ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Impact Resistance of Stainless Steel Outer Tube Concrete-Filled Double Skin Steel Tube Columns

Introduction

This study by An Guoqing and colleagues from Taiyuan University of Technology addresses a gap that has long bothered me on the design side of protective structures. Concrete-filled double skin steel tube (CFDST) columns with a stainless steel outer tube are increasingly specified for bridge piers, offshore platforms and impact-prone industrial structures, yet most design guidance has been developed for solid concrete-filled steel tube (CFST) or reinforced concrete. The authors have taken their own earlier drop-weight test data and built a validated ABAQUS model to extend the understanding to the coupled action of axial load and lateral impact. For anyone who has seen what a ship impact or a vehicle collision does to a pier, this is not an academic exercise — it is the difference between a dented tube and a collapsed column.

Failure Mechanism and Energy Dissipation

The most important finding, and the one I would highlight to any junior engineer, is that the outer steel tube's plastic deformation is the dominant energy dissipation mechanism. In a CFDST column, the outer tube absorbs the bulk of the impact energy through local denting and global bending, while the inner tube and the sandwiched concrete contribute to load sharing but do not take over the energy dissipation role. This is a fundamental shift from the behaviour of solid CFST, where the concrete core provides significant resistance to localised indentation. The implication for design is clear: the outer tube's wall thickness, yield strength and strain hardening capacity are the first-order parameters, not the concrete strength. I have seen too many specifications where the concrete grade is bumped up to improve impact resistance, while the outer tube remains a thin, low-grade shell — that is money spent in the wrong place.

Parametric Effects on Impact Resistance

The parametric study reveals a hierarchy of influence that should be burned into the memory of every structural engineer. I have summarised the key findings in the table below.

Parameter Effect on Impact Resistance Practical Observation
Axial compression ratio Decreases resistance; effect becomes more pronounced above 0.5 High axial load reduces the tube's ability to deform plastically; a pier under heavy service load is more vulnerable to impact
Nominal steel ratio Increases resistance significantly More steel, especially in the outer tube, is the most efficient way to improve performance
Outer tube strength Increases resistance Yield strength and strain hardening are critical; stainless steel's high hardening rate is an advantage
Concrete strength Moderate effect The concrete core contributes to load sharing but not to energy dissipation
Impact velocity Decreases resistance (higher velocity reduces ductile response) Strain rate effects and localisation of damage become more severe at high speed
Section outer diameter Increases resistance Larger diameter spreads the impact over a wider area, reducing local denting

The finding that the axial compression ratio has a critical threshold at 0.5 is particularly valuable. In practice, this means that a column designed for a high axial load ratio under normal service conditions may be operating in a regime where its impact resistance is already compromised. I have seen this exact situation in a bridge pier retrofit project, where the original design had a compression ratio of 0.62 and the impact assessment revealed a severe deficiency. The solution was not to increase the concrete grade but to add an outer steel sleeve — exactly what this paper's parametric trends would suggest.

Proposed Calculation Method and Design Implications

The authors propose a formula for the dynamic increase factor (DIF) for the plateau impact force, which is the steady-state force level during the impact event. This is a practical contribution because the plateau force is what governs the global bending response of the column, and hence the design of the supporting structure and the foundation. The formula accounts for the key parameters identified in the parametric study, including the axial compression ratio, nominal steel ratio and material strengths. I would caution that the formula is calibrated on a limited set of finite element results, and the authors themselves note that it should be validated against more experimental data. However, as a first-order design tool, it is far better than the current practice of ignoring the axial load effect entirely, which is what many design guides still do.

Practical Lessons and Conclusions

From a manufacturing and delivery perspective, this paper reinforces several lessons I have learned the hard way. First, stainless steel outer tubes are not just a corrosion protection measure — they bring superior strain hardening and ductility that directly enhance impact resistance. When specifying stainless steel for a CFDST column, the designer should not simply substitute it for carbon steel on a one-to-one basis; the higher hardening rate should be exploited in the design. Second, the quality of the weld between the outer tube and the end plates or flanges is critical. A weld with poor fusion or excessive undercut will become the initiation point for fracture during impact, and I have seen this in a failed drop-weight test where the tube tore at the weld toe rather than denting in the middle. Third, the concrete filling process must be controlled to ensure full compaction, especially in the annular space between the two tubes. A void in the concrete will create a localised weakness that the finite element model will not capture but the impact will find. Finally, the paper's emphasis on the plateau force DIF reminds me that dynamic design is not about peak force alone. The duration of the impact and the energy it imparts are equally important, and any design method that only considers peak force will underestimate the damage in a high-energy, low-velocity impact scenario.

In conclusion, this study provides a solid foundation for the impact design of stainless steel CFDST columns, but the practical engineer must remember that the finite element model is only as good as the material properties and the weld quality that go into the real structure. The parametric trends are clear, the failure mechanism is well explained, and the proposed DIF formula is a useful starting point. I would recommend that any design office adopting this method also develops a site-specific quality plan for the tube fabrication and concrete filling, because the performance advantage of the stainless steel outer tube is only realised if the manufacturing defects are kept under control. The next step should be a full-scale impact test on a column with realistic boundary conditions, because the simply supported assumption used in the model may not capture the restraint effects seen in a real bridge pier.