Steel Tube Concrete Support Technology for Deep Soft Rock Roadways
Overview of the Study
This paper by Han Lianchang, Liu Yong, Wang Chen, Kang Xiangtao, Wang Yuyang, and Leng Guanghai investigates the support technology for deep soft rock roadways using steel tube concrete supports. The study focuses on the 141211 transportation roadway of a coal mine, employing field investigation, deformation monitoring, laboratory tests, theoretical analysis, numerical simulation, and theoretical calculations. The research identifies the causes of roadway deformation and failure, and proposes a combined support scheme based on the principles of high-resistance yielding coupling support, key part reinforcement, and surrounding rock strengthening and water-blocking support.
Deformation Failure Mechanism and Support Scheme
| Factor | Contribution to Deformation Failure |
|---|---|
| Engineering geological conditions | Poor, low strength surrounding rock |
| Self-stability capacity | Weak, unable to maintain stability |
| Support design | Unreasonable, insufficient capacity |
| Construction quality | Poor, not meeting design requirements |
| Ground stress | High, exceeding rock strength |
| Water action | Significant, weakening rock mass |
The combined support scheme includes roof and side anchor bolts with wire mesh, high-strength anchor bolts at the side corners, grouting to a depth of 400 mm, and steel tube concrete supports. Industrial trials show that after roadway repair, the maximum roof deformation is 108 mm at 90 days, the two-side convergence is 72 mm, and the surrounding rock deformation stabilizes after 50 days, with total deformation within the controllable range.
Technical Interpretation and Support Mechanism
The steel tube concrete support is a key component of the combined support system. The steel tube provides high bending stiffness and axial capacity, while the concrete filling enhances the compressive strength and prevents local buckling of the tube. The grouting improves the strength and integrity of the surrounding rock, creating a composite bearing structure. The high-resistance yielding coupling support principle ensures that the support system can accommodate the large deformations of soft rock while maintaining resistance. The key part reinforcement addresses the critical zones where stress concentration occurs, such as the side corners. The water-blocking support prevents water from weakening the rock mass and the support system. The combination of these measures creates a multi-layered support system that can effectively control the deformation of deep soft rock roadways.
Connection with Manufacturing and Delivery Practice
From my experience in steel pipe manufacturing, the production of steel tube concrete supports for mining applications requires careful attention to several factors. The steel tube must have adequate wall thickness and diameter to provide the required bending and axial capacity. The tube should be manufactured from steel with good weldability and toughness, as the support may be subjected to dynamic loads from rock movement. The connections between the tube segments must be robust, typically using flanged or threaded connections, to allow easy installation in the confined space of the roadway. The concrete filling must be done after the support is installed, using a pump to inject the concrete through ports in the tube. The concrete mix must be designed for pumpability and high strength, with adequate workability to fill the entire tube without voids. In practice, we have seen cases where the concrete does not fully fill the tube due to inadequate pumping pressure or improper port placement. This reduces the effective capacity of the support and can lead to premature failure. The quality of the welds on the tube and the connections is critical, as any defect can lead to leakage of the concrete or failure of the support under load.
Critical Reflection and Lessons Learned
The study demonstrates the effectiveness of the combined support scheme, but the long-term performance of the steel tube concrete support in deep soft rock conditions needs to be monitored. The deformation data shows stabilization after 50 days, but the roadway may experience additional deformation over time due to creep of the rock mass and the concrete. The steel tube concrete support should be designed with a safety factor to account for these long-term effects. The grouting depth of 400 mm is a key parameter that must be carefully controlled. Inadequate grouting depth may not provide sufficient strengthening of the surrounding rock, while excessive grouting may be uneconomical. The grouting pressure and the grout mix must be optimized to ensure complete penetration into the rock fractures. The interaction between the steel tube concrete support and the grouted rock mass is complex and should be studied more thoroughly. The numerical simulation provides a valuable tool for understanding the stress distribution and optimizing the support parameters. However, the model must be calibrated with field measurements to ensure accuracy. The study also highlights the importance of construction quality. Poor installation of the support, such as inadequate bolt tension or improper grouting, can significantly reduce the effectiveness of the system. Strict quality control during installation is essential.
Study Insights and Future Directions
This research provides a comprehensive investigation of the deformation failure mechanism and support technology for deep soft rock roadways. The combined support scheme, including steel tube concrete supports, grouting, and anchor bolts, is effective in controlling deformation. The study highlights the importance of understanding the geological conditions and the interaction between the support system and the surrounding rock. Future work should focus on the long-term monitoring of the support performance and the development of design guidelines for steel tube concrete supports in deep soft rock conditions. The use of advanced materials, such as high-strength steel and fiber-reinforced concrete, should also be investigated. The optimization of the grouting parameters and the support spacing should be studied to improve the cost-effectiveness of the system. From a practical standpoint, the industry would benefit from standardized test methods and quality control procedures for steel tube concrete supports, ensuring their reliable performance in the challenging conditions of deep mines.
Zhuojin Pipe Fitting Co., Ltd