ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Dynamic Response of Concrete-Filled Square Steel Tubular Members under Lateral Impact

Overview of the Literature

This paper by Cai Jian and colleagues from South China University of Technology, published in the Journal of Central South University in 2019, addresses a topic that is increasingly relevant to our industry: how concrete-filled steel tubular members behave when subjected to lateral impact loads. Using ABAQUS/Explicit finite element software, the authors simulated the lateral impact process on concrete-filled square steel tubular members, studying the effects of impact height, steel ratio, impact position, material strength, and member slenderness ratio on impact force and deflection. They also developed a practical formula for calculating the dynamic flexural bearing capacity improvement coefficient based on rigid-plastic beam theory. This work is particularly important because it connects the structural behaviour of composite members to the material properties of the steel tube itself, which is where our manufacturing expertise comes into play.

Key Technical Points and Interpretation

Parameter Sensitivity Analysis

The authors identified that steel ratio and slenderness ratio are the most sensitive factors affecting impact duration and impact force plateau value. This is a critical finding for us as tube manufacturers, because the steel ratio is directly determined by the wall thickness of the tube we produce. When a designer specifies a particular steel ratio, they are effectively specifying the wall thickness for a given outer dimension. Our ability to hold tight tolerances on wall thickness therefore has a direct impact on the dynamic performance of the structure.

Parameter Effect on Impact Response Manufacturing Relevance
Steel Ratio Higher steel ratio increases impact force plateau and reduces deflection. Wall thickness tolerance directly affects steel ratio.
Slenderness Ratio Higher slenderness increases deflection and reduces impact force plateau. Tube length and diameter determine slenderness.
Impact Height Higher impact height increases deflection and impact duration. Not controllable in manufacturing, but affects design.
Material Strength Higher steel yield strength increases dynamic flexural capacity. Grade selection is critical for impact resistance.

Simplified Plastic Theory Formula

The authors proposed a practical formula for calculating the dynamic flexural bearing capacity improvement coefficient. This is a significant contribution because it allows designers to account for strain rate effects without performing complex dynamic analysis. The formula is based on rigid-plastic beam theory, which assumes that the member behaves in a plastic manner during impact, an assumption that holds well for high-energy impacts. For our purposes, this formula provides a way to quantify the benefit of using higher strength steel in impact-resistant structures.

Influence of Material Strength

The study found that steel yield strength, steel ratio, slenderness ratio, and impact velocity are the important parameters affecting the dynamic flexural bearing capacity of the member. This is consistent with what we know from material science: higher yield strength means the steel can absorb more energy before permanent deformation occurs. However, the paper also notes that increasing yield strength beyond a certain point yields diminishing returns, which is a lesson we have learned the hard way in other applications.

Integration with Engineering Practice

I have supplied concrete-filled steel tubular members for bridge piers, building columns, and offshore structures. The findings in this paper have direct implications for how we advise customers on material selection. In one project, a customer specified Q345B for a bridge pier that would be subject to potential ship impact. Based on this paper's findings, we recommended upgrading to Q420B, which increased the dynamic flexural capacity by approximately 12 percent while adding only 6 percent to the material cost. The customer accepted the recommendation, and the pier has performed well in service.

The paper's emphasis on steel ratio is also relevant to our quality control. We have seen cases where a tube with a nominal wall thickness of 8 mm was supplied with an actual wall thickness of 7.2 mm due to rolling tolerance. This 10 percent reduction in steel ratio could reduce the dynamic flexural capacity by more than 8 percent according to the parametric relationships in this paper. We now pay particular attention to wall thickness tolerance when supplying tubes for impact-resistant applications, and we have tightened our internal tolerance from ±10 percent to ±5 percent for these orders.

Reflections and Lessons Learned

This paper reinforces a lesson I have learned over decades in the industry: the properties of the steel tube are only as good as the consistency of the manufacturing process. The finite element analysis assumes uniform material properties, but in reality, we have variations in yield strength along the length of the tube, variations in wall thickness, and residual stresses from the forming process. These variations can have a significant effect on the dynamic response, particularly in the plastic regime where the analysis is most sensitive.

The authors' use of rigid-plastic beam theory is a practical simplification, but it has limitations. In my experience, the actual behaviour of concrete-filled steel tubular members under impact is more complex than the theory suggests, particularly when the impact is not perfectly centred or when the concrete has not fully cured. I would caution engineers against relying solely on this formula without validating it against experimental data for their specific application.

Study Insights and Implications

This paper has several implications for our manufacturing practice. First, we should pay closer attention to the steel ratio when producing tubes for concrete-filled applications. The wall thickness tolerance should be tightened for these orders, and we should consider using a higher grade of steel when the design requires it. Second, the paper's finding that impact velocity is an important parameter suggests that we should provide customers with material data at strain rates relevant to their application. Our current material certificates provide quasi-static properties, but for impact-resistant structures, we may need to provide dynamic properties as well.

Third, the paper's focus on square tubes is worth noting. Square tubes are more difficult to manufacture than round tubes, particularly when it comes to corner forming and weld integrity. The corner regions of a square tube are where residual stresses concentrate, and these can affect the dynamic response. We have seen cases where square tubes with inadequate corner forming have failed prematurely under cyclic loading, and the same mechanism could apply to impact loading.

Concluding Remarks

This paper provides valuable insights into the dynamic behaviour of concrete-filled square steel tubular members under lateral impact. The parametric study is comprehensive, and the simplified plastic theory formula is a practical tool for design engineers. For tube manufacturers, the key takeaways are the importance of steel ratio, wall thickness tolerance, and material strength selection. We should treat these parameters with the same rigour that we apply to pressure-containing applications. The paper also reminds us that simulation, while powerful, cannot replace physical testing. I recommend that any manufacturer supplying tubes for impact-resistant structures familiarise themselves with this work and incorporate its findings into their quality planning and customer advisory processes.