Experimental Study of Square Hollow Sandwich Concrete-Filled Steel Tube Members under Combined Compression, Bending, and Torsion: A Practical Review
Literature Overview and Research Context
This paper by Huang Hong, Zhu Qi, Chen Mengcheng, and Li Ting from East China Jiaotong University and the Jiangxi Provincial Key Laboratory of Building Process Simulation and Control investigates the behavior of square hollow sandwich concrete-filled steel tube (CFST) members under combined compression, bending, and torsion. The research was funded by the National Natural Science Foundation of China and the Jiangxi Provincial Young Scientists Program, and was published in the China Civil Engineering Journal in 2016.
The study is particularly relevant to the steel pipe industry because it addresses a complex loading condition that is common in structural applications such as bridge piers, building columns, and offshore structures. In my experience, members in these applications are often subjected to combined axial compression, bending moments, and torsional moments, particularly in seismic regions or where eccentric loading conditions exist. The hollow sandwich CFST concept, which consists of two concentric steel tubes with concrete filling the annular space between them, offers several advantages over conventional CFST members, including reduced weight, increased flexural stiffness, and improved seismic performance.
Key Technical Points and Experimental Findings
Experimental Program
The research involved testing of five square hollow sandwich CFST specimens and two square solid CFST specimens under combined compression, bending, and torsion. The main variable parameters were the slenderness ratio, the hollowness ratio (the ratio of the inner tube area to the outer tube area), and the axial compression ratio. The specimens were designed to represent typical structural members and were tested using a sophisticated loading system that allowed for the application of combined loads.
Torque-Twist Angle Relationship
The study used the finite element software ABAQUS to calculate the full torque-twist angle relationship for the specimens. The calculated curves showed good agreement with the experimental results up to the peak load, which validates the numerical model and provides confidence in the analysis approach. This is an important finding because it demonstrates that the finite element method can be used to predict the behavior of these complex members under combined loading.
Effect of Axial Compression Ratio
The research found that the torsional strength capacity of the specimens decreases as the axial compression ratio increases, particularly when the axial compression ratio is greater than 0.2. This is a significant finding with important practical implications. The axial compression reduces the torsional capacity because it increases the compressive stresses in the steel tubes and the concrete, which reduces the ability of the section to resist torsional shear stresses. This effect is more pronounced at higher axial compression ratios, where the section may approach its compressive capacity.
Effect of Hollowness Ratio
The study reveals that when the eccentricity is small, a higher hollowness ratio leads to increased torsional strength capacity and better ductility. This finding is intuitive: a higher hollowness ratio means that the inner tube is larger relative to the outer tube, which increases the moment of inertia of the section and improves its torsional stiffness. The increased ductility is attributed to the enhanced confinement provided by the inner tube, which delays the onset of local buckling and improves the post-peak behavior of the member.
Integration with Engineering Practice
Design Considerations
The findings of this research have direct implications for the design of square hollow sandwich CFST members under combined loading. Design engineers should carefully consider the axial compression ratio when sizing these members, as it has a significant effect on torsional capacity. In practice, this means that members subjected to high axial compression loads may require larger cross-sections or higher strength materials to achieve the required torsional capacity.
The hollowness ratio is another important design parameter that should be optimized based on the expected loading conditions. For members where torsional loading is significant, a higher hollowness ratio may be beneficial, as it increases both the torsional strength and the ductility. However, the hollowness ratio also affects the flexural and axial capacities, so a comprehensive optimization is required.
Fabrication and Construction
The fabrication of square hollow sandwich CFST members presents unique challenges compared to circular members. The square cross-section requires more complex fabrication procedures, particularly for the inner tube, which must be properly positioned and secured within the outer tube. In my experience, the most common method is to use temporary spacers or tack welds to hold the inner tube in place, but these must be designed to not create stress concentrations or interfere with concrete flow.
The concrete placement process for square hollow sandwich CFST members is also more challenging than for circular members. The square corners create areas where concrete flow may be restricted, leading to potential voids or incomplete filling. This requires careful design of the concrete mix and placement method, as well as adequate vibration to eliminate voids. In one project I was involved with, we discovered voids in the concrete fill at the corners of square CFST members, which required extensive remedial work.
Quality Control and Inspection
The quality control requirements for square hollow sandwich CFST members are more stringent than for conventional CFST members. In addition to the standard NDT requirements for the steel tubes, we must verify the concrete fill quality in the annular space between the tubes. This typically involves ultrasonic testing or radiography to detect voids or incomplete filling. The inspection must be particularly thorough at the corners, where voids are most likely to occur.
Key Questions and Reflections
This research raises several important questions that merit further investigation. First, the study focuses on square hollow sandwich CFST members, but the findings may not be directly applicable to circular members, which have different stress distributions and failure modes. The behavior of circular hollow sandwich CFST members under combined loading should be investigated separately.
Second, the research does not fully address the interaction between the inner and outer tubes. The bond between the inner tube and the concrete, as well as the bond between the concrete and the outer tube, is critical for the composite action of the member. The effects of these bond conditions on the torsional behavior have not been extensively studied.
Third, the study is based on a limited number of specimens, and the findings may not be fully representative of the range of geometries and material properties encountered in practice. More extensive experimental testing is needed to validate the findings and to develop design equations.
Study Insights and Implications
From my perspective as an industry veteran, this research provides valuable insights into the behavior of square hollow sandwich CFST members under combined loading. The key takeaways are:
- The axial compression ratio has a significant effect on the torsional strength capacity, with higher ratios leading to reduced capacity.
- The hollowness ratio affects both the torsional strength and the ductility, with higher ratios generally leading to improved performance when the eccentricity is small.
- The finite element method can be used to predict the behavior of these members under combined loading, providing a useful tool for design and analysis.
- The fabrication and construction of square hollow sandwich CFST members require careful attention to detail, particularly in the concrete placement and quality control procedures.
These findings have direct implications for the design, fabrication, and construction of square hollow sandwich CFST members in structures where combined loading conditions are expected.
Reference Value and Outlook
This research makes a significant contribution to the understanding of square hollow sandwich CFST members under combined loading. The experimental data and finite element analysis provide a foundation for further research and practical design. However, there is a need for more extensive experimental testing to validate the findings and to develop design equations that can be used in practice.
Looking ahead, I see several promising directions for future research. The investigation of circular hollow sandwich CFST members under combined loading would provide a more complete understanding of this technology. The development of design guidelines for hollow sandwich CFST members would facilitate their wider application in practice. Additionally, the investigation of the long-term behavior of these members under sustained loading and environmental exposure would address important durability concerns.
In conclusion, this paper provides a solid foundation for understanding the behavior of square hollow sandwich CFST members under combined compression, bending, and torsion. The findings are practical and directly applicable to engineering practice. As we continue to develop and refine our understanding of this technology, we should build on this research and address the remaining questions through a combination of experimental testing, numerical analysis, and field monitoring. The steel pipe industry has a critical role to play in this development, both through the manufacturing of high-quality steel tubes and through the sharing of practical experience in fabrication and construction.
Zhuojin Pipe Fitting Co., Ltd