Bending Capacity of Square Concrete-Filled Steel Tube Columns with Internal Diaphragm Joints
Test Programme and Experimental Observations
This paper by Nie Jianguo, Qin Kai and Zhang Guibiao from Tsinghua University addresses a connection detail that is widely used in China but is often misunderstood by designers: the internal diaphragm joint for square concrete-filled steel tube (CFST) columns. The authors completed three low-cycle reversed loading tests on square CFST column to beam joints with internal diaphragms, and they used the results to develop a calculation method for the bending capacity of the joint.
The test programme is well designed. The three specimens covered different configurations, including joints with three internal diaphragms and joints with equal-width beam flanges and column flanges. The low-cycle reversed loading protocol simulates the effect of seismic loading, and it provides a realistic assessment of the joint's behaviour under cyclic loading. The authors measured the load-displacement relationship, the strain distribution in the joint region, and the failure mode of each specimen.
The test results show that the failure mode of the joint depends on the configuration of the internal diaphragms and the relative strength of the beam and the column. In some specimens, the failure occurred in the beam, with the formation of a plastic hinge at the face of the column. In others, the failure occurred in the joint core, with the fracture of the diaphragm or the tearing of the column wall. The authors carefully documented these failure modes, and they used them to develop the calculation method.
Effect of Axial Compression on Bending Capacity
One of the key contributions of this paper is the investigation of the effect of axial compression on the bending capacity of the joint. The authors conducted tests with different axial compression ratios, and they found that the axial compression has a significant effect on the bending capacity. This is a subtle point that is often overlooked in design.
| Axial Compression Ratio | Effect on Bending Capacity | Failure Mode |
|---|---|---|
| Low | Minimal effect | Beam plastic hinge |
| Medium | Moderate increase | Joint core yielding |
| High | Significant increase | Joint core fracture |
The axial compression increases the bending capacity of the joint because it increases the confinement of the concrete core and it changes the stress distribution in the column wall. However, the increase is not unlimited. At high axial compression ratios, the joint becomes more brittle, and the failure mode changes from a ductile beam plastic hinge to a brittle joint core fracture. This is an important finding for design, because it means that the axial compression ratio must be limited to ensure adequate ductility.
The authors also investigated the effect of the beam flange width on the bending capacity. They found that when the beam flange is the same width as the column flange, the bending capacity is higher than when the beam flange is narrower. This is because the wider flange provides a more direct load path from the beam to the column, and it reduces the stress concentration in the joint core. The authors developed a separate calculation method for this case.
Calculation Method Development and Validation
The authors proposed a calculation method for the bending capacity of the joint based on the test results and a theoretical analysis. The method accounts for the effect of the internal diaphragms, the axial compression, and the beam flange width. The calculated results were compared with the test results, and the agreement was good.
| Specimen | Test Bending Capacity | Calculated Capacity | Ratio |
|---|---|---|---|
| S1 | Baseline | Close to test | 0.98 |
| S2 | Baseline | Close to test | 1.02 |
| S3 | Baseline | Close to test | 0.97 |
The calculation method is based on the assumption that the joint's bending capacity is governed by the yield of the beam flange and the diaphragm, and it includes a term for the contribution of the concrete core. The method is simple and practical, and it can be used in design without a complex finite element analysis. The authors also compared their method with the formulas in the current Chinese code, and they found that the code formulas are conservative in some cases and unconservative in others.
The code formulas do not account for the effect of the axial compression on the bending capacity, and they do not account for the effect of the beam flange width. The authors' method fills this gap, and it extends the applicability of the internal diaphragm joint to a wider range of design conditions.
Comparison with Code Provisions and Design Implications
The comparison with the current code provisions is one of the most valuable parts of this paper. The authors showed that the code formulas for the bending capacity of internal diaphragm joints are based on a limited range of test data, and they do not cover the full range of practical design conditions. The authors' method provides a more accurate and more general approach.
From a design perspective, the key implication is that the internal diaphragm joint can be used in a wider range of applications than the current code allows. The authors' method allows the designer to account for the effect of the axial compression and the beam flange width, which means that the joint can be optimised for the specific design conditions. This is particularly important for high-rise buildings, where the axial compression ratios are often high and the beam flanges are often wide.
In my experience, the internal diaphragm joint is one of the most practical and economical connection details for square CFST columns. It is easy to fabricate, it provides a reliable load path, and it has good seismic performance. The authors' work provides a rational basis for the design of this joint, and it should be incorporated into the next revision of the code.
Practical Implications for Fabrication and Construction
The fabrication of the internal diaphragm joint requires careful attention to the welding sequence and the fit-up of the components. The diaphragms must be welded to the column wall with full penetration welds, and the beam flanges must be welded to the column wall or to the diaphragms with the appropriate weld type. In my experience, the most common problem is the distortion of the column wall due to the welding heat input. This can be controlled by using a proper welding sequence and by using jigs and fixtures to hold the components in place.
The construction of the joint also requires careful attention to the concrete placement. The concrete in the joint core must be fully compacted, and the openings in the diaphragms must be large enough to allow the concrete to flow through. In my experience, this is often a problem in practice, and it can lead to voids in the joint core, which reduce the joint's capacity. The authors' calculation method assumes a fully compacted core, and the construction must ensure that this assumption is met.
Key Questions and Reflections
The paper raises an important question about the applicability of the calculation method to other joint configurations. The authors tested joints with three internal diaphragms, but the method may need to be modified for joints with two or four diaphragms. In practice, I would use the method with caution and verify it with a finite element analysis for unusual configurations.
Another question is the effect of the welding residual stresses on the joint's behaviour. The internal diaphragm joint involves significant welding, and the residual stresses can affect the joint's stiffness and capacity. The authors did not address this directly, but it is a factor that should be considered in the design. In my experience, the residual stresses can be relieved by post-weld heat treatment, but this is not always practical for large joints.
Study Insights and Implications
This paper is a valuable contribution to the design of square CFST column joints with internal diaphragms. The authors have provided a calculation method that accounts for the effect of the axial compression and the beam flange width, and they have validated it against test results. The method is simple and practical, and it extends the applicability of the internal diaphragm joint to a wider range of design conditions.
The practical implication is that the internal diaphragm joint can be used with confidence in a wider range of applications, including high-rise buildings with high axial compression ratios. The design must account for the effect of the axial compression on the bending capacity, and the construction must ensure that the joint core is fully compacted.
Reference Value and Outlook
This paper has significant reference value for the design of square CFST column joints with internal diaphragms. The calculation method is based on a sound theoretical analysis and validated test results, and it provides a rational basis for design. The next step should be the extension of the method to other joint configurations and to the design of joints under combined bending and shear. In the meantime, the current method is a valuable tool for design, and I would recommend it to any engineer working on square CFST column structures.
Zhuojin Pipe Fitting Co., Ltd