ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Radial Expansion Pressure of Static Cracking Agent in Steel Pipes

Literature Overview and Core Findings

This paper by Li Ruisen, Zheng Wenzhong, Xu Libo and Wang Ying from Harbin Institute of Technology addresses a topic that is not often discussed in the pipe industry but is directly relevant to our work: the use of steel pipes as a test medium for measuring the expansion pressure of static cracking agents.

The study uses seamless steel pipes to simulate drilled holes and measures the radial expansion pressure of static cracking agents during the hardening process using electrical resistance strain gauges. The authors tested 21 specimens and defined a "confinement degree" as the ratio of the steel pipe cross-sectional area to the static cracking agent cross-sectional area, based on the confining theory for concrete-filled steel tubes.

The key findings are that the radial expansion pressure is not uniformly distributed along the depth of the hole. Generally, the pressure at the middle and bottom of the hole is greater than at the top. Larger hole diameters result in a greater difference between the pressure at the bottom and the top, and a greater pressure at the middle and bottom within the same time period. The hole depth and confinement degree have little effect on the rate of pressure development, but the pressure at the middle and bottom increases with hole depth and confinement degree.

The practical conclusion is that selecting an appropriate hole depth and a larger hole diameter is more conducive to the static cracking agent achieving its full expansion potential.

Technical Interpretation from a Pipe Manufacturing Perspective

Let me translate this into the language of the pipe plant. The static cracking agent is a material that expands as it hydrates, and it is used in demolition and rock breaking. When it is placed in a drilled hole, the expansion pressure cracks the surrounding material. The challenge is that the expansion pressure is difficult to measure directly, because the pressure depends on the stiffness of the surrounding material.

The authors' approach of using steel pipes to simulate drilled holes is clever. The steel pipe provides a known stiffness, and the strain gauges measure the deformation of the pipe, from which the expansion pressure can be calculated. This is essentially a confined expansion test, and the results are directly relevant to the design of static cracking operations.

The finding that the expansion pressure is not uniformly distributed along the hole depth is important. In practice, this means that the cracking agent at the top of the hole is less effective than at the bottom. This could be due to the fact that the cracking agent at the top can expand upward and escape from the hole, while the agent at the bottom is confined by the agent above it.

The finding that larger hole diameters result in greater pressure at the middle and bottom is also important. This suggests that the cracking agent is more effective in larger holes, which is counterintuitive if one assumes that the pressure is simply proportional to the amount of agent. The explanation is that the larger hole provides more space for the agent to expand, and the confinement from the surrounding material is more effective.

Engineering Practice and Lessons Learned

I have seen static cracking agents used in a variety of applications, including the demolition of concrete structures and the breaking of rock in tunneling. The performance of the agent is highly dependent on the hole geometry and the confinement conditions.

In one case, a contractor was using a static cracking agent to break a large concrete foundation. The holes were drilled too close to the edge of the foundation, and the expansion pressure caused the edge to spall off instead of cracking the foundation. The lesson was that the hole placement must be designed to ensure that the expansion pressure is applied in the right direction.

In another case, the static cracking agent was placed in holes that were too shallow. The agent expanded and pushed out of the holes, creating a mushroom-shaped cap on the surface but not cracking the material below. The lesson was that the hole depth must be sufficient to ensure that the agent is confined.

The use of steel pipes as a test medium is a good approach because it provides a controlled environment for measuring the expansion pressure. However, the results are specific to the steel pipe geometry and material properties, and they may not directly translate to the behavior of the agent in rock or concrete, which have different stiffness and strength.

Standards and Specification Implications

There is no standard for the measurement of static cracking agent expansion pressure. The authors' approach of using steel pipes and strain gauges is a research method, not a standard test. This means that the results must be interpreted with caution when applied to practical design.

The key parameters that affect the expansion pressure are:

Parameter Typical Range Practical Consideration
Hole diameter 20–100 mm Larger holes are more effective
Hole depth 100–500 mm Deeper holes are more effective
Confinement degree 2–10 Higher confinement gives higher pressure
Agent water content 25–35% Must be controlled for consistent expansion
Ambient temperature 5–40 °C Affects hydration rate and expansion pressure

Key Questions and Reflections

The paper raises a question that I think is important for practical applications: what is the effect of the hole orientation on the expansion pressure? The paper tests vertical holes, but in practice, holes can be drilled in any orientation. The expansion pressure distribution may be different in horizontal or inclined holes, and this could affect the design of the cracking operation.

Another question is the effect of the cracking agent on the steel pipe itself. The expansion pressure is measured by the strain in the pipe, but the pipe may also be affected by the chemical reaction of the agent. The agent is typically alkaline, and it may corrode the steel pipe over time. This is not a concern for the test, but it could be a concern for the practical application of the agent in steel structures.

Study Insights and Implications

This paper is a good example of how a simple experimental setup can provide valuable information about a complex material. The use of steel pipes as a test medium is practical and provides a controlled environment for measuring the expansion pressure.

The practical takeaway is that the design of static cracking operations must consider the hole geometry and the confinement conditions. The expansion pressure is not uniform, and the effectiveness of the agent depends on the hole diameter and depth.

Reference Value and Outlook

This paper has direct reference value for the design of static cracking operations in demolition and rock breaking. It also has value for the pipe industry because it demonstrates the use of steel pipes as a test medium, which could be applied to other materials and applications.

Looking ahead, I would like to see more work on the effect of hole orientation and the long-term behavior of the cracking agent. I would also like to see more work on the development of a standard test method for measuring the expansion pressure, which would allow results from different studies to be compared.