ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Hysteretic Behavior of End-Plate Through-Bolt Connections between Rectangular Steel Tube Columns and H-Beams

Overview of the Study

This paper, published in Progress in Steel Building Structures, investigates the hysteretic behavior of a specific type of beam-column connection: the end-plate through-bolt connection between a rectangular steel tube (RHS) column and an H-beam. The authors conducted experimental tests and finite element analysis to study the hysteretic characteristics of this connection. They also proposed a restoring force model based on the experimental hysteresis curves, which can be used for the seismic design of steel frames. The study is significant because it addresses a gap in the design of connections for RHS columns, which are increasingly used in steel buildings due to their aesthetic appeal and structural efficiency.

Key Technical Findings and Their Practical Significance

The study's key findings are summarized in the table below.

Aspect Finding Practical Implication
Connection type End-plate through-bolt connection A practical solution for connecting H-beams to RHS columns
Hysteretic behavior Shows a stable hysteresis curve with good energy dissipation The connection has good seismic performance
Failure mode The connection fails by bolt yielding and end-plate deformation The failure is ductile, which is desirable
Restoring force model Proposed a model based on the experimental curves Can be used for the seismic design of steel frames
Finite element analysis The FE model can accurately simulate the behavior The FE model can be used for parametric studies

The most important takeaway from this study is the confirmation that the end-plate through-bolt connection is a viable solution for connecting H-beams to RHS columns. The connection shows a stable hysteresis curve with good energy dissipation, which indicates that it has good seismic performance. The failure mode is ductile, with the bolts yielding and the end plate deforming, which is a desirable failure mode because it provides a warning before the connection fails.

The proposed restoring force model is a valuable contribution to the design of steel frames. The model can be used to predict the hysteretic behavior of the connection under cyclic loading, which is essential for the seismic design of steel frames. The model is based on the experimental hysteresis curves, so it is a reliable representation of the actual behavior of the connection.

Integration with Manufacturing and Delivery Practice

For those of us who manufacture the steel tubes and the connection components, this study has several direct implications.

  1. Manufacturing of the RHS column. The RHS column must be manufactured to a tight tolerance to ensure a proper fit-up with the end plate. If the column is not square or if the dimensions vary, the end plate will not fit properly, and the bolts will not be able to provide the required clamping force. I would specify a tolerance of ±1 mm for the cross-section dimensions and ±0.5 mm for the wall thickness.
  2. Welding of the end plate. The end plate is welded to the RHS column. This weld must be of high quality to ensure that the end plate acts as a single unit with the column. I would specify a full-penetration butt weld for the connection between the end plate and the column, with 100% UT inspection. Any lack of penetration or lack of fusion will reduce the load capacity of the connection.
  3. Hole drilling and bolt installation. The through-bolts are installed through the end plate and the column. The holes must be drilled accurately to ensure that the bolts can be installed without excessive force. I would specify a hole tolerance of ±0.5 mm for the bolt holes. The bolts must be installed with the correct torque to ensure that the required clamping force is achieved.
  4. Material selection. The steel for the RHS column and the end plate must be a high-quality structural steel, such as Q345 or Q420, with a guaranteed yield strength and impact toughness. The bolts must be high-strength bolts, such as 10.9 or 12.9 grade, with a guaranteed tensile strength and yield strength.
  5. Corrosion protection. The connection is exposed to the environment, and it must