, the longitudinal pier bottom bending moment and shear force decreased by 94.0% and 81.2%, respectively. In time-history analysis, the longitudinal pier bottom bending moment decreased by 91.6%. These are not marginal improvements. They represent a fundamentally different structural behavior under seismic loading. The CFST truss is lighter, stiffer, and more ductile than a concrete box girder of equivalent span, which means the seismic demands on the substructure are dramatically reduced. For a pipe supplier, this means we are not just selling tubes; we are selling a structural system that can reduce the cost of foundations, piers, and seismic isolation systems.

PBL Stiffened Joints and Rectangular CFST Members: Fabrication Implications

The paper introduces two key innovations that have direct implications for pipe fabrication: PBL (Perfobond Leiste) stiffened equal-width CFST joints and PBL stiffened rectangular CFST members. Let me explain what these mean in practical terms.

PBL stiffeners are steel plates with circular holes, welded inside the steel tube at the joint region. The concrete flows through these holes, creating a mechanical interlock between the steel and concrete. This is not a new concept in composite structures, but applying it to CFST truss joints is a significant advancement. The paper reports that PBL stiffened joints improve the force transfer mechanism, the static failure mode, and the fatigue performance of the joint.

From a fabrication standpoint, this creates several challenges. First, the PBL plates must be precisely positioned and welded inside the tube. This is not a simple fillet weld on the outside; it is an internal weld that requires careful access and control. Second, the holes in the PBL plates must be accurately punched or drilled to ensure the concrete can flow through and form the mechanical interlock. Third, the welding sequence must be carefully planned to minimize distortion. If the PBL plates are welded on one side first and then the other, the tube can warp, making it difficult to fit the joint with the adjacent member.

For the rectangular CFST members, the paper reports that PBL stiffeners improve the steel-concrete interface force transfer and the local buckling performance of the steel tube. This is critical because rectangular tubes are more prone to local buckling than circular tubes due to their flat walls. The PBL stiffeners act as internal diaphragms that restrain the flat walls from buckling inward or outward.

In my experience, fabricating rectangular CFST members with internal stiffeners requires a different approach than standard rectangular hollow sections. We typically use a forming process for the rectangular tube, either by roll-forming from a flat plate or by bending and welding four plates together. If we use the latter approach, we can install the PBL stiffeners before closing the last longitudinal seam. This allows us to weld the stiffeners from the inside with proper access. However, it also means we need to plan the welding sequence carefully to avoid excessive distortion.

The paper's finding that PBL stiffened rectangular CFST members effectively improve the bearing capacity is important for our product development. If we can offer a rectangular CFST member with internal PBL stiffeners that has higher capacity than a plain rectangular CFST member of the same size, we can provide more value to our customers. But we must also be honest about the fabrication cost. Adding PBL stiffeners increases labor, welding, and inspection time. The question is whether the performance gain justifies the cost increase.

Prefabrication, Transport, and Site Assembly: Tolerance Control

The paper emphasizes that the main truss units, deck slab units, and pier units can be produced in a factory with standardized production. This is music to my ears. The more we can move fabrication off-site and into a controlled factory environment, the better the quality and the more predictable the schedule. However, this also means we must pay close attention to tolerances.

When we prefabricate a truss unit in the factory, we are making a commitment. The unit must fit with the adjacent units on site. If our factory tolerances are too loose, we will have problems at the site. The paper does not provide specific tolerance values, but from my experience with similar structures, I can tell you what matters.

For CFST truss bridges, the critical tolerances are:

Parameter Typical Tolerance Why It Matters
Member length ±2 mm Affects truss geometry and force distribution
Member straightness L/1000 Affects buckling capacity and fit-up
Joint fit-up gap ≤2 mm Affects weld quality and residual stress
Tube diameter ±1% or ±2 mm Affects concrete filling and composite action
Wall thickness ±10% Affects capacity and weight
PBL hole position ±1 mm Affects concrete interlock and force transfer
Weld size +2 mm / -0 mm Affects joint strength and fatigue life

These are tight tolerances, but they are achievable with modern fabrication equipment. The key is to establish a measurement and control plan early in the project. We use a combination of laser measurement, template checking, and trial assembly to ensure that the prefabricated units will fit together on site.

Transport is another critical consideration. The paper mentions that prefabricated units must be stored, transported, and assembled efficiently. For a truss unit that is, say, 20 m long and 5 m wide, transport becomes a logistical challenge. We need to consider the route from the factory to the site, the height and width restrictions, and the lifting capacity at the site. In some cases, it may be more practical to fabricate smaller units and assemble them on site. In other cases, it may be better to fabricate large units and transport them by barge or special road transport.

The paper's mention of "replaceable bridge deck slabs" and "replaceable pier tie members" is a forward-thinking design concept. If a deck slab is damaged, it can be removed and replaced without affecting the main truss. This means the bridge can be maintained over its full life cycle without major disruptions. For us as pipe suppliers, this means we should design our connections to allow for easy removal and replacement. Bolted connections or special socket connections may be more appropriate than welded connections for these replaceable members.

Seismic and Durability Performance: Material Selection and Quality Assurance

The paper's seismic performance comparison with concrete box girder bridges is a strong argument for the CFST truss system. The dramatic reductions in pier bottom bending moment and shear force under seismic loading mean that the substructure can be designed with smaller sections, saving concrete and steel. But this also means the CFST truss itself must be designed to absorb more of the seismic energy through inelastic deformation.

For the steel tubes, this means we need to pay close attention to the material's ductility. The paper does not specify the steel grade, but from my experience, we would typically use Q355 or Q420 for the main chords and Q235 or Q355 for the diagonals and verticals. The steel must have adequate yield strength and ductility to allow for plastic hinge formation at the joints without fracture.

The durability performance is another critical aspect. The paper mentions that the CFST truss has good durability, maintainability, and environmental performance. This is partly due to the concrete filling, which protects the steel tube from internal corrosion. However, the external surface of the steel tube is still exposed to the environment. We need to ensure that the external surface is properly protected with a suitable coating system.

From a quality assurance perspective, the key issues are:

  1. Concrete filling quality: The concrete must fill the entire tube without voids. This requires careful mix design, proper placement methods, and adequate vibration. We typically use self-compacting concrete (SCC) for CFST members to ensure complete filling without vibration.
  2. Weld quality: The welds in the truss joints must be of high quality, especially in the fatigue-critical regions. We use full-penetration welds for the main chord connections and inspect them with ultrasonic testing (UT) or radiographic testing (RT).
  3. Coating quality: The external surface must be properly prepared and coated. We use blast cleaning to Sa 2.5 and apply a zinc-rich primer, followed by an intermediate coat and a topcoat. The coating system must be compatible with the site conditions and the design life of the bridge.
  4. Material traceability: All steel tubes must be traceable to their heat number and mill certificate. This is essential for quality control and for future maintenance planning.

Key Takeaways for Pipe Mills and Delivery Teams

The high-performance CFST composite truss girder bridge is a significant advancement in bridge engineering. For those of us in the steel pipe industry, it represents an opportunity to move beyond simple pipe supply and into the realm of structural system supply. The key takeaways are:

  1. Understand the structural system: We need to understand how the CFST truss works, not just how to make the tubes. This means we need to know the force paths, the joint behavior, and the concrete-steel interaction.
  2. Invest in fabrication capability: The PBL stiffened joints and rectangular CFST members require specialized fabrication capabilities. We need to invest in the equipment, tooling, and training to produce these components to the required tolerances.
  3. Focus on quality assurance: The quality of the steel tubes, the welds, and the concrete filling are critical to the performance of the bridge. We need to establish robust quality assurance plans and inspection procedures.
  4. Plan for logistics: Prefabricated units are large and heavy. We need to plan the transport and site assembly carefully to avoid delays and damage.
  5. Think about life cycle: The bridge is designed for a long service life with replaceable components. We need to design our connections and components to facilitate maintenance and replacement.

The paper by Gao Yimin and colleagues is a valuable contribution to the field. It provides a solid foundation for the design and construction of CFST composite truss girder bridges. For us in the pipe industry, it is a wake-up call. The future of medium-span bridges in China may well be built with our product, but only if we are prepared to meet the challenges of fabrication, quality, and delivery that this structural system demands.

I have seen too many projects where the pipe supplier treated the job as a simple "supply pipes and fittings" contract, only to find that the contractor needed much more: precise tolerances, specialized fabrication, and a deep understanding of the structural system. The CFST truss bridge is a prime example of a structure that rewards those who understand the whole picture and punishes those who only see the pipe. Let us learn from this paper and be ready for the next generation of bridge construction.