Cyclic Axial Compression Behaviour of Special-Shaped Multi-Cavity CFST Columns
1. What This Paper Is Really About
This is a Beijing University of Technology study on a structural form that is becoming increasingly common in high-rise construction in China: the special-shaped multi-cavity concrete-filled steel tube (CFST) column. The test programme was based on the Z15 Tower in Beijing — a landmark project — and involved three large-scale specimens subjected to cyclic axial loading. The core question is straightforward: what happens when you put an internal reinforcement cage or an internal circular steel tube inside a multi-cavity rectangular column, and how does that change the load-deformation response, stiffness, ductility and energy dissipation under repeated loading?
From my years on the shop floor and on site, I can tell you that this is not an academic curiosity. Special-shaped CFST columns are being used more and more in high-rise buildings because they give architects the freedom to create column cross-sections that match the building envelope, while still providing the structural efficiency of concrete-filled steel tubes. The problem is that the multi-cavity form introduces internal diaphragms and partitions, and the interaction between the outer steel shell, the internal partitions, the concrete filling, and any additional internal reinforcement is complex and not fully captured by existing design codes.
2. Key Findings and Their Engineering Significance
2.1 Effect of Internal Reinforcement Cage
The test results show that adding an internal reinforcement cage inside the concrete-filled cavities increases both the initial stiffness and the load-carrying capacity of the column. This is intuitive — the rebar cage acts as a secondary reinforcement that restrains the concrete, delays cracking, and contributes to the composite action between the steel shell and the concrete core. The increase is not dramatic, but it is measurable and consistent.
2.2 Effect of Internal Circular Steel Tube
The more interesting finding is that placing an internal circular steel tube inside the column — essentially a steel tube within a steel tube, with concrete in between — provides a significant improvement in ductility, cumulative energy dissipation capacity, and post-peak performance. This is a classic case of confining the concrete more effectively. The circular tube provides a continuous, hoop-like restraint that is far more efficient than discrete reinforcement bars. The result is a column that can undergo larger deformations before failure and absorb more energy during cyclic loading, which is exactly what you want in a seismic region.
2.3 Code Verification — The Discrepancy
The paper compared the test results with calculations from several national codes, including Chinese, American and European provisions. The consistent finding is that the code-predicted capacities are significantly lower than the measured values. The authors attribute this to two factors that the codes do not properly account for: the contribution of the internal diaphragms (transverse stiffeners that connect the outer shell to the internal partitions), and the different yield mechanisms of the inner and outer steel plates.
This is a crucial point for practicing engineers. If the codes are conservative, that is not necessarily a bad thing — it means the design is safe. But it also means we are not getting the full benefit of the steel we are paying for. In a high-rise tower where column size is often governed by architectural constraints, a 20-30% underestimate of capacity means we are either oversizing columns or using more steel than necessary. That has direct cost and weight implications.
3. Practical Implications for Manufacturing and Construction
3.1 Fabrication of Multi-Cavity Columns
From a fabrication standpoint, multi-cavity CFST columns are demanding. The outer shell is typically made from thick steel plate (often 20-40 mm), formed into a rectangular or L-shaped section, with internal partition plates welded in place to create the individual cavities. The internal diaphragms — which the paper shows are important for capacity — must be welded with full penetration or at least sufficient strength to transfer load between the outer shell and the internal partitions.
The welding sequence is critical. You cannot simply weld everything in any order; you have to consider shrinkage and distortion. A typical sequence would be: assemble the outer shell, tack weld the partitions, complete the fillet welds on the partitions, then close the shell with the final longitudinal seam. If the column is long (which it often is — multi-storey columns are fabricated in sections and spliced on site), you need to control the straightness and the cross-section dimensions carefully. The internal partitions also complicate non-destructive testing — you cannot easily get an RT film behind a partition, so you rely on UT and MT for the internal welds.
3.2 Concrete Placement
The concrete filling is another practical challenge. With multiple cavities, you need to place concrete in each cavity separately, and you need to ensure the concrete reaches the bottom of each cavity without segregation. Self-consolidating concrete (SCC) is almost mandatory for these sections, and you need to plan the pour sequence to avoid trapping air or creating cold joints. The paper's finding that an internal circular tube improves performance is partly because it creates a more uniform confinement, but it also means the concrete section is annular (between the outer shell and the internal tube), which is easier to fill uniformly than a large rectangular cavity.
3.3 The Code Gap
The paper's conclusion that existing codes underestimate the capacity of multi-cavity CFST columns is important. In practice, this means that if you are designing such a column and using a code-based approach, you are likely to be conservative. But it also means that the code does not reward you for the additional steel you put in the form of diaphragms and internal tubes. The authors suggest that a new calculation method is needed that accounts for these effects. Until then, engineers should be aware that the code approach is a lower bound, and that a more refined analysis (such as finite element modelling calibrated against tests like these) could yield a more efficient design.
4. Lessons Learned and Recommendations
4.1 For Designers
If you are designing a special-shaped multi-cavity CFST column, do not rely solely on the code. Perform a refined analysis that explicitly models the internal diaphragms and the different yield strengths of the inner and outer plates. The tests show that the code is conservative, but the degree of conservatism varies with the geometry and the internal construction. A calibrated finite element model can give you a much better estimate of the actual capacity.
4.2 For Fabricators
Pay close attention to the welding of the internal partitions. These are not just stiffeners — they contribute to the load path. Ensure full penetration welds where required, and use appropriate NDT (UT and MT) to verify weld quality. Control the fit-up tolerances carefully; the internal dimensions affect the concrete filling and the composite action.
4.3 For Site Engineers
The concrete filling is the most critical site operation. Use SCC, plan the pour sequence to avoid voids, and verify the fill level using ultrasonic or other methods. The paper shows that the internal circular tube improves performance, but only if the concrete is properly placed around it.
5. Closing Thoughts
This is a well-executed experimental study that addresses a real gap in the design of a structural form that is becoming increasingly popular. The key takeaways are: internal reinforcement cages help, internal circular tubes help more, and the existing codes are conservative for these sections. The practical implication is that engineers should not blindly follow the code for these columns; they should invest in a refined analysis and work closely with the fabricator and contractor to ensure the construction quality matches the design assumptions. The cost of the additional analysis is small compared to the potential savings in steel and concrete, and the safety margin is already there.
Zhuojin Pipe Fitting Co., Ltd