ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

PBL-Stiffened Rectangular Concrete-Filled Steel Tube Composite Truss Bridge: Design Insights and Shop Floor Lessons

Literature Overview and Design Context

The paper by Liu Bin, Liu Yongjian and colleagues presents the design of the Huangyan Bridge, a (24+40+24) m continuous rigid-frame composite truss bridge on an expressway overpass. The bridge employs a rectangular steel tube truss combined with a concrete roadway slab, Y-shaped bifurcated rectangular concrete-filled steel tube (CFST) piers, and diamond-shaped pile caps with bored pile foundations. The key innovation lies in the use of PBL (Perfobond Leiste) stiffening ribs within the rectangular steel tubes in the negative moment zone and the Y-shaped piers, with concrete infill forming a PBL-stiffened rectangular CFST section.

From my decades in the steel pipe and fabrication industry, I see this as a textbook example of how to marry structural steelwork with concrete in a way that respects the manufacturing constraints of rectangular hollow sections. The design team has clearly thought about how the sections are made, how the PBL ribs are fabricated, and how the concrete is placed — three things that often go wrong when structural engineers specify CFST without understanding the production reality.

Core Technical Points and Design Philosophy

PBL Stiffening Rib Configuration

The PBL rib is a steel plate with circular perforations, welded longitudinally inside the rectangular steel tube. When concrete is cast, the concrete flows through the perforations, creating a dowel action that locks the concrete and steel together. The key parameters are:

Parameter Typical Value Design Consideration
Rib plate thickness 10-16 mm Must be weldable to tube wall without distortion
Perforation diameter 30-50 mm Sized to allow concrete aggregate passage
Perforation spacing 100-200 mm Determines shear transfer capacity
Rib height 60-80% of tube depth Must not obstruct concrete placement
Concrete strength C40-C50 High flowability required for placement

The critical lesson here is that the PBL rib must be designed not only for structural performance but also for constructability. I have seen too many projects where the perforations are too small for the concrete mix, leading to honeycombing and voids that are only discovered during ultrasonic testing. The design team has wisely specified the PBL ribs in the negative moment zone, where the concrete is in tension and the steel tube is in compression — the PBL rib prevents local buckling of the compression flange while the concrete restrains the steel from inward buckling.

Negative Moment Zone Optimization

In a continuous truss bridge, the negative moment zone at the supports is where the bottom chord is in tension and the top chord is in compression. The design team has addressed this by:

  1. Filling the bottom chord with concrete to increase its compressive capacity.
  2. Placing PBL ribs inside the bottom chord to improve the bond between steel and concrete.
  3. Optimizing the node connections to improve load transfer.

From a fabrication standpoint, this means the bottom chord tubes must be delivered with the PBL ribs already welded in place, and the concrete must be pumped in after the truss is erected. This is a sequencing challenge that the shop floor must plan for carefully. The tube ends must be prepared with access holes for concrete placement, and these holes must be sealed after grouting to prevent moisture ingress.

Node Optimization

The design team has taken two measures to improve node capacity:

  1. Concrete infill in the chord (main member) at the node.
  2. Making the branch member the same width as the chord member.

The second measure is particularly interesting from a fabrication perspective. When a branch tube is the same width as the chord tube, the weld preparation becomes a simple butt joint rather than a complex saddle joint. This significantly reduces welding time and the risk of weld defects. The downside is that the branch member may have a higher stiffness than the chord, which can cause stress concentration. The concrete infill in the chord mitigates this by increasing the chord's stiffness and providing a more gradual load path.

Fabrication and Construction Practice

Rectangular Tube Manufacturing

The rectangular steel tubes used in this bridge are likely cold-formed from steel plate, with the longitudinal seam welded by submerged arc welding (SAW). The key quality issues are:

Defect Cause Countermeasure
Longitudinal seam misalignment Poor plate edge preparation Ensure edge milling accuracy ±1 mm
Corner cracking Cold forming with high yield strength steel Use pre-bending or hot forming for high-strength steel
Weld porosity Inadequate shielding gas coverage Check gas flow rate and nozzle condition
Distortion Uneven heat input during welding Use balanced welding sequence, consider post-weld straightening

For a bridge structure, the tubes are typically made from Q345 or Q420 steel. The welding consumables must match the steel grade, and the weld quality must meet the requirements of GB 50661 for steel structure welding. In my experience, the most common problem with rectangular tubes is the corner weld, where the heat input is concentrated and can cause distortion. The fabricator must use a jig to hold the tube during welding and may need to apply heat straightening after welding.

PBL Rib Fabrication and Welding

The PBL ribs are the most challenging component to fabricate. The perforations must be cut accurately, and the ribs must be welded inside the tube without causing distortion. The typical process is:

  1. Cut the rib plate from steel plate using plasma or laser cutting.
  2. Drill or punch the perforations.
  3. Fit the rib inside the tube using tack welding.
  4. Weld the rib to the tube wall using fillet welds.
  5. Inspect the welds using magnetic particle testing (MT) or ultrasonic testing (UT).

The welding sequence is critical. If the rib is welded on one side first, the tube will bow. The fabricator should use a symmetrical welding sequence, alternating between the two sides of the rib. For long tubes, the rib should be welded in segments, with the welding direction alternating to minimize distortion.

Concrete Placement

The concrete infill in the PBL-stiffened tubes must be placed after the truss is erected. The concrete mix must have high flowability to ensure it fills all the perforations and the space between the rib and the tube wall. The typical mix design is:

Component Proportion Note
Cement 400-450 kg/m³ Ordinary Portland cement
Water 160-180 kg/m³ Water-cement ratio 0.38-0.42
Fine aggregate 700-800 kg/m³ River sand or manufactured sand
Coarse aggregate 900-1000 kg/m³ Max size 20 mm
Superplasticizer 1.0-1.5% of cement weight Polycarboxylate-based
Silica fume 5-10% of cement weight Improves flowability and strength

The concrete should be pumped from the lower end of the tube, with vent holes at the top to allow air to escape. The pumping pressure must be controlled to avoid bursting the tube. After placement, the concrete must be cured for at least 7 days before the structure is loaded.

Key Questions and Reflections

What the Design Team Got Right

The design team has clearly thought about the interaction between the steel tube and the concrete. The PBL rib is not just a shear connector; it also serves as a stiffener that prevents local buckling of the tube wall. This dual function is elegant and efficient. The decision to make the branch member the same width as the chord is also wise from a fabrication standpoint, as it simplifies the weld joint and reduces the risk of defects.

What Could Be Improved

One area of concern is the long-term behavior of the concrete infill. The concrete will shrink over time, which can reduce the bond between the concrete and the steel tube. The PBL ribs mitigate this by providing mechanical interlock, but the shrinkage can still cause micro-cracking. The design should specify a shrinkage-compensating concrete or a low-shrinkage mix.

Another concern is the corrosion protection of the steel tube. The outside of the tube is exposed to the atmosphere and must be protected by a paint system. The inside of the tube, where concrete is placed, is protected by the concrete, but the area above the concrete level is exposed to moisture and must be protected. The design should specify a corrosion protection system for the internal surfaces of the tubes.

Study Insights and Practical Implications

This paper is a valuable contribution to the field of composite bridge design. It demonstrates that PBL-stiffened rectangular CFST sections can be used effectively in negative moment zones, and that the node optimization measures are effective in improving load transfer.

From a manufacturing perspective, the key takeaway is that the design must be developed in close collaboration with the fabricator. The PBL rib spacing, the perforation size, and the concrete mix design must all be coordinated to ensure that the concrete can be placed properly and that the welds can be made without distortion.

The bridge has been constructed and is in service, which validates the design approach. However, the long-term performance of the PBL-stiffened sections should be monitored to verify that the concrete-steel bond remains effective over time.

Reference Value and Outlook

This paper should be read by any engineer involved in the design of composite steel-concrete bridges. The PBL stiffening concept is applicable to a wide range of structures, including arch bridges, cable-stayed bridges, and building structures. The node optimization measures are particularly valuable for truss structures, where the node is often the weak link.

In the future, the use of higher strength steel and concrete in PBL-stiffened sections should be investigated. The current design uses Q345 steel and C50 concrete, but higher strength materials could reduce the section size and weight. The manufacturing challenges of higher strength steel, particularly in cold forming, would need to be addressed.