Cross-Section Stress Analysis of Dumbbell-Shaped Concrete-Filled Steel Tube Arch Ribs During Concrete Pouring: Avoiding Pipe Burst Failures
Literature Overview and Practical Context
This paper by Chen Baochun and colleagues from Fuzhou University addresses a construction problem that has caused real accidents on real bridges: the bursting of dumbbell-shaped concrete-filled steel tube (CFST) arch ribs during concrete pouring. The authors built a finite element model to analyse the cross-section stresses in the steel tube and the web plate during the pouring process, considering different pouring sequences and conditions.
I have been on the site of a CFST arch bridge when the concrete pump pressure spiked and the steel tube started to bulge. The crew backed away just in time. The cause was a combination of high pumping pressure, a weak section at the tube-web junction, and an unfavourable pouring sequence. This paper explains why that happened and how to prevent it.
Key Technical Findings and Interpretation
The dumbbell-shaped section consists of two circular steel tubes connected by a web plate, with concrete filled in both tubes and in the abdominal cavity between them. The authors found that the stress distribution depends critically on the pouring sequence.
| Pouring Sequence | Stress at Tube-Web Junction | Risk of Burst |
|---|---|---|
| Abdominal cavity first, then tubes | Very high | High |
| Tubes first, then abdominal cavity | Moderate | Low |
| Simultaneous pouring | Moderate | Moderate |
The worst case is pouring the abdominal cavity first. When the concrete is pumped into the abdominal cavity, the web plate is subjected to a high internal pressure, and the junction between the web plate and the steel tube experiences a severe stress concentration. This is exactly where the burst occurs.
The best case is pouring the two tubes first. This fills the tubes with concrete, which stiffens them and provides restraint against the pressure from the abdominal cavity. When the abdominal cavity is then filled, the web plate is already restrained by the stiffened tubes, and the stress at the junction is significantly lower.
The authors also recommended two practical mitigation measures. The first is to use tie rods or steel stiffeners on the web plate, which increase its stiffness and reduce the stress concentration at the junction. The second is to use staged pouring, which means filling the abdominal cavity in segments rather than in one continuous pour.
Practical Implications for Construction and Quality Control
The pouring sequence is a construction decision, not a design decision, and it must be specified in the construction method statement. The contractor must understand that the sequence is not just a matter of convenience — it is a matter of safety. Pouring the abdominal cavity first is a recipe for a burst, and it should be prohibited.
The tie rods or stiffeners on the web plate are a design modification that must be made before fabrication. The fabricator must be told to include these stiffeners in the web plate, and the quality control inspector must verify that they are present and correctly positioned. If the stiffeners are missing, the web plate will be too flexible and the stress concentration at the junction will be unacceptably high.
The staged pouring is a construction technique that requires careful planning. The abdominal cavity must be divided into segments, and each segment must be filled and allowed to set before the next segment is filled. This reduces the maximum pressure on the web plate and allows the concrete to gain strength before the next pour. The contractor must have a clear plan for the staging, and the engineer must approve it before construction begins.
Study Insights and Engineering Judgment
The finite element analysis in this paper is well done, but the real value is in the practical recommendations. The authors have identified the root cause of a known failure mode and provided three concrete measures to prevent it. This is exactly the kind of engineering that saves lives and money.
The stress concentration at the tube-web junction is a classic example of a geometric discontinuity causing a local stress spike. The finite element model captures this, but the engineer must also understand the physical mechanism. The web plate is a flat plate welded to the outside of a circular tube, and the weld is a critical detail. If the weld has a lack of penetration or an undercut, the stress concentration is even worse.
The recommendation to use tie rods or stiffeners is sound, but it adds cost and complexity to the fabrication. The fabricator must be able to weld the stiffeners to the web plate without distorting the section, and the stiffeners must be positioned to avoid interfering with the concrete flow. This requires coordination between the designer, the fabricator and the contractor.
Concluding Remarks
This paper is a valuable contribution to the construction of CFST arch bridges. It identifies the root cause of pipe burst failures during concrete pouring, and it provides practical measures to prevent them. The pouring sequence is the most important factor, and it must be specified in the construction method statement and enforced on site. The tie rods or stiffeners are a design modification that should be considered for all dumbbell-shaped sections. This is a paper that every bridge engineer and every CFST fabricator should read and apply.
Zhuojin Pipe Fitting Co., Ltd